Stow CD613H18, CD605E16 Operation And Parts Manual

OPERATION AND PARTS MANUAL

CUTTER 1

CONCRETE/ASPHALT SAWS

CD613H18 (GASOLINE)

CD605E16 (ELECTRIC 5.0 HP)

MODEL #
SERIAL #

© COPYRIGHT 2003, MULTIQUIP INC.

Revision #4 (05/31/06)

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

A DIVISION OF MULTIQUIP INC.

POST OFFICE BOX 6254

CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX: [phone] • FAX: [phone]
E-MAIL: [e-mail] • WWW: stowmfg.com

PARTS DEPARTMENT:

800-427-1244
FAX: [phone]

SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:

800-478-1244
FAX: [phone]

P/N 25498

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING

PARTS DEPARTMENT

800-427-1244 or 310-537-3700
FAX: [phone] or 310-637-3284

SERVICE DEPARTMENT

800-421-1244
FAX: [phone]

TECHNICAL ASSISTANCE

800-478-1244
FAX: [phone]

WARRANTY DEPARTMENT

888-661-4279, or 310-661-4279
FAX: [phone]

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 3

STOW CUTTER 1 SAW — TABLE OF CONTENTS

Here's How To Get Help ............................................ 3

Table Of Contents ..................................................... 4

Parts Ordering Procedures ....................................... 5

Safety Message Alert Symbols .............................. 6-7

Rules For Safe Operation .................................... 8-10

Specifications (Saw) ................................................ 11

Specifications (Engine) ........................................... 12

STOW — CUTTER 1 SAW

Controls & Components .......................................... 13

Basic Engine ........................................................... 14

Preparation/Pre-Inspection ................................ 15-17

Blades ..................................................................... 18

Blade Placement ..................................................... 19

Initial Start-Up ....................................................20-21

Operation ................................................................ 21

Maintenance ...................................................... 22-23

Troubleshooting (Saw) ............................................ 24

Troubleshooting (Engine) ................................... 25-26

Explanation of Codes in Remarks Column ............. 28

Suggested Spare Parts ........................................... 29

Nameplate and Decals....................................... 30-31

Engine, Belts And Pulleys Assembly .................. 32-33

Electric Motor Assembly.....................................34-35

Undercarriage Assembly ................................... 36-37

Blade Assembly & Water System Assembly....... 38-39

Pointer Assembly ............................................... 40-41

HONDA GX390K1QWT2
ENGINE

Air Cleaner Assembly......................................... 42-43

Camshaft Assembly ........................................... 44-45

Carburetor Assembly ......................................... 46-47

Control Assembly ............................................... 48-49

Crankcase Cover Assembly ............................... 50-51

Crankshaft Assembly .........................................52-53

Cylinder Barrel Assembly ................................... 54-55

Cylinder Head Assembly .................................... 56-57

Fan Cover Assembly .......................................... 58-59

Flywheel Assembly ............................................ 60-61

Fuel Tank Assembly ........................................... 62-63

Ignition Coil Assembly ........................................ 64-65

Muffler Assembly ............................................... 66-67

Piston Assembly ................................................. 68-69

Recoil Starter Assembly..................................... 70-71

Labels ................................................................ 72-73

Terms and Conditions of Sale — Parts ................... 74

NOTE

Specifications and
part numbers are
subject to change
without notice.

PAGE 4 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — PARTS ORDERING PROCEDURES

When ordering parts,

please supply the following information:

❒❒

❒ Dealer account number

❒❒
❒❒

❒ Dealer name and address

❒❒
❒❒

❒ Shipping address (if different than billing address)

❒❒
❒❒

❒ Return fax number

❒❒
❒❒

❒ Applicable model number

❒❒
❒❒

❒ Quantity, part number and description of each part

❒❒
❒❒

❒ Specify preferred method of shipment:

❒❒

✓ FedEx or UPS Ground
✓ FedEx or UPS Second Day or Third Day
✓ FedEx or UPS Next Day
✓ Federal Express Priority One
✓ DHL
✓ Tr u c k

Note: Unless otherwise indicated by customer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours. We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.

Here’s how to get help...

Please have the model and serial number on
hand when calling.

Parts Department

800-427-1244 Fax: [phone]

310-537-3700 Fax: [phone]

Mayco Parts

800-306-2926 Fax: [phone]

310-537-3700 Fax: [phone]

Service Department

800-478-1244 Fax: [phone]

310-537-3700

MQ Power Service Department

800-835-2551 Fax: [phone]

310-537-3700

Warranty Department

800-421-1244, Ext. 279 Fax: [phone]

310-537-3700, Ext. 279

Multiquip’s Main Phone Numbers

800-421-1244 Fax: [phone]

310-537-3700

Place Your Parts Order Via Web or Fax

For Even More Savings!

Extra Discounts!

All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:

Ordered Standard Stock orders

via orders ($750 list and above)

Fax 3% 10%

Web 5% 10%

Special freight allowances
when you order 10 or more
line items via Web or Fax!**

FedEx Ground Service

No other allowances on freight shipped by any other
carrier.

NOTE: DISCOUNTS ARE SUBJECT TO CHANGE

at no charge for freight

MULTIQUIP INC.

18910 WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700 • 800-421-1244
FAX: [phone]
E-MAIL: [e-mail]
WWW: multiquip.com

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 5

QP-202TH TRASH PUMP — PARTS MANUAL— REV. 1 (01/07/03) — PAGE 5

Direct TOLL-FREE access

to our Parts Department:

Toll-free nationwide — 800-427-1244

STOW CUTTER 1 SAW — SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.

HAZARD SYMBOLS

NOTE

This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the

STOW CUTTER 1 SAW

information, please refer to the engine manufacturers
instructions for data relative to its safe operation.

Before using this CONCRETE/ASPHALT SAW,
ensure that the operating individual has read and
understands all instructions in this manual.

. For engine maintenance

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,

WARNING, or CAUTION.

Lethal Exhaust Gases

Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and

odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined

area or enclosed structure that does not
provide ample free flow air.

Explosive Fuel

Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in

approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.

DANGER: You WILL be KILLED or

SERIOUSLY injured if you DO NOT follow
directions.

WARNING: You CAN be KILLED or

SERIOUSLY injured if you DO NOT follow
directions.

CAUTION: You CAN be injured if you

DO NOT follow directions.

Potential hazards associated with STOW CUTTER 1 SAW
operation will be referenced with "
appear throughout this manual, and will be referenced in
conjunction with Safety "

Message Alert Symbols

Hazard Symbols

" which

".

Burn Hazards

Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.

Rotating Parts

NEVER operate equipment with covers, or

guards removed. Keep
and

clothing

prevent injury.

fingers, hands, hair

away from all moving parts to

PAGE 6 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — SAFETY MESSAGE ALERT SYMBOLS

Accidental Starting

ALWAYS place the engine ON/OFF

switch in the OFF position, when the saw
is not in use.

Over Speed Conditions

NEVER tamper with the factory settings of the

engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.

Guards and Covers In Place

NEVER operate the saw without blade guards

and covers in place. Adhere to safety
guidelines ANSI, OSHA, or other applicable
local regulations.

Respiratory Hazard

ALWAYS wear approved respiratory protection.

Sight and Hearing hazard

ALWAYS wear approved eye and hearing

protection.

Equipment Damage Messages

Other important messages are provided throughout this manual
to help prevent damage to your concrete saw, other property, or
the surrounding environment.

Rotating Blade

NOTE

Rotating blade can cut and crush. Keep
hands and feet clear.

This

concrete/asphalt saw

, other
property, or the surrounding
environment could be damaged if
you do not follow instructions.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 7

STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION

RULES FOR SAFE OPERATION

CAUTION:

Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.

The following safety guidelines should always be used when
operating the STOW CUTTER 1 SAW . Unless otherwise noted,
these guidelines refer to saws with gasoline powered engines.

SAFETY

■

DO NOT operate or service this equipment
before reading this entire manual.

■

This equipment should not be operated by persons under 18
years of age.

■

NEVER operate the saw without proper protective
clothing, shatterproof glasses, steel-toed boots
and other protective devices required by the job.

■

NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
the saw.

■

High Temperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact

hot!

with

■

The engine of this saw requires an adequate free flow of
cooling air. NEVER operate the saw in any enclosed or narrow

components can cause serious burns.

area where free flow of the
air is restricted. If the air flow
is restricted it will cause
serious damage to the saw's
engine and may cause injury
to people. Remember the
saw's engine gives off

DEADLY

gas.

carbon monoxide

■

■

NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.

■

NEVER operate the saw under the
influence or drugs or alcohol.

■

NEVER use accessories or attachments, which are not
recommended by STOW or Multiquip for this equipment.
Damage to the equipment and/or injury to user may result.

■

Manufacturer does not assume responsibility for any accident
due to equipment modifications. Unauthorized equipment
modification will void all warranties.

■

Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.

■

ALWAYS check the saw for loosened hardware such as nuts
and bolts before starting.

■

■

■

■

■

ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.

ALWAYS use extreme caution when
working with flammable liquids. When
refueling, STOP the engine and allow
it to cool.

NEVER

machine. Fire or explosion could result from

fuel vapors

engine.

NEVER operate the saw in an explosive atmosphere where
fumes are present or near combustible materials. An explosion
or fire could result causing severe

smoke

around or near the

, or if fuel is spilled on a

hot!

bodily harm or even

death.

Topping-off to filler port is dangerous, as it tends to spill fuel.

NEVER use fuel as a cleaning agent.

PAGE 8 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION

General Safety

■

ALWAYS read, understand, and follow procedures in
Operator's Manual before attempting to operate equipment.

■

ALWAYS be sure the operator is familiar with proper safety

■

■

precautions and operating techniques before using the saw.

