STORM INTERFACE 5000 User Manual

5000 Series

Integrated Keypads

Integrated keypads with optional
display and card reader for industrial
or public environments

• Rugged, reliable and
responsive data entry

•Offered in shortened or extended
configuration (with or without
card reader option)

•Vandal Resistant
(20J BS EN 60068-2-75: 1997)

•Available with high impact
polymer or chromed metal keys

• Hardened stainless steel face plate

• Can be supplied with an (optional)
20 character x 4 line illuminated
LCD display

• Card reader/writer options
available to suit most applications

• Easily and securely installed

• Sealed against water and dust
to IP65 specification'

UK Email: [e-mail] Tel: [phone]
USA Email: [e-mail] Tel: [phone]

Storm Interface products include technology

protected by international patents and design

registration. All rights reserved.

www.storm-interface.com

5000 Series Integrated Keypads

003

Developed for use in a wide range of industrial and commercial applications, this integrated keypad with optional card reader and display
is ideal for use in exposed, hostile or public environments. The card reader and display type can be specified to suit most applications.
The optional LCD display module is securely located behind a coated, scratch resistant, water sealed polycarbonate window. Generous
provision is made for the location of interface and encoding circuitry on the rear face of the Keypad.

The FT Integrated keypad can also be specified with the unique Storm ‘Graphics’ keytop
technology. These innovative keytops enable customisation of keytop characters and colours
(even in low quantities). Please refer to the Storm K Range ‘Graphics Series’ keypads
datasheet for more information about Storm’s ‘Graphics’ keytop technology.

• Weather and vandal resistant for

outdoor and unsupervised public
environments

• Integrated hybrid card

reader-writer optional

• Optional 20 Character x 4 Line,

illuminated LCD display
(LCD Graphic or Vacuum
Fluorescent displays available)

• Rapid, responsive and reliable

data entry

• Stainless Steel front plate

• Available with High Impact Polymer

or Chromed Metal keys

214.00 or 169.00

• Easily and securely installed in

vending machines, car-wash
controllers, public telephones,
ticketing machines, gasoline pumps
and car-parking control equipment.

Electrical

Contact Bounce 5ms (max)
Contact Resistance 100 ohms (max)
Insulation Resistance 50 Mohms (min)
Breakdown Voltage 500V AC (max 60 secs.)
Operating Voltage 24V DC (max)
Operating Current 50mA (max)

Mechanical

Operational Life 4 million cycles (min) per key
Keytop Travel 1.4mm nominal
Actuation Force 180gms nominal
Connector 0.1 pitch, gold plated

square pin, male

Mounting Dimensions

Extended Configuration (card reader version)
Top mo unt requires cutout

208.60 +/- 0.5mm x 108.50 +/- 0.5mm

Underpanel mount requires cutout

214.00+/- 0.5mm x 111.00 +/- 0.5mm

Accessories [x] denotes packaging variant

Item Stock No. Notes

Mounting kit for FTMK010[x] Includes gasket and frame
Shortened Configuration

Mounting kit for FTMK010[x] Card reader version
Extended Configuration Includes gasket and frame

PC Interface 4200-00-x PS2/USB

Environmental

Water / Dust Sealed IP65 (when mounted

Operational Temperature -20

Material

Chassis Super High Impact Polymer (black)
Front Panel Stainless Steel
Keytops Chromed die-cast zinc
Keytop Legends Engraved
Contact Circuit Gold on Nickel plated FR4

Shortened Configuration (no card reader)

165.00 +/- 0.5mm x 108.50 +/- 0.5mm

Underpanel mount requires cutout

169.00+/- 0.5mm x 111.00 +/- 0.5mm

111.00

to suitable enclosure)

o

C to +60oC (Dry)

Whilst every effort is made to ensure details

are correct at time of print, specifications

are subject to change without notice.

UL File reference: E230121

Brochure designed
& produced by

NIK Design: [phone]

5000-LIT-01 Rev 2

Oct 2004

R5.0 TYP.

FM 39602

FT Integrated Keypad
with display & card reader

FT Integrated Keypad
with display only

All dimensions
are in mm

Storm Interface

364 Pennsylvania Avenue

Glen Ellyn IL 60137 USA

Tel: [phone]

Email: [e-mail]

Email: [e-mail]

Fax: [phone]

Storm Interface

14 Bentinck Court

Bentinck Road

West Drayton

Middlesex UB7 7RQ

Tel: [phone]

Fax: [phone]

www.storm-interface.com

Storm is a trademark of Keymat Technology Ltd

Storm Interface is a trading name of Keymat Technology Ltd

technology protected by international patents

Storm Interface products include

and design registration. All rights reserved.