■

NEVER leave the machine

■

Block the unit when leaving or when using on a slope.

■

ALWAYS check to make sure that the operating area is clear

unattended

while running.

■

before starting the engine.

■

Maintain this equipment in a safe operating condition at all

■

times.

■

ALWAYS stop the engine before servicing, adding fuel and
oil.

■

NEVER run the engine without the air filter. Severe engine
damage could occur.

■

ALWAYS service air cleaner frequently to prevent carburetor

■

■

Diamond Blade Safety

■

malfunction.

■

AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.

■

ALWAYS keep clear of

rotating

or

moving parts

while the

■

saw is in operation.

■

ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of
the reach of children.

■

NEVER use accessories or attachments which are not

■

recommended by the manufacturer for this equipment.
Damage to the equipment and/or injury to user may result.

■

WARNING

MAKE CERTAIN the power cord/extension cord is free from

damage and that the grounding circuit is operational.

MAKE CERTAIN the extension cord that you are using is

intended to be used in the environment you are using it in. If
an extension is used, NEVER submerge the connection in
water. To reduce the risk of electric shock, always make water­tight connections.

MAKE CERTAIN the "ON/OFF" switch is in the "OFF" position

before plugging in the power cord/extension cord to avoid
accidental starting.

Use only the gauge wire and length of cord recommended for
the motor size. Refer to Table 3 in this manual.

When cutting, ALWAYS be aware of the location of the cord.

NEVER use a

worn, frayed

or

damaged

extension cord.

Use appropriate steel centered diamond blades
manufactured for use on concrete saws.

WARNING

ALWAYS inspect diamond blades

before each use. The blade should
exhibit no cracks, dings, or flaws in
the steel centered core and/or rim.
Center (arbor) hole must be
undamaged and true.

Examine blade flanges for damage, excessive wear and
cleanliness before mounting blade. Blade should fit snugly
on the shaft and against the inside/outside blade flanges.

Ensure the blade is marked with an operating speed greater
than the blade shaft speed of the saw.

■

ALWAYS check to make sure that the

operating area is clear before starting the
engine.

■

Keep all inexperienced and unauthorized people away from
the equipment at all times.

Electric Saws

■

ALWAYS connect electric motor of the saw to a power source

in compliance with all local and state electrical codes. This
must be performed by a qualified electrician. After this
connection is made, it will be necessary to check the rotation
of the motor shaft. The shaft rotation should be

clockwise

when viewing the motor from the shaft extension
end. If the rotation of the shaft is incorrect make necessary
changes for the correct shaft rotation.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 9

counter-

■

Only cut the material that is specified by the diamond blade.
Read the specifications of the diamond blade to ensure the
proper tool has been matched to the material being cut.

■

ALWAYS keep blade guards in place. Exposure of the
diamond blade must not exceed 180 degrees.

■

Ensure that the diamond blade does not come into contact
with the ground or surface during transportation. DO NOT
drop the diamond blade on ground or surface.

■

The engine governor is designed to permit maximum engine
speed in a no-load condition. Speeds that exceed this limit
may cause the diamond blade to exceed the maximum safe
allowable speed.

■

Ensure that the blade is mounted for proper operating
direction.

STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION

Saw Transportation Safety

■

Use appropriate lifting equipment to ensure the safe
movement of the saw.

■

DO NOT use the handle bars and/or front pointer as lifting
points.

■

When trasporting of the saw is required, place saw directly
inside towing vehicle truck-bed and tie-down securely.
NEVER tow saw directly behind towing vehicle.

■

DO NOT use the saw on slopes or on extremely un-level
surfaces. An engine tipped to extreme angles may cause oil
to gravitate into the cylinder head making the engine start
difficult.

■

NEVER transport the saw with the blade

EMERGENCIES

mounted.

■

ALWAYS know the location of

the nearest

fire extinguisher

.

Machine Operation And Safety Decals

The STOW CUTTER 1 SAW is equipped with a number of
operation and safety decals. Should any of these decals become
unreadable, replacements can be obtained from your dealer.

■

ALWAYS know the location of the

nearest

■

In emergencies
nearest phone or
Also know the phone numbers of the nearest

first aid kit

ambulance, doctor,

information will be invaluable in the case of an
emergency.

.

always

know the location of the

keep a phone on the job site

and

fire department

.

. This

PAGE 10 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

Figure 1. STOW CUTTER 1 SAW Decals

A

STOW CUTTER 1 SAW — SPECIFICATIONS (SAW)

C

B

G

A

B

C

D
E
F

G

Side View

Front View

Figure 2. STOW CUTTER 1 SAW Dimensions

snoitacificepS1rettuC.1elbaT

RETTELECNEREFER NOITPIRCSED )mc(NOISNEMID

thgieHxaM

)desiaRretnioPtnorF(htgneLxaM

)derewoLretnioPtnorF(htgneLxaM

htdiWxaM )mc55(.nI5.12

esaBleehWraeR )mc04(.nI0.71

esaBleehWtnorF )mc4.52(.nI0.01

htdiWraBeldnaH )mc55(.nI5.12

F

E

D

)mc49(.nI0.73
)mc08(.nI0.23

)mc831(.nI5.45

ENIGNE

EPYT

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 11

NOITPIRCSED )GK(THGIEW

ENIGNEADNOHPH9,1RETTUC ).gk6.311(.bL052

ENIGNEADNOHPH31,1RETTUC )g.K7.221(.bL072

STOW CUTTER 1 SAW — SPECIFICATIONS (ENGINE)

)enignE(snoitacificepS.2elbaT

ledoM2TWQ1K093XGADNOH

epyT

ekortSXeroB

tnemecalpsiD)cc983(.ni-uc7.32

tuptuOxaM.M.P.R0063/.P.H0.31

enignE

yticapaCknaTleuF

leuF

yticapaCliOebuL)retil1.1(tqSU61.1

lortnoCdeepS

dohteM

dohteMgnitratStratSlioceR

noisnemiD

)HxWxL(

.xorppA

)sretiL5.6(

elgniS,ekorts4delooc-riA

enignEenilosaG,VHO,rednilyC

.ni5.2X.ni5.3

)mm46xmm88(

snollaG.S.U27.1

enilosaGelibomotuAdedaelnU

rehgihroenatcO68

epyTthgiew-ylFlagufirtneC

.ni4.71X7.71x0.51

)mm344X054X083(

yrD

thgieWteN

PAGE 12 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

).gK13(sbl4.86

STOW CUTTER 1 SAW — CONTROLS & COMPONENTS

CONTROLS & COMPONENTS

Figure 3 shows the location of the basic controls or components
for the STOW CUTTER 1 SAW. Listed below is a brief
explanation of each control or component. (Gasoline-powered
unit shown)

1. Hand Grips/Handlebar – When operating the saw, place
both hands on each grip to maneuver the saw. Replace
hand grips when they become worn or damaged.

2. Handle Lock – Lock blade depth to desired position.

3. Garden Hose Connecter – Connect to water source to

provide blade cooling while cutting concrete or asphalt.

4. Air Filter – Prevents dirt and debris from entering the engine
air intake. Check filter periodically and keep cleaned or
replace when necessary.

5. Recoil Starter Handle – Pull to engage and start the
engine.

6. Recoil Starter Assembly – Engages the engine when
the handle is pulled and rewinds the starter rope when the
handle is released.

7. Wheels/Carriage Assembly – Heavy-duty polyurethane
wheels with permanently sealed ball bearings.

8. Cutting Blade – Use appropriate type blades for cutting
concrete or asphalt.

9. Blade Guard – Covers saw blade and flips up to allow
blade to be changed.

10. Belt Tension Adjuster – Adjusts belt tension.

11. Front Pointer – Front pointer wheel assists in straight

tracking.

12. Front Pointer Arm – Stows up for storage and pivots down
for use.

13. Cutting Depth Adjuster – turn operating crank clockwise
or counter-clockwise to adjust the cutting depth up or down.

14. Fuel Tank – Use unleaded gasoline. Do not overfill.

15. Blade Coolant System – Provides cooling water to blade

during cutting operations.

16. V-Belt Cover – Remove this cover to gain access to the V­belt. NEVER operate the saw with this cover removed.

17. Arbor Shaft Grease Zerks – Conveniently located for
lubrication.

18. On/Off Switch – Turn to the "ON" position to allow engine
to be started and turn to the "OFF" position to shut the
engine off.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 13

Figure 3. Cutter 1

BASIC ENGINE

STOW CUTTER 1 SAW — BASIC ENGINE

Figure 4. Engine Controls and Components

Initial Servicing

The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing.

1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.

DANGER

Adding fuel to the tank should be done only when

the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry.

2. Throttle Lever – Used to adjust engine RPM speed (lever

advanced forward

FAST

).

3. Engine ON/OFF Switch – ON position permits engine

starting, OFF position stops engine operations.

4. Recoil Starter (pull rope) – Manual-starting method. Pull

the starter grip until resistance is felt, then pull briskly and
smoothly.

5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop

the flow of fuel.

SLOW

, lever back toward operator

6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.

7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.

NOTE

8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a month.

9. Muffler – Used to reduce noise and emissions.

operating. NEVER operate the engine with the muffler removed.

10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.

Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine, causing
rapid engine wear.

WARNING

Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after

PAGE 14 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION

PREPARATION / PRE-INSPECTION

1. Read and fully understand this manual,
the safety instructions in particular, and
the engine manufacturer's manual
supplied with the saw.

2. Select the correct blade for each application. If abrasive
blades are used, MAKE CERTAIN they are designed for
use on a concrete floor saw. They must be reinforced and
have a hole for the driving pin. When wet cutting with an
abrasive blade, MAKE CERTAIN the blade is intended for
wet cutting. Water will destroy a dry cut abrasive blade.
Some diamond blades require water cooling and failure to
do so will destroy them almost immediately. Other diamond
blades can be used with or without water. Refer to the Blades
and Blade Placement sections on pages 18 and 19 for further
information.