USA Office:

Suite 202

UK Office:

STORM Integrated Keypad and Display

Application / Engineering Manual.

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 1 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Overview.

Developed for use in a new generation of financial transaction terminals, this integrated keypad, card
reader and display is suitable for use in exposed or hostile environments. The card reader and display

type can be specified, as can the number of keys and keytop legends. The keypad’s front panel can be
easily customised to compliment the colour scheme and design of the host equipment. The Storm
Integrated keypad and display can be specified with or without approved encryption electronics for
applications requiring secure financial transactions.

• Weather and vandal resistant for outdoor and unsupervised public environments.
(also available in a lighter robust construction for less aggressive environments).

• Integrated hybrid card reader-writer (optional).

• 20 Character X 4 Line, illuminated LCD display (optional). (Compatible Graphic or

Vacuum Fluorescent displays are also available).

• Rapid, responsive and reliable data entry.

• Stainless steel or polymer front plate.

• Easily and securely installed in vending machines, automated teller machines,

public telephones, ticketing machines, car-parking control equipment etc.

• Fully encrypted data comms (optional).

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not

supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 2 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 1. Options

Storm Integrated keypad and display is a versatile device that can be c on figured to suit most applicat ions . A

The
number of cosm etic and functional options can be selected to achieve the optimum environmental or operational
performance. These options can be applied to two basic chassis configurations:- The Full Size module or the

Reduced Footprint module. See Illustrations below. The options marked with a
“required to achieve a vandal resistant specification”.

The following table show s th e rang e and av ailabi lit y of opt ion al feat ure s. Check the boxes
selected options.

Option

= Required for Vandal Resistance

❑ = Optional ✔if required

 1RWDYDLODEOH

Resistance to water and dust.
(Excluding card reader mechanism
which is designed to “”drop and drain”
any water, dust or foreign objects that
enter the card reader slot).

Switch Contact Resistance

Silver Chromed metal keys. (See
section 8. Keytop details).

Moulded polymer keys with laser
engraved keytop graphics. (See
section 8. Keytop details).

Integral keytop illumination (Silver
chromed metal keytops and GFX
custom keytops only). (See section 8.
Keytop details).

GFX Keytops with a transparent snap
on cap, enabling tiles with custom
keytop characters to be encapsulated
within the keytop

Factory fitted illuminated display
module. (See section 3. Compatible
display modules).

Polycarbonate display window with
anti-reflec ti v e scr atch resistan t
surface coating.

Partial insertion smart card reader
located above the display window.

Stainless Steel closure panel for the
circuit well on the back of the module.

Availability of display window refurb
kit (See section 10 Ordering Details).

High energy impact protection plate
located behind the keypad’s switch
contact pcb (See section 9.
Dimensional Details).

Full Size Module ❑ Reduced Footprint Module ❑

Vandal

Resistant Spec

IP65

Low pressure

water jet

100 ohms

(max)

Robust Spec

IP54

Wet wipe-down,

splashes and

light rain

100 ohms

(max)

Vandal

Resistant Spec

IP65

Low pressure

water jet

100 ohms

(max)

-

❑

-

❑

❑

-

❑ ❑ ❑ ❑

-

❑

-

❑ ❑ ❑ ❑

❑

❑

❑

❑ ❑ ❑ ❑

✔ ✔ ✔ ✔

❑ ❑ ❑ ❑

❑

❑

❑

should be considered as

❑ to indicate your

Robust Spec

IP54

Wet wipe-down,

splashes and

light rain

100 ohms

(max)

-

❑

❑

❑

❑

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 3 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 2. Ratings and performance.

The following table shows the designed operational and performance data. Achieved performance may
depend on environmental or operational conditions and mode of use.

Key to symbols

= Required for Vandal Resistance

 1RWDSSOLFDEOH

Resistance to water and dust.
(Excluding card reader mechanism
which is designed to “”drop and drain”
any water, dust or foreign objects that
enter the card reader slot).