3. Handle all blades with care and NEVER use a damaged
blade. NEVER use an abrasive blade that has been
dropped.

Electric Powered Saws

1. The electric motor of this saw requires 230 VAC input

voltage (60 Hz, single-phase). Always make certain that
the rated operating line voltage of the motor is correct when
cutting. Electric motors can burn out when the line voltage
falls 10% below the voltage rating of the motor.

2. After the correct input voltage has been applied to the saw,

turn the saw on, and check the rotation of the motor shaft.
The shaft rotation MUST be counter-clockwise when
viewing the motor from the shaft extension end. If the rotation
of the shaft is incorrect make the necessary changes for
the correct shaft rotation.

3. MAKE CERTAIN the correct size extension cord is used.

Undersize extension cords can burn out an electric motor.
Use Table 3 to determine the correct extension cord size.

4.

NEVER!

use a

worn

or

frayed

extension cord.

5. Record the model and serial number of the saw on the

front of the Operating and Parts Manual for future reference.

eziSdroCnoisnetxE.3elbaT

ALWAYS use a grounded (3-wire) extension cord and MAKE
CERTAIN that the motor is connected to a properly grounded

electric circuit to protect the operator from possible electric shock.

Gasoline Powered Saws

1. Clean the
engine cooling air inlet, carburetor and air cleaner.

2. Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.

3. Check carburetor for external dirt and dust. Clean with dry
compressed air.

4. Check fastening nuts and bolts for tightness.

Engine Oil Check

1. To check the engine oil level, place the saw on secure level
ground with the engine stopped. The frame platform

be level

2. Remove the filler dipstick from the engine oil filler hole
(Figure 6) and wipe it clean.

WARNING

NEVER!
wet hands

touch the power cord (Figure 5) with

or while

standing in water

when it is connected to a power source. The
possibly exists of electrical shock (electrocution)
even death.

NEVER!

spray water directly on

the electric motor.

WET

HANDS

POWER

CORD

(POWER ON)

Figure 5. Extension Cord (Wet Hands)

saw,

removing dirt and dust, particularly the

must

to accurately check the engine oil.

eriW21.oNeriW01.oNeriW8.oNeriW6.oN

)teef(05

)sretem42.51(

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 15

)teef(57

sretem68.22(

2

)teef(001

sretem84.03(

)teef(00

sretem69.06(

Figure 6. Engine Oil Dipstick (Removal)

STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION

3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.

4. If the oil level is low (Figure 7), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).

Guards And Covers

Reference manufacturer engine

NOTE

manual for specific servicing
instructions.

Figure 6. Engine Oil Dipstick (Oil Level)

WARNING

NEVER operate the saw without blade guards

and covers in place. DO NOT operate with
the front of the blade guard raised. The blade
exposure cannot exceed 180 degrees during
operation. Adhere to the safety guidelines of
the American National Standards Institute

(ANSI) B7.1 and B7.5.

epyTliO.4elbaT

nosaeS erutarepmeT epyTliO

remmuS rehgiHroC°52 03-W01EAS

llaF/gnirpS C°01~C°52 02/03-W01EAS

retniW rewoLroC°0 01-W01EAS

Explosive Fuel

Fuel Check

Motor fuels are highly flammable and can be
dangerous if mishandled. DO NOT smoke
while refueling. DO NOT attempt to refuel the
trowel if the engine is

1. Remove the gasoline cap located on top of fuel tank.

2. Visually inspect to see if fuel level is low. If fuel is low, replenish
with unleaded fuel.

3. When refueling, be sure to use a strainer for filtration. DO

NOT top-off fuel. Wipe up any spilled fuel.

hot! or running

.

CHECK the following on the blade guard (Figure 8):

■

■

■

ENSURE the V-belt Cover is in place and securely fastened
during operation of the saw (Figure 8).

V-Belt Check

A worn or damaged V-belt can adversely affect the performance
of the saw. If a V-belt is defective or worn, replace ALL the V­belts. V-belts should always be replaced in sets.

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

Figure 7. Blade Guard

Ensure the capacity of the blade guard matches the diameter
of your diamond blade.

Check that the guard is bolted firmly upon the saw frame.
Check that the spring tensioned front cover of the guard is

firmly seated with the rear section of the guard and there are
no gaps. NEVER lift the blade guard while cutting.

NEVER attempt to check
the V-belt with the engine
running. Severe injury can
occur. Keep fingers, hands,
hair, and clothing away
from all moving parts.

PAGE 16 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION

V-belt Alignment and Tensioning

This saw is equipped with a premium V-belt that has been aligned
and tensioned by factory personnel. The V-belt must be aligned
and tensioned for proper operation of the saw.

Use the following procedure to check the alignment of V-belt:

1. Remove the bolts that secure the V-belt cover (Figure 9) to

the saw frame.

3. Check V-belt tension by using a tension meter (3.0 lbs.)

4. DO NOT over or under tighten the V-belt. Severe damage

Figure 9. V-Belt Cover

2. Check uniform parallelism (Figure 10) of V-belt and pulley

(sheaves). Use a straight-edge or machinist's square against
both pulleys and adjust both pulleys until equally aligned.

Figure 10. Pulley Alignment

against the inside belt at a mid point between the two pulleys,
or by deflecting the center belt at a mid point 3/16" (5 mm).

can occur to the saw and engine crankshaft if the belt is
over-tensioned. A decrease of power to the blade and poor
performance will result if the belt is under-tensioned (loose
on pulleys).

V-belt alignment must be

NOTE

rechecked after adjusting belt
tension.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 17

STOW CUTTER 1 SAW — BLADES

BLADES

Saw blades, or cutting disks, are available in either an abrasive
design or as diamond blades. Either blade will work on the
STOW CUTTER 1 SAW , however, diamond blades are
recommended. Ask your dealer about your specific cutting
application.

SAW BLADE INSPECTION

WARNING

Failure to thoroughly inspect the diamond
blade (Figure 11) for operational safety
could result in damage to the blades or
the saw and may cause injury to the user
or others in the operating area.

2. Edge of the Steel Core - Check the diameter edge for
discoloration (blue oxidation) indicating an overheating
condition caused by insufficient cooling water/air.
Overheating of blades may lead to loss of core tension and/
or increase the possibility for blade failure. Make sure the
steel core's width is uniform about the rim of the blade, and
not succumbing to an "under-cutting" condition brought
about by highly abrasive material or improper under-cutting
core protection.

3. Directional Arrow - Ensure that the blade is oriented
properly on the blade shaft for sawing. Reference the
directional arrow on the blade and place it so the direction
of rotation "downcuts" with the turn of the shaft.

4. Diamond Segment or Rim - Ensure there are no cracks,
dings, or missing portions of the diamond segment/rim. DO

NOT

of the rim.

cause damage to your saw or injury to the user or others in

1. Stress Relief Holes (Gullets) - Check the steel core for
cracks that may have propagated from the slots and/or
gullets. Cracks indicate extreme fatigue failure and if sawing
continues, catastrophic failure will occur.

the operating area.

5. Specifications - Ensure that the blade specifications, size,
and diameter properly match up to sawing operations.
Utilizing a blade not matched properly to the task may result
in poor performance and/or blade damage.

use a blade that is missing a segment or a portion

Damaged and /or missing segments/rims may

Figure 11. Diamond Blade

6. Arbor Hole - It is essential that the arbor hole diameter
properly matches the blade, and that it is free from distortion.
Correct blade flanges (collars) must be used. The inside
face of the flanges must be clean and free of debris. An out­of-round arbor condition will cause damage to the blade
and the saw.

7. MAX RPM - This RPM reference is the maximum safe
operating speed for the blade selected. NEVER exceed the
max RPM on the diamond blade. Exceeding the maximum
RPM is dangerous and may cause poor performance and
may damage the blade.

PAGE 18 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — BLADE PLACEMENT

BLADE PLACEMENT

WARNING

Failure to thoroughly inspect the diamond
blade for operational safety could result in
damage to the blades or the saw and may
cause injury to the user or others in the
operating area.

1. Blade Guard - Pivot the blade guard
front cover all the way back. The guard

tension spring will keep the front cover in position.

2. Blade Hex Nut - Unscrew the blade shaft nut (right side
loosens clockwise and tightens counter-clockwise while the
left side loosens counter-clockwise and tightens clockwise.
DO NOT overtighten the nut (approximately 45-50 ft. lb/61­68 N/m) when finalizing the assembly.

3. Outside Blade Flange (Collar) - Ensure that the outside
blade flange is placed flush against the diamond blade.
The inside surface of the flange must be free of debris and
permit a tight closure on the surface of the blade core.

4. Diamond Blade - Ensure that the proper diamond blade
has been selected for the job. Pay close attention to the
directional arrows on the blade. The blade's operating
directional arrows must point in a "down-cutting" direction
to perform correctly. When placing the blade onto the blade
shaft, ensure the arbor hole of the blade matches the
diameter of the shaft.

damage the diamond blade and may
cause serious damage to the saw and
bodily harm.

Blade Removal and Replacement

1. Set the engine ON/OFF switch to the

2. Place the saw on a stable level working

3. Ensure the blade is raised and the raise/lower crank is locked

5. Lift up the blade guard cover to gain access to the blade.

6. Use the provided blade nut and blade shaft locking

WARNING

Dropping or forcing the
blade onto the cutting
surface can severely

"OFF" position. (Unplug electric
models.)

surface.

into position.

When removing or installing a

NOTE

wrenches to remove and install the blade.

diamond blade, please note that the
blade retaining nuts are left and right­hand threaded.

5. Inner Flange (Collar) - This flange is fixed upon the blade
shaft. The inside surface of the flange must be free of debris
and permit a tight closure on the surface of the blade.

Blade Speed

A diamond blade’s performance is directly connected to specific
peripheral (rim) speeds.

The following shaft rotational speeds have been factory set to
ensure optimum blade performance.

z

CUTTER 1- 18-inch (457.2 mm) Capacity - 2,836 RPM.

NOTE

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 19

The following steps should be
accomplished before using the saw
on any cutting surface.

■

■

■

Cutting Depth Adjustment

The saw is equipped with a Raise/Lower Assembly that is
supported by the following components.

■

Raise/Lower Acme Screw

■

Jack Arm

■

Blade Guard

■

Adjusting Handle Crank

While holding the blade shaft with the locking wrench,
remove the blade hex nut (clockwise direction) and outer
blade flange.

Remove the old blade and install a new blade in the
same rotational direction as marked on the old blade.

Reinstall the outer blade flange and hex nut. Tighten
the nut firmly (counter-clockwise direction). DO NOT

OVER TIGHTEN.

STOW CUTTER 1 SAW — INITIAL START-UP

INITIAL START-UP

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

ALWAYS wear approved eye and hearing
protection before operating the saw.

DO NOT attempt to operate the saw until
the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
Depending on engine manufacturer,
operating steps may vary. See engine
manufactures operating manual.

NEVER operate the saw in
a confined area or
enclosed area structure
that does not provide ample

free flow of air

.

3. Place the

position.

NOTE

Engine ON/OFF switch

Figure 13. Engine ON/OFF Switch

(Figure 13) in the "ON"

The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD engine.
The OPEN position provides the
correct fuel mixture for normal
operation after starting, and for
restarting a warm engine.

NEVER place hands or feet inside the belt
guard or blade guard while the engine is
running. ALWAYS shut the engine down
before performing any kind of maintenance
service on the saw.

1. Ensure the diamond blade has been mounted correctly and

that it is raised above the surface you are about to saw.

2. Place the

fuel valve lever

(Figure 12) to the "ON" position.

4. Place the
position.

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

Choke Lever

Figure 14. Choke Lever

The engine speed has
been set at the factory.
Changing the governor
speed could damage the
blade and/or the saw.

(Figure 14) in the "

CLOSED

"

Figure 12. Engine Fuel Valve Lever

PAGE 20 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — INITIAL START-UP/OPERATION

5. Rotate the
and
engine governor speed is factory set to ensure optimum
blade operating speeds.

6. Grasp the starter grip (Figure 16) and slowly pull it out. The
resistance becomes the hardest at a certain position, corre­sponding to the compression point. Pull the starter grip briskly
and smoothly for starting.

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

throttle lever

slow

for starting. All sawing is done at

Figure 15. Throttle Lever

(Figure 15) halfway between

full throttle

fast

. The

8. Before the saw is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guards and/or covers.

OPERATION

1. Start the engine. Rotate the throttle lever (Figure 14) toward
full throttle.

WARNING

ALWAYS cut with the saw at FULL THROTTLE. Attempting to

cut with the saw at less than full throttle could cause the blade to
bind or stop abruptly in the slab resulting in serious injury to the
operator or others in the area.

WARNING

ALWAYS keep clear of

this equipment.

2. To begin sawing, lower the rotating blade allowing it to cut to
the preset depth.

rotating

or

moving

parts while operating

DO NOT pull the starter rope all the way to
the end. DO NOT release the starter rope
after pulling. Allow it to rewind as soon as
possible.

Figure 16. Starter Grip

7. If the engine has started, slowly return the choke lever
(Figure 14) to the
started repeat steps 1 through 6.

"OPEN"

position. If the engine has not

3. When blade has reached full cutting depth, slowly walk
behind the saw at a rate that will allow the engine to operate
without losing optimum RPM.

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

NOTE

4. When the end of the cut has been reached, raise the blade
out of the cut by pulling back on the handlebars (using a
downward pressure) until the raise/lower rod drops into its
slot with the blade in the raised position.

5. If cutting is complete, turn the engine off and wait for the blade
to stop rotating.

DO NOT try to cut faster than the blade will
allow. Cutting too fast will cause the blade to
rise up out of the cut. Improper cutting rate
can decrease the life of the engine and
blades.

Mark the cutting line clearly and always
saw in a STRAIGHT LINE ONLY.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 21

STOW CUTTER 1 SAW — MAINTENANCE

MAINTENANCE

See the engine manual supplied

NOTE

with your machine for appropriate
engine maintenance schedule and
troubleshooting guide for problems.

CAUTION!CAUTION!

CAUTION!

CAUTION!CAUTION!

ALWAYS allow the engine to
cool before servicing. NEVER
attempt any maintenance

hot!

work on a

engine.

WARNING

ALWAYS ensure that the engine ON/
OFF switch is in the "OFF" position,

(power cable UNPLUGGED on electric
models), and that the arbor shaft has

COMPLETELY STOPPED ROTATING

before performing any of the following
operations:

3. Adjust the front pointer wheel so it just touches the side of the
straightedge or level.

4. Remove the straightedge or level.

5. Position the front pointer and blade directly over the chalk
line.

6. Start the saw and lower the blade onto the chalk line.

7. Begin cutting and make sure the blade follows the chalk line
as closely as possible.

8. The pointer should follow the chalk line as well. If it does not,
adjust the pointer by loosening then tightening the jam nuts
on the pointer until the pointer follows the same path as the
blade.

Chassis Lubrication

■

Blade Shaft Bearings - Two zerk fittings are located at
the lower-front area of the saw. Lubricate before daily
use. Use a good quality automotive or general purpose
grease. Check and lubricate more often if unit is under
heavy use. Do not overfill bearings. Overfilling can
damage the grease seals which can result in bearing
exposure to dirt and contaminants which can then shorten
the life of the bearings. Excess grease can also drip onto
the cutting surface.

■

REMOVING

■

ADJUSTING

■

LUBRICATING

■

REMOVING

■

INSPECTING, ADJUSTING, OR REPLACING

belt, arbor shaft, arbor shaft bearings or
part

Saw Blade Removal and Installation

Saw blade removal and installation is covered on page 19.

Front Pointer Adjustment

The front pointer wheel has been set at the factory. Use these
procedures only if the pointer is suspect of being out of alignment.

1. Chalk out a straight line on the prepared slab or cutting
surface.

2. Use a 4 foot straightedge or level by placing it flat against the
blade.

or

INSTALLING

front or rear pointers

any components

engine mounting bolts

blades

ANY

drive-

engine

Drive Belt

Refer to pages 16 and 17 of this manual for Drive Belt adjustment
procedures and Removal and Replacement procedures.

Engine

Follow the maintenance procedures outlined in the engine
owner's manual.

Engine Oil Change

Drain the used oil while the engine is warm by the following:
Refer to Figure 17.

1. Place an oil pan or suitable container below the engine drain
plug to catch the used oil.

2. Remove the filler cap/dipstick and the drain plug.

3. Drain the oil completely and reinstall the drain plug. Ensure
the drain plug is tightened securely.

PAGE 22 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — MAINTENANCE

Dispose of used oil properly. DO
NOT pour used oil on the ground,

NOTE

4. Make sure the engine is in a level position and fill to the outer
edge of the oil filler hole with the recommended oil. (See
Table 4.) Engine oil capacity is 1.16 US quart (1.1 liter).

5. Screw in the filler cap/dipstick securely.

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

Running the engine with a low oil level can
cause engine damage.

down a drain, or throw in the trash.
Used oil can generally be taken to
your local recycling center or
service station for reclamation.

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 23

Figure 17. Engine Oil Change

STOW CUTTER 1 SAW — TROUBLESHOOTING (SAW)

GNITOOHSELBUORTEDALB.5ELBAT

MOTPMYS MELBORPELBISSOP NOITULOS

gnieblairetamehtrofdrahootedalB

?tuc

foesuacebdehsinimideuqrotenignE

?tleb-Vesool

.gnittucspotsroswolsedalB

thgiartstuctonseodedalB

.eurtro/dna

?gnittuc

?rewopenignetneiciffusnI .rewopesrohenignEkcehC.gnitteselttorhtkcehC

?tucgnieblairetam

?segnalfdnasredluohs

?noitatorfonoitceridreporpmI

?tfahsedalbehtnognippilssiedalB

?wasdengilasimnodesugniebedalB .ytirgetnitnemngiladnasgniraebtfahsedalbkcehC

ehtrofdrahylevissecxesiedalB

?MPRreporpmitadesugniebedalB

robranodetnuomylreporpmiedalB

elihwedalbotdeilppaecrofevissecxE

TONOD dnawolsaylppA.tucehtniedalbehtecrof

.edalbeht"sserdeR"

.stleB-Vecalperro/dnanethgiT

.noitcerid"gnittuC-nwoD"anistniopworra

.tfahsedalbeht

.000,6yletamixorppa

.gniwasnehwecapydaets

gnittucyrT.edalbtcerrocrofpiuqitluMrorelaeDtlusnoC

ot)kcolbrednic,kcirbacilis,enotsdnas(lairetamtfosyrev

lanoitatordnadetneiroylreporpsiedalbehttahtkcehC

nodellatsniylreporperanipegnalf&edalbehttahtkcehC

gnieblairetamehthtiwedalbehtfonoitacificepskcehC

.noitamrofnirofpiuqitluMrorelaeDtlusnoC.tuc

si)MPFS(deepsetunimrepteefecafrusedalberusnE

.tfahsedalbehtnodexiffaylreporpsiedalberusnE

gnieblairetamehtrofdrahootsedalB

?tuc

robranodetnuomylreporpmiedalB

?segnalfdnasredluohs

gniloochguonegniviecertonedalB

gnilkcarc,gnirolocsidedalB

.ylevissecxegniraewro/dna

?riaroretaw

?dnuorfotuoelohrobrA .tfahsedalbehtnodexiffaylreporpsiedalberusnE

lairetamrofnesohcedalbtcerrocnI

?tucgnieb

?gnittuc

ev

.edalbeht"sserdeR"