Operational Temperature
Impact Resistance

Switch Contact Resistance (keypad)

Switch Contact Bounce (keypad)
Insulation Resistance (keypad)

Breakdown Voltage (keypad)

Operating Voltage (keypad)
Operating Current (keypad)
Operational Life (keypad)

Keytop travel (keypad)

Key actuation force (keypad)

Connector (keypad)

500V AC (max

Full Size Module ❑ Reduced Footprint Module ❑

Vandal

Resistant Spec

IP65

Low pressure

water jet

Robust Spec

IP54

Wet wipe-down,

splashes and

light rain

Vandal

Resistant Spec

IP65

Low pressure

water jet

Robust Spec

IP54

Wet wipe-down,

splashes and

light rain

0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C
20 Joules via

50mm dia

steel striker

100 ohms

(max)

Light impacts

only

100 ohms

(max)

20 Joules via

50mm dia

steel striker

100 ohms

(max)

Light impacts

only

100 ohms

(max)

5ms (max) 5ms (max) 5ms (max) 5ms (max)
50 Mohms

(min)

60 secs)

50 Mohms

(min)

500V AC (max

60 secs)

50 Mohms

(min)

500V AC (max

60 secs)

50 Mohms

(min)

500V AC (max

60 secs)

24V DC (max) 24V DC (max) 24V DC (max) 24V DC (max)

50mA (max) 50mA (max) 50mA (max) 50mA (max)

4 million

cycles per key

(min)

1.4mm

nominal

160gms
nominal

0.1” pitch, gold
plated square

pin, male

connector.

2 million

cycles per key

(min)

1.4mm

nominal

160gms
nominal

0.1” pitch, gold
plated square

pin, male

connector.

4 million

cycles per key

(min)

1.4mm

nominal

160gms
nominal

0.1” pitch, gold
plated square

pin, male

connector.

2 million

cycles per key

(min)

1.4mm

nominal

160gms

nominal

0.1” pitch, gold
plated square

pin, male

connector.

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 4 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 3. Display devices.

Many types and brands of displays can be used with the
statement displays can be installed in two ways:-

1. The display module can be secured ( using thread forming M1.8 x 8mm pan head screws )
directly to female bosses moulded into the underside of the

display

assembly process. Th e female bosses on the underside of the casing ar e positioned to accept
displays with either 93.0mm x 55.0mm or 89.9mm x 48.8mm fixing hole centres, and with a
maximum depth (module thickness) of 10.0mm when measured from the mounting face.

2. Alternatively, if an auxiliary circuit board is to be installed (by the customer) into the underside of
the
directly to the auxiliary circuit board. This allows the auxiliary circuit and display to be
manufactured and tested as a sub-assembly before final assembly into the

keypad and display

LCD Displays that are dimensionally compatible with the
most leading display manufacturers including:-

POWERTIP TECHNOLOGY CORP.
Models: PG 12232-C and PC 2004-A

HYUNDAI
Model: HC 20401

VARITRONIX
Model: MGL(S)-12032B

When specifying a display for installation in the
be given to rated operational temperature ranges quoted by the chosen manufacturer,

casing. This method of installation can be achieved, at the factory, as part of the final

Storm Integrated keypad and display casing, a suitable display can be fixed and connected

.

Storm Integrated keypad and display consideration should

Storm Integrated keypad and display. As a general

Storm Integrated keypad and

Storm Integrated keypad and display are available from

Storm Integrated

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 5 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 4. Card Readers and writers.

Keymat Technology is pleased to offer the Magtek Intellistripe 65 range of full insertion card readers as a factory
supplied / fitted options. These reader / writers can be specified for installation in the full size

keypad and display

only. In addition, Keymat Technology offer the ITT Cannon and FKI partial insertion smart card
readers as an optional device (for installation above the display window) in both full size and reduced footprint
versions of the

Storm Integrated keypad and display.

Many other types and brands of card reader/writers can be incorporated in the STORM FT, however the specification
of alternative card readers may be subject to minimum order quantities or ‘Non Recurring Engineering Charges’. The
successful application and installation of alternative devices should be discussed and agreed with the STORM
Engineering Team at the earliest stage of any project.

Card readers are secured to a profiled steel bracket attached to the

Storm Integrated keypad and display terminal

by four M3 locknuts.

The table below sh ows the applicable card reader / writ er options for each

display

format.

Key to symbols

❑ = Optional ✔if required

 1RWDYDLODEOH

MAGTEK Intellistripe 65 Range of
Full Insertion Reader / Writers

AMPHENOL C 702-1 Pushmatic II
range of full insertion card readers

FKI Partial Insertion S mart Card
Reader / Writer

ITT Cannon Partial Insertion Smart
Card Reader / Writer

Full Size Module ❑ Reduced Footprint Module ❑

Vandal

Resistant Spec

Robust Spec

Resistant Spec

❑ ❑
❑ ❑
❑ ❑ ❑ ❑
❑ ❑ ❑ ❑

Storm Integrated keypad and

Vandal

- -

- -

Engineering Ref erence Data for supported card re ader / writers is includ ed (in Section 11) for ref erence purposes
only. These documents are not supported by Keymat Technology’s change note or revision control procedures.
Please refer to the device manufacturer for curr ent or additional inform ation. Keymat Technology do not warrant or
guarantee the accuracy of any ratings, data or information included in manufacturer’s reference material.