.edalbgnittucyrdatuoba

elihwedalbotdeilppaecrofevissecxE

TONOD dnawolsaylppA.tucehtniedalbehtecrof

.gniwasnehwecapydaets

gnittucyrT.edalbtcerrocrofpiuqitluMrorelaeDtlusnoC

ot)kcolbrednic,kcirbacilis,enotsdnas(lairetamtfosyr

.tfahsedalbehtnodexiffaylreporpsiedalberusnE

tewrofdedivorpsiretawfoemulov&wolfreporperusnE

detalucricsiriagnilooctneiciffuserusnE.sedalbgnittuc

gnieblairetamehthtiwedalbehtfonoitacificepskcehC

.noitamrofnirofpiuqitluMrorelaeDtlusnoC.tuc

PAGE 24 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — TROUBLESHOOTING (ENGINE)

)ENIGNE(GNITOOHSELBUORT.6ELBAT

MOTPMYSESUACELBISSOPNOITULOS

?gnigdirbgulpkrapS

?gulpkrapsnotisopednobraC .gulpkrapsecalperronaelC

ontub,elbaliavasileuf",tratsottluciffiD

."gulpkrapstaKRAPS

dna,elbaliavasileuf",tratsottluciffiD

eserpsiKRAPS

."gulpkrapsehttatn

?noitalusni

?gnitiucric

ifedoteudtiucrictrohS

?paggulpkrapsreporpmI.pagreporp

?evitcefedliocnoitingI.liocnoitingiecalpeR

?detrohssihctiwsFFO/NO

ronekorberiwgulpkrapS

?epytleufgnorW

gulpkrapstneic

.nrowfiecalper

otteS

.hctiws

?ytridstniop,pagkrapsreporpmI

trohsronrownoitalusniresnednoC

?gnitiucrictrohs

.stniopnaelc

.gniriw

ronoitalusni,pagkcehC

.gulpkrapsecalper

,noitalusnigulpkrapskcehC

ecalper,gniriwhctiwskcehC

krapstcerrocteS

dnapag

.resnednocecalpeR

gulpkrapsevitcefedecalpeR

ecalperdna,metsysleufhsulF

.leuffoepyttcerrochtiw

kraps,elbaliavasileuf",tratsottluciffiD

inoisserpmocdnatneserpsi

ileuf",tratsottluciffiD

."lamrons

kraps,elbaliavas

."wolsinoisserpmocdnatneserpsi

.roterubracehttatneserpleufoN

udroretaW.metsysleufhsulF

?ytridrenaelcriA .renaelcriaecalperronaelC

?nepOekohC.ekohCesolC

denethgit

?degamad

?ylreporp

?deggolcretlifleuF.retlifleufecalpeR

enilleufniriA.enilleufdeelB

?

?metsysleufnits

?nrowrednilycro/dnagnirnotsiP

tongulpkrapsro/dnadaehrednilyC

teksaggulpkrapsro/dnateksagdaeH

?deggolcelohrehtaerbpacknatleuF .packnatleufecalperronaelC

eR

?dedurtorprokcutsevlavtsuahxe/noitcuS.sevlavtaes-

?)ypmeknat(knatleufnielbaliavatonleuF .leuffoepyttcerroc

ro/dnasgnirnotsipecalpeR

.notsip

dnastlobdaehrednilyceuqroT

.gulpkraps

gulpkrapsro/dnadaehecalpeR

.steksag

htiwlliF

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 25

STOW CUTTER 1 SAW — TROUBLESHOOTING (ENGINE)

)DEUNITNOC,ENIGNE(GNITOOHSELBUORT.6ELBAT

MOTPMYSESUACELBISSOPNOITULOS

?naelctonrenaelcriA .renae

reporpsinoisserpmoc"rewopnikaeW"

.erifsimtonseoddna

tcefeD .gulpkrapsecalperronaelC

reporpsinoisserpmoc"rewopnikaeW"

ifsimtub

.ser

.staehrevoenignE

?gulpkrapsevi

?paggulpkrapsreporpmI.pagreporpotteS

?metsysleufniretaW

?evitcefedliocnoitingI.liocnoit

?gulpkrapsytriD .gulpkrapsecalperronaelC

?epytleufgnorW

?roterubracnilevelleufreporpmI

ingiecalpeR

hsulF

?reporpmieulavtaehgulpkrapS

.gulpkraps

lcriaecalperronaelC

.tnemtsujdataolfkcehC

.roterubracdliubeR

ecalperdnametsysleufhsulF

.leufepyttcerrochtiw

ecalperdna,metsysleuf

.leuffoepyttcerrochtiw

foepyttcerrochtiwecalpeR

looC.snifgniloocnaelC

.setautculfdeepslanoitatoR

.noitc

nuflamretratslioceR

?trid

irpslaripS.gnirpslaripsecalpeR

?ytridsnifgni

?yltcerrocdetsujdaronrevoG.ronrevogtsujdA

efedgnirpsronrevoG.gnirpsronrevogecalpeR

?detcirtserwolfleuF

?esoolgn

?gnissimroevitc

rofmetsysleuferitnekcehC

.sgolcroskael

dnatsudhtiwdeggolcmsinahcemlioceR

.retawdna

paoshtiwylbmessaliocernaelC

PAGE 26 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

NOTE PAGE

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 27

EXPLANATION OF CODE IN REMARKS COLUMN

How to read the marks and remarks used in this parts
book.

NOTE

Items Found In the “Remarks” Column

Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.

Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.

Items Found In the “Items Number” Column

All parts with same symbol in the number column,

■

, belong to the same assembly or kit.

Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.

If more than one of the same

NOTE

reference number is listed, the
last one listed indicates newest
(or latest) part available.

, #, +, %, or

*

The contents of this parts
catalog are subject to change
without notice

.

PAGE 28 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — SUGGESTED SPARE PARTS

SUGGESTED SPARE PARTS

STOW CUTTER 1 SAW CONCRETE/ASPHALT SAW

1 TO 3 UNITS WITH HONDA GX390K1QWT2 ENGINE
AND 5HP ELECTRIC MOTOR.

1 to 3 Units

Qty. ..... P/N ........................ Description

3 ...........20478 ................... HAND GRIP

4 ...........2621 ..................... GREASE ZERK, SPINDLE BRNG

4 ........... 1162 A .................. CAP, GREASE ZERK

3 ...........13249 ................... BELT (3VX315) 13HP HONDA

3 ...........16779-006 ............ BELT (3VX300) 5HP ELECTRIC MOTOR

3 ...........9807956846 ......... SPARK PLUG HONDA

1 ...........17620ZH7023 ...... TANK CAP (HONDA)

2 ...........17210ZE2505 ...... AIR CLEANER ELEMENT

1 ...........28462ZV7003 ...... ROPE, RECOIL STARTER

NOTE

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 29

The contents of this parts catalog
are subject to change without
notice.

DECALS

STOW CUTTER 1 SAW — NAMEPLATE AND DECALS

PAGE 30 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — NAMEPLATE AND DECALS

NAMEPLATE AND DECALS

NO. PART NO. PART NAME QTY. REMARKS

1 25215-001 DECAL, WARNING.......................... 1 .......... ELECTRIC MODEL ONLY

2 28997-001 DECAL, PROP 65 WARNING 1
3 13118 DECAL, POWDER COATED 1
4 22972-003 DECAL, STOW 6.00 1
5 23653-001 DECAL, STOW CUTTER 1 SAW 1

6 SERIAL NUMBER PLATE ............... 1 .......... CONTACT PARTS DEPT.

7 22122-001 DECAL, WARNING 1
8 25250-001 DECAL, WARNING FEET 1
9 22972-004 DECAL, STOW 7.00 1
10 23330-001 DECAL, CAUTION BLADE GUARD 1
11 25491 DECAL, ROTATION 1
12 25249-001 DECAL, WARNING HANDS 1
13 11246 DECAL SHEET, INTL STDS. 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 31

STOW CUTTER 1 SAW — ENGINE, BELTS AND PULLEYS ASSY.

ENGINE, BELTS AND PULLEYS ASSY.

PAGE 32 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — ENGINE, BELTS AND PULLEYS ASSY.

ENGINE, BELTS AND PULLEYS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 15103 ENGINE 13 HP HONDA CYCLONE 1
3 0669 A SCREW. HHCS 5/16-18 x 2-1/4" 4
4 0300 B FLAT WASHER 5/16" 10
5 5283 NUT, 5/16 - 18 LOCK 4
6 23811-352 BELT TENSIONER 2
7 6059 B SQUARE KEY, 1/4 X 2 1
8 23665-001 PULLEY, ENGINE 1
9 25354 SCREW, SHS 1/4 - 20 X 1/2 ALLOY4
10 13249 BELT, 3VX315 3
11 23665-009 PULLEY, SPINDLE 1
12 27044-001 SPACER 2
13 26105-351 BELT GUARD, 13HP 1
14 0202 SCREW, 5/16 - 12 X 1 2
15 161 C WASHER, LOCK 5/16 2
16 26112-354 FRAME 1
17 9152 KEY, 1/4 X 1-3/4 1
18 10779-011 CAP 2
19 10133 NUT, 3/8 - 16 2
20 10136 WASHER, FLAT 3/8 2

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 33

ELECTRIC MOTOR ASSY.

2

STOW CUTTER 1 SAW — ELECTRIC MOTOR ASSY.

1

3

8

9

4

10

11

5

7

11

13

6

PAGE 34 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

12

STOW CUTTER 1 SAW — ELECTRIC MOTOR ASSY.

ELECTRIC MOTOR ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 26142-352 BELT GUARD 1
2 16779-006 BELT - 3VX300 3
3 23665-005 PULLEY (MOTOR) 1
4 26152-502 MOTOR, 5 HP ELECTRIC 1
5 27084-002 SPACER 2
6 23665-009 PULLEY (SPINDLE) 1
7 26145-351 FRAME 1
8 25215-001 LABEL, WARNING 1
9 23865-001 SCREW, 10 - 24 X 3/4 2
10 2623 SCREW, HHC 5/16 -18 x 1-1/4" 4
11 07030-005 FLAT WASHER 5/16 8
12 26136-004 SPINDLE 1
13 5283 NUT, 5/16 - 18 LOCK 4

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 35

UNDERCARRIAGE ASSY

STOW CUTTER 1 SAW — UNDERCARRIAGE ASSY.

1

3

5

2

4

11

10

8

14

7

9

16

6

12

13

3

15

ORDERABLE AS ASSEMBLY

1

P/N 23666-001 OR SEPARATELY;
BEARING P/N 11149,
CLAMP P/N 11138.

24

20

19

23

18

28

20

19

17

16

21

22

18

23

14

28

25

1

26

PAGE 36 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

29

28

27

28

27

STOW CUTTER 1 SAW — UNDERCARRIAGE ASSY.

UNDERCARRIAGE ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 08233-005 LOCKNUT, 5/16 - 18 1
2 18637-001 KNOB 1
3 0161 D HEX NUT, 5/16 - 18 3
4 25496 BUSHING 1
5 28808-002 CRANK HANDLE 1
6 26164-001 LOCK PIN 1
7 4568 ROLL PIN 3/16 X 1 1
8 07046-011 BOLT, CARRIAGE 5/16-18 X 1-1/2 2
9 23284-001 WRAPPER-BLADE GUARD 1
10 20478 HAND GRIP 2
11 26126-352 HANDLE 1
12 0300 B FLAT WASHER 5/16 2
13 0161 C LOCK WASHER 5/16 2
14 1162 A CAP, GREASE ZERK 4
15 26137-002 ACME SCREW 1
16 2621 ZERK, GREASE STR 1/4 - 28 1
17 29408-352 JACK ARM (SUPPORT TUBE) 1
18 0205 SCREW, HHCS 3/8 - 16 X 1-1/4 8
19 0166 A LOCK WASHER, 3/8 8
20 10136 FLAT WASHER 3/8 8
21 6014 B COTTER PIN 3/32 X 1 1
22 08326-019 PIN 3/8 X 2-5/16 1
23 07402-024 ROLL PIN 1/8 X 1-1/2 2
24 26120-352 WHEEL BASE ASSEMBLY 1
25 23666-001 CLAMP & BEARING ASSEMBLY 2
25A 11138 CLAMP ASSEMBLY 2
25B 11149 BEARING 2
26 23668-001 REAR WHEEL, (6 X 2) 2
27 26133-001 LOCKING COLLAR 4
28 8151 FLAT WASHER, 3/4 6
29 26121-001 FRONT WHEEL 2

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 37

STOW CUTTER 1 SAW — WATER SYSTEM & BLADE ASSY.

WATER SYSTEM & BLADE ASSY.

1

2

3

4

5

28

27

6

26

26

25

25

24

23

7

19

20

18

17

16

16

10

9

4

8

21

2

12

11

13

15

14

3

2

22

30

29

31

41

PULLEY ASSEMBLY.

1

SEE PAGE 30.

PAGE 38 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

37

40

32

33

26

34

35

36

38

30

37

39

40

35

Multiquip Diamond Back Blades

ORDER p/n

9SWG

1

STOW CUTTER 1 SAW — WATER SYSTEM & BLADE ASSY.

WATER SYSTEM & BLADE ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 22129-001 CLAMP 2
2 0948 FLAT WASHER, 1/4 5
3 0181 B LOCK WASHER 1/4 5
4 0949 HEX NUT 1/4 - 20 5
5 0424 SCREW, HHCS 1/4 - 20 X 1 4
6 29406-352 BLADE GUARD 1
7 18626-001 SPRING 2
8 23255-011 HOSE 26" 1
9 23566-001 BARBED FITTING 90 DEG. 1
10 35122-402 VALVE 1
11 11708 NIPPLE 1/2 1
12 16378-005 U-BOLT 1/4 1
13 23252-002 ELBOW 1/2 1
14 15544 CONNECTOR, GARDEN HOSE 1
15 13336-001 WASHER, RUBBER 1
16 12694-006 HOSE CLAMP 2
17 24778-001 SWIVEL CONNECTOR 1
18 24642-001 Y-FITTING 1
19 12694-004 HOSE CLAMP 2

20 60021 .............. HOSE, 1.0 FT. ................................. 2 .......... SOLD PER FOOT

21 0131 A SCREW, HHCS 1/4 - 20 X 3/4 2
22 28729-005 CHIP GUARD 1
23 10930 FENDER WASHER 1/4 2
24 10024 LOCKNUT, 1/4 - 20 2
25 10136 FLAT WASHER 3/8 6
26 0166 A LOCK WASHER 3/8 2
27 06501-032 SCREW, HHCS 3/8 - 16 X 4 1
28 0205 SCREW, HHCS 3/8 - 16 X 1 1
29 06922-003 NUT L.H. 1 - 1/4 1
30 15046 DOWEL PIN 3/8 X 1-1/4 2
31 26928-004 FLANGE, OUTER 1
32 28811-001 FLANGE, INNER 1
33 4001 FLAT WASHER 4
34 1284 SCREW, HHCS 3/8 - 16 X 1-1/2 4
35 3200 BEARING 2
36 0125 WOODRUFF KEY 1/4 X 1 1
37 1162 A CAP, GREASE ZERK 2
38 26135-002 SPINDLE 1
39 9152 KEY 1/4 X 1-3/4 1
40 2621 GREASE ZERK 2
41 9SWG BLADE, DIAMOND BACK 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 39

POINTER ASSY.

STOW CUTTER 1 SAW — POINTER ASSY.

PAGE 40 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

STOW CUTTER 1 SAW — POINTER ASSY.

POINTER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1
2
3
4
5
6
7

8 29042-501 INDICATOR ASSEMBLY ................. 1 .......... INCLUDES ITEMS W/

21017 SCREW, POINTER ARM 1

*

29043-001 WHEEL, POINTER 1

*

1007 NUT, HEX JAM 3/8 - 16 2

*

1456 NUT, HEX FINISH 3/8 - 16 2

*

10133 NUT, NYLOC 3/8 - 16 2

*

27073-001 ARM, POINTER 1

*

10136 WASHER, FLAT 3/8 2

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 41

AIR CLEANER ASSY.

HONDA GX390K1QWT2 ENGINE — AIR CLEANER ASSY.

PAGE 42 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — AIR CLEANER ASSY.

AIR CLEANER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 16271ZE2000 GASKET, ELBOW 1

2 17210ZE3010 ELEMENT, AIR CLEANER ........................ 1 ......... INCLUDES ITEMS W/

2 17210ZE3505 ELEMENT, AIR CLEANER ........................ 1 ......... INCLUDES ITEMS W/

3
4
5 17230ZE3841 COVER, AIR CLEANER (CYCLONE) 1
6
7
8

9 17410ZE3840 ELBOW, AIR CLEANER ............................. 1 ......... INCLUDES ITEMS W/

10 17470ZE3841 CASE, PRE AIR CLEANER 1
11 17475ZE3841 CAP, PRE AIR CLEANER 1
12 17476ZE3841 GUIDE, PRE AIR CLEANER 1
13 90142MB0000 SCREW, PAN 5X16.5 5
14 90325044000 WINGNUT, TOOL BOX SETTING 2
15 90009ZE2003 BOLT- WASHER 6X22 1
16 0405006000 NUT, FLANGE 6MM 2

17218ZE3505 FILTER, OUTER 1

*

# 17219HA2405 SEAL, AIR CLEANER COVER 1

17232891000 GROMMET, AIR CLEANER 1

*

# 17238ZE2310 COLLAR, AIR CLEANER 2
# 17239ZE3840 COLLAR B, AIR CLEANER 1

*
*

#

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 43

CAMSHAFT ASSY.

HONDA GX390K1QWT2 ENGINE — CAMSHAFT ASSY.

PAGE 44 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CAMSHAFT ASSY.

CAMSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 14100ZF6W01 CAMSHAFT ASSEMBLY .......................... 1 ......... INCLUDES ITEM W/

2 14410ZE3013 ROD, PUSH 2
3 14431ZE2010 ARM, VALVE ROCKER 2
4 14441ZE2000 LIFTER, VALVE 2
5 14451ZE1013 PIVOT, ROCKER ARM 2
6
7 14711ZE3000 VALVE, INTAKE 1
8 14721ZE3000 VALVE, EXHAUST 1
9 14751ZE2003 SPRING, VALVE 2
10 14771ZE2000 RETAINER,INTAKE VALVE SPRING 1
11 14773ZE2000 RETAINER, EXHAUST VALVE SPRING 1
12 14775ZE2010 SEAT, VALVE SPRING 1
13 14781ZE2000 ROTATOR, VALVE 1
14 14791ZE2010 PLATE, PUSH ROD GUIDE 1
15 90012ZE0010 BOLT, PIVOT 8MM 2
16 90206ZE1000 NUT, PIVOT ADJ. 2
17 12209ZE8003 SEAL, VALVE STEM 1

14568ZE1000 SPRING, WEIGHT RETURN 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 45

CARBURETOR ASSY.

HONDA GX390K1QWT2 ENGINE — CARBURETOR ASSY.

PAGE 46 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CARBURETOR ASSY.

CARBURETOR ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1

#+ 16010ZE2812 GASKET SET 1

*

2

*

3

*

4

*

5

*

6

+ 16024ZE1811 SCREW SET, DRAIN ........................... 1 ............. INCLUDES ITEM W/#

*

7

*

8

*

9 16100ZF6V21 CARBURETOR ASSY. (BE85C B) ....... 1 ............. INCLUDES ITEMS W/

10

*

11

*

12

*

13 16211ZF6000 INSULATOR, CARBURETOR 1
14 16220ZA0702 SPACER, CARBURETOR 1
15 16221ZF6800 GASKET, CARBURETOR 1
16 16223ZE3W00 GASKET, INSULATOR 1

20 16610ZE1000 LEVER, CHOKE (STD) ........................1 ............. INCLUDES ITEM W/$

22

*

23

*

24

*

25

*

26

*

28

*

31$ 9430520122 PIN, SPRING (2X12) 1
33

*

33 99101ZH80980 JET, MAIN (#98) (OPTIONAL) 1
33

*

34

*

35

*

16011ZA0931 VALVE SET, FLOAT 1
16013ZA0931 FLOAT SET 1

16015ZE8005 CHAMBER SET, FLOAT ...................... 1 ............. INCLUDES ITEMS W/+

16016ZH7W01 SCREW SET 1

16028ZE0005 SCREW SET B .................................... 1............. INCLUDES ITEM W/#

16044ZE3W20 CHOKE SET 1

16124ZE0005 SCREW, THROTTLE STOP 1
16166ZF6W10 NOZZLE, MAIN 1
16173001004 GASKET, FUEL STRAINER CUP 1

16953ZE1812 LEVER, VALVE 1
16954ZE1812 PLATE, LEVER SETTING 1
16956ZE1811 SPRING, VALVE LEVER 1
16957ZE1812 GASKET, VALVE 1
16967ZE0811 CUP, FUEL STRAINER 1
93500030060H SCREW, PAN (3X6) 2

99101ZH80950 JET, MAIN (#95) (OPTIONAL) 1

99101ZH81000 JET, MAIN (#100) 1

99204ZA00450 JET SET, PILOT (#45) ......................... 1 ............. INCLUDES ITEM W/#

16172ZE3W10 COLLAR, SET 1

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 47

CONTROL ASSY.

HONDA GX390K1QWT2 ENGINE — CONTROL ASSY.

PAGE 48 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CONTROL ASSY.

CONTROL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 16551ZE3000 ARM, GOVERNOR 1
3 16555ZE3000 ROD, GOVERNOR 1
4 16561ZE3000 SPRING, GOVERNOR 1
5 16562ZE3000 SPRING, THROTTLE RETURN 1

6 16570ZE3W20 CONTROL ASSY. (REMOTE) .................... 1 ......... INCLUDES ITEMS W/

10
11
12
13
14
15
17
18
21 90013883000 BOLT, FLANGE (6X12) (CT200) 2
22 90015ZE5010 BOLT, GOVERNOR ARM 1
24
27
28
29 9405006000 NUT, FLANGE (6MM) 1

16571ZE3W00 LEVER, CONTROL 1

*

16574ZE1000 SPRING, LEVER 1

*

16575ZE2W00 WASHER, CONTROL LEVER 1

*

16576891000 HOLDER, CABLE 1

*

16578ZE1000 SPACER, CONTROL LEVER 1

*

16581ZE3W00 BASE, CONTROL 1

*

16584883300 SPRING, CONTROL ADJUSTING 1

*

16592883310 SPRING, CABLE RETURN 1

*

90114SA0000 NUT, SELF-LOCK (6MM) 1

*

93500050320A SCREW, PAN (5X32) 1

*

93500050160A SCREW, PAN (5X16) 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 49

CRANKCASE COVER ASSY.

HONDA GX390K1QWT2 ENGINE — CRANKCASE ASSY.

PAGE 50 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CRANKCASE ASSY.

CRANKCASE COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 11300ZE3602 COVER ASSY., CRANKCASE (Q-TYPE) ......... 1 ................ INCLUDES ITEMS W/

3 11381ZE3801 GASKET, CASE COVER 1

4 15600ZG4003 CAP ASSY., OIL FILLER .................................1 ................ INCLUDES ITEM W/#

5 15600735003 CAP ASSY., OIL FILLER .................................1 ................ INCLUDES ITEM W/#

8# 15625ZE1003 GASKET, OIL FILLER CAP 2

9 16510ZE3000 GOVERNOR ASSY. .......................................... 1 ................ INCLUDES ITEMS W/+

10

+ 16511ZE8000 WEIGHT, GOVERNOR 3

*

11

+ 16512ZE3000 HOLDER, GOVERNOR WEIGHT 1

*

12

+ 16513ZE2000 PIN, GOVERNOR WEIGHT 3

*

13

*

13

*

15

*

16 90701HC4000 PIN, DOWEL (8X12) 2
17

*

18

*

19 957010804000 BOLT, FLANGE (8X40) 7
20

*

21

*

16531ZE2000 SLIDER, GOVERNOR 1
16531Z0A000 SLIDER, GOVERNOR 1
90602ZE1000 CLIP, GOVERNOR HOLDER 1

91201ZE3004 OIL SEAL (35X52X8) 1
9410106800 WASHER, PLAIN (6MM) 1

961006202000 BEARING, RADIAL BALL (6202) 1
961006207000 BEARING, RADIAL BALL (6207) 1

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 51

CRANKSHAFT ASSY.

HONDA GX390K1QWT2 ENGINE — CRANKSHAFT ASSY.

PAGE 52 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CRANKSHAFT ASSY.

CRANKSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 13310ZF6W10 CRANKSHAFT (Q-TYPE).......................... 1 ......... INCLUDES ITEM W/

8 13351ZE3010 WEIGHT, BALANCER 1
11 90745ZE2600 KEY(6.3X6.3X43) 1
12

91001ZF6003 BEARING, RADIAL BALL (6207S) 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 53

HONDA GX390K1QWT2 ENGINE — CYLINDER BARREL ASSY.

CYLINDER BARREL ASSY.

PAGE 54 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CYLINDER BARREL ASSY.

CYLINDER BARREL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 12000ZF6W13 CYLINDER ASSY. (ALERT)....................... 1 ......... INCLUDES ITEMS W/

2 15510ZE2043 SWITCH ASSY., OIL LEVEL 1
4 16541ZE3010 SHAFT, GOVERNOR ARM 1
9 90131896650 BOLT, DRAIN PLUG 2
10 90446KE1000 WASHER (8.2X17X0.8) 1
12
13
14 91353671003 O-RING (13.5X1.5) (ARAI) 1
17 9405010000 NUT, FLANGE (10MM) 1
18 9410912000 WASHER, DRAIN PLUG (12MM) 2
19 9425110000 PIN, LOCK (10MM) 1
20 957010601200 BOLT, FLANGE (6X12) 2
21
22 34150ZH7003 ALERT UNIT, OIL 1
23 90013883000 BOLT, FLANGE (6X12) (CT200) 1

91201ZE3004 OIL SEAL (35X52X8) 1

*

91201ZE9003 OIL SEAL (8X14X5) 1

*

961006202000 BEARING, RADIAL BALL (6202) 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 55

CYLINDER HEAD ASSY.

HONDA GX390K1QWT2 ENGINE — CYLINDER HEAD ASSY.

PAGE 56 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — CYLINDER HEAD ASSY.

CYLINDER HEAD ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 12200ZF6W01 CYLINDER HEAD ............................................. 1 ................ INCLUDES ITEMS W/

2
3
4
5 12251ZF6W00 GASKET, CYLINDER HEAD 1
6 12310ZE3791 COVER, HEAD 1
7 12315ZE3840 TUBE, BREATHER 1
8 12391ZE2020 GASKET, CYLINDER HEAD COVER 1
10 17316611000 CLIP, BREATHER TUBE 2
11 90014ZE2000 BOLT, HEAD COVER 1
12 90042ZE8000 BOLT, STUD (8X131.5) 2
13 92900080320E BOLT 2, STUD (8X32) 2
14 90441ZE2010 WASHER, HEAD COVER 1
16 9430112200 PIN A, DOWEL (12X20) 2
17 957011008000 BOLT, FLANGE (10X80) 4
18 9807955846 SPARK PLUG (BPR5ES) (NGK) (OPT.) 1
18 9807956846 SPARK PLUG (BPR6ES) (NGK) 1

12204ZE2306 GUIDE, VALVE (OS) (OPTIONAL) 1

*

12205ZE2305 GUIDE, EX. VALVE (OS) (OPTIONAL) 1

*

12216ZE2300 CLIP, VALVE GUIDE 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 57

FAN COVER ASSY.

HONDA GX390K1QWT2 ENGINE — FAN COVER ASSY.

PAGE 58 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — FAN COVER ASSY.

FAN COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

4 16731ZE2003 CLIP, TUBE 1
7 19610ZE3010ZB COVER, FAN *NH1* (BLACK) 1
10 19631ZE3W00 SHROUD 1
13 36100ZH7003 SWITCH ASSY., ENGINE STOP 1
15 90013883000 BOLT, FLANGE (6X12) (CT200) 6

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 59

FLYWHEEL ASSY.

HONDA GX390K1QWT2 ENGINE — FLYWHEEL ASSY.

PAGE 60 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — FLYWHEEL ASSY.

FLYWHEEL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 19511ZE3000 FAN, COOLING 1
3 28450ZE3W11 PULLEY, STARTER (SCREEN GRID) 1
7 31100ZE3701 FLYWHEEL 1
10 90201ZE3V00 NUT, SPECIAL (16MM) (1) 1
11 90741ZE2000 KEY, SPECIAL WOODRUFF (25X18) 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 61

FUEL TANK ASSY.

HONDA GX390K1QWT2 ENGINE — FUEL TANK ASSY.

PAGE 62 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — FUEL TANK ASSY.

FUEL TANK ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 16854ZH8000 RUBBER, SUPPORTER (107MM) 1
3 16955ZE1000 JOINT, FUEL TANK 1
6 17510ZE3010ZB TANK, FUEL *NH1* (BLACK) 1

8 17620ZH7023 CAP, FUEL FILLER ................................................ 1 ......... INCLUDES ITEM W/

9
15 91353671003 O-RING (13.5X1.5) (ARAI) 1
17 9405008000 NUT, FLANGE (8MM) 2
18 950014500360M BULK HOSE, FUEL (4.5X3000) (4.5X235) 1
20 9500202080 CLIP, TUBE (B8) 2
22 957010802500 BOLT, FLANGE (8X25) 2

17631ZH7003 GASKET, FUEL FILLER CAP 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 63

IGNITION COIL ASSY.

HONDA GX390K1QWT2 ENGINE — IGNITION COIL ASSY.

PAGE 64 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — IGNITION COIL ASSY.

IGNITION COIL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 30500ZF6W01 COIL ASSY., IGNITION 1
2 30700ZE1013 CAP ASSY., NOISE SUPPRESSOR 1
8 31512ZE2000 GROMMET, WIRE 1
12 36101ZE2701 WIRE, STOP SWITCH (430MM) 1
17 90015883000 BOLT, FLANGE (6X28) 2
18 90684ZA0601 CLIP, WIRE HARNESS 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 65

MUFFLER (1) ASSY.

HONDA GX390K1QWT2 ENGINE — MUFFLER ASSY.

PAGE 66 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — MEFFLER ASSY.

MUFFLER (1) ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 18310ZE2W61 MUFFLER 1
3 18320ZE2W61 PROTECTOR, MUFFLER 1
5 18330ZE2W00 PIPE, EX. 1
6 18331ZE3810 CAP, MUFFLER 1
7 18333ZF6W01 GASKET, EX. PIPE 1
8 18355ZE2W00 ARRESTER, SPARK (OPTIONAL) 1
9 18381ZE2W10 GASKET, MUFFLER (ARRESTER) (OPTIONAL) 1
10 18381ZE2800 GASKET, MUFFLER 1
19 90050ZE1000 SCREW, TAPPING (5X8) 4
22 90055ZE1000 SCREW, TAPPING (4X6) 3
27 90006ZE2000 SCREW, TAPPING (6X10) 1
28 9405008000 NUT, FLANGE (8MM) 5
31 90055ZE1000 SCREW, TAPPING (4X6) 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 67

PISTON ASSY.

HONDA GX390K1QWT2 ENGINE — PISTON ASSY.

PAGE 68 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — PISTON ASSY.

PISTON ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 13010ZF6003 RING SET, PISTON (STD) 1
1 13011ZF6003 RING SET, PISTON (OS 0.25) (OPTIONAL) 1
1 13012ZF6003 RING SET, PISTON (OS 0.50) (OPTIONAL) 1
1 13012ZF6005 RING SET, PISTON (OS 0.50) (OPTIONAL) 1
1 13013ZF6003 RING SET, PISTON (0.75) (NIPPON) 1
2 13101ZF6W00 PISTON (STD) 1
2 13102ZF6W00 PISTON (OS 0.25) (OPTIONAL) 1
2 13103ZF6W00 PISTON (OS 0.50) (OPTIONAL) 1
2 13104ZF6W00 PISTON (0.75) (OPTIONAL) 1
3 13111ZF6W00 PIN, PISTON 1

4 13200ZE3010 ROD ASSY., CONNECTING (STD) ........................ 1 ......... INCLUDES ITEM W/

4 13200ZE3315 ROD ASSY., CONNECTING(US 0.25) (OPT.) ........ 1 ......... INCLUDES ITEM W/

5
6 90601ZE3000 CLIP, PISTON PIN (20MM) 2

90001ZE8000 BOLT, CONNECTING ROD 2

*

*
*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 69

RECOIL STARTER ASSY.

HONDA GX390K1QWT2 ENGINE — RECOIL STATER ASSY.

PAGE 70 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — RECOIL STATER ASSY.

RECOIL STARTER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 28400ZE3W01ZB STARTER ASSY., RECOIL *NH1* (BLACK) .............. 1 ...... INCLUDES ITEMS W/

2
3
4
5
6
7
8
10
11
13
14 90008ZE2003 BOLT, FLANGE (6X10) 3

28410ZE3W01ZB CASE, RECOIL STARTER *NH1* (BLACK) 1

*

28421ZE3W01 PULLEY, RECOIL STARTER 1

*

28422ZE2W01 RATCHET, STARTER 2

*

28441ZE2W01 SPRING, FRICTION 1

*

28442ZE2W01 SPRING, STARTER RETURN 1

*

28443ZE2W01 SPRING, RATCHET 2

*

28444ZE2W01 RETAINER, SPRING 1

*

28461ZE2W02 GRIP, STARTER 1

*

28462ZV7003 ROPE, RECOIL STARTER 1

*

90004ZE2W01 SCREW, CENTER 1

*

*

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 71

LABELS ASSY.

HONDA GX390K1QWT2 ENGINE — LABELS ASSY.

PAGE 72 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

HONDA GX390K1QWT2 ENGINE — LABELS ASSY.

LABELS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 87521ZF6W01 EMBLEM 1
4 87522ZH9000 LABEL, CAUTION 1
7 87528ZE2810 MARK, CHOKE (EXTERNAL) 1
9 87532ZH8810 MARK, OIL ALERT (E) 1
12 87534ZE1841 LABEL, AIR CLEANER CAUTION 1
13 87535ZE1840 MARK, AIR CLEANER SALES POINT 1

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 73

Effective: October 1, 2002

TERMS AND CONDITIONS OF SALE — PART S

PAYMENT TERMS

Terms of payment for parts are net 10 days.

FREIGHT POLICY

All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.

MINIMUM ORDER

The minimum charge for orders from Mul­tiquip is $15.00 net. Customers will be asked
for instructions regarding handling of orders
not meeting this requirement.

RETURNED GOODS POLICY

Return shipments will be accepted and credit
will be allowed, subject to the following provi­sions:

1. A Returned Material Authorization must
be approved by Multiquip prior to ship­ment.

2. To obtain a Retur n Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quanti­ties, and descriptions of the items to be
returned.

a. The parts numbers and descriptions

must match the current parts price
list.

b. The list must be typed or computer

generated.

c. The list must state the reason(s) for

the return.

d. The list must reference the sales

order(s) or invoice(s) under which the
items were originally purchased.

e. The list must include the name and

phone number of the person request­ing the RMA.

3. A copy of the Return Material Authoriza­tion must accompany the return shipment.

4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.

5. Parts must be in new and resalable con-

6. The following items are not returnable:

7. The sender will be notified of any material

8. Such material will be held for five working

9. Credit on returned parts will be issued at

10. In cases where an item is accepted, for

11. Credit issued will be applied to future

PRICING AND REBATES

Prices are subject to change without prior
notice. Price changes are effective on a spe­cific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.

Multiquip reserves the right to quote and sell
dition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.

a. Obsolete parts. (If an item is in the

price book and shows as being re­placed by another item, it is obsolete.)

b. Any parts with a limited shelf life

(such as gaskets, seals, “O” rings,
and other rubber parts) that were pur­chased more than six months prior to
the return date.

c. Any line item with an extended dealer

net price of less than $5.00.

d. Special order items.

e. Electrical components.

f. Paint, chemicals, and lubricants.
g. Decals and paper products.

h. Items purchased in kits.

received that is not acceptable.

days from notification, pending instruc­tions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.

dealer net price at time of the original
purchase, less a 15% restocking charge.

which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.

purchases only.

direct to Government agencies, and to Original

Equipment Manufacturer accounts who use

our products as integral parts of their own

products.

SPECIAL EXPEDITING SERVICE

A $35.00 surcharge will be added to the invoice

for special handling including bus shipments,

insured parcel post or in cases where Multiquip

must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITY

Multiquip shall not be liable hereunder for

damages in excess of the purchase price of the

item with respect to which damages are

claimed, and in no event shall Multiquip be

liable for loss of profit or good will or for any

other special, consequential or incidental dam-

ages.

LIMITATION OF WARRANTIES

No warranties, express or implied, are made

in connection with the sale of parts or trade

accessories nor as to any engine not manufac-

tured by Multiquip. Such warranties made in

connection with the sale of new, complete units

are made exclusively by a statement of war-

ranty packaged with such units, and Multiquip

neither assumes nor authorizes any person to

assume for it any other obligation or liability

whatever in connection with the sale of its

products. Apart from such written statement of

warranty, there are no warranties, express,

implied or statutory, which extend beyond the

description of the products on the face hereof.

PAGE 74 — STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06)

NOTE PAGE

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #4 (05/31/06) — PAGE 75

OPERATION AND PARTS MANUAL

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING

PARTS DEPARTMENT

800-427-1244 or 310-537-3700
FAX: [phone] or 310-637-3284

SERVICE DEPARTMENT

800-421-1244
FAX: [phone]

TECHNICAL ASSISTANCE

800-478-1244
FAX: [phone]

WARRANTY DEPARTMENT

888-661-4279, or 310-661-4279
FAX: [phone]

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

A DIVISION OF MULTIQUIP INC.

POST OFFICE BOX 6254

CARSON, CA 90749
310-537-3700 • 888-252-STOW [888-252-7869]
FAX: [phone] • FAX: [phone]
E-MAIL: [e-mail] • WWW: stowmfg.com

PARTS DEPARTMENT:

800-427-1244
FAX: [phone]

SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:

800-478-1244
FAX: [phone]