Storm Integrated

Robust Spec

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 6 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 5. Connectors and connections. (keypad and soft keys only).

The 16 key pad and the 4 adjacent soft keys (positioned beneath the display window) are configured on a 5 x 4
circuit matrix. This circuit matrix is terminated via a 13 way, 0.1” pitch, gold plated, square pin, male connector with
locking ramps

The optional keytop illumination system (when specified with the unit) is also terminated via the same connector on
pins 1 and 13.

The anti tamper facility is supplied to detect any seperation of the pcb from the unit. If this occurs then this will break
the connection (open circuit) and may be used to activate an alarm system. Connect to PIN 2 and PIN 12 to use this
facility) Rating 24 Volts dc Max

The Pinout Connection Details below shows the connector pin designation for each switch position. Switches
provide a momentary contact between designated connector pins. The Connector Details below shows the
orientation and position of the connector.

For details of connections to the display module and card reader (if fitted), please refer to the manufacturers
information in Section 11.

Pinout Connection Details

Pin 1

Connector Details

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 7 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 6. Installation in host equipment

The

Storm Integrated keypad and display can be secured into a fascia panel (or equipment casing) in two ways.

1. (Recommended for maximum tamper and va ndal resistance) . The

be installed from the underside of a pa nel, with the op erational f ace of the unit ac cessible t hrough a recta ngular
aperture in the panel. The
a retaining plate (s upplied in the Mount ing Kit – see Sec tion 10. Ordering D etails). Recomm ended dimensions

and profile for the panel ap erture and pos itions of the fixing stu ds are deta iled in Secti on 9. Dim ensional Det ails.
A sealing gasket is compressed bet ween the
rear surface of the fascia panel. This is necessary to achieve rated resistance to water and dust ingress.

2. The

It is recommended that the s ealing gasket is replaced each time the
fitted to the fascia panel or host equipment. Replacements are included in the

display

Storm Integrated keypad and display can be fixed to the outer surface of a f ascia panel (or equipment

casing). This is ac hieved by locating the unit over suitably positioned fix ing holes and aperture in the pane l, as
shown in Section 9. T he unit is th en s ec ured us i ng si x M3 s cr ews thr oug h the p ane l int o the thr e ade d ins e rts in
the case moulding. The sealing gasket is compressed between the
peripheral edge and the sur face of the fascia panel. This is necessary to achieve rated r esistance to water and
dust ingress. T o calculate the length of s crew required allow 4.5mm length of thread for housing plus sealing
gasket.

Service Kits – ( see Section 10), available from STORM Data Entry stockists.

Storm Integrated keypad and display is secured into place b y six M3 lock nuts and

Storm Integrated keypad and display sealing flange a nd the

.

Storm Integrated keypad and display can

Storm Integrated keypad and display

Storm Integrated keypad and display is r e-

Storm Integrated keypad and

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 8 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 7. Serviceability (Vandal Resistant [VR] versions only).

The

Storm Integrated keypad and display (VR) keypad is designed for use in exposed, unsupervised public

environments. It is tou gh and weather r esistant. Ho wever, de liberate att empts to vandalis e the devic e ma y leave the
steel front plate scarred, dented or deformed. The toughened, scratch resistant display window may also be
obscured by paint or aggressive abrasives. To red uce the cost of repair or replacement resulting from deliberate
vandalism some front face components have been designed to allow removal and replacement by qualified
engineers. These are listed in Section 10. Ordering Details.

Section 8. Keytop Options

Style Construction

Engraved metal (Chrome plated cast )
Polymer (Laser marked UV stable impact resistant)
Graphic (Insertable – customisable legend tiles)
Illuminated (Engraved metal or graphic styles)

Legends

The standard engraved metal legend set is shown below. Other key legends and styles are available – please refer
to library on our web site www.keymat.com.

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 9 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 9. Dimensional Details. (All dimensions in millimetres)

Reduced Footprint Module (no Reader).

Full Size Module shows Intellistripe 65 Card Reader.

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 10 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Panel Cutout (Underpanel).

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 11 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Panel Cutout (Top Mount).

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 12 of 14

Application / Engineering Manual.

Section 10. Ordering Details

Main
Units

Storm PN

FT1K 050 Vandal

FT1K 055 Vandal

FT1K 080 Vandal

FT1K 085 Vandal

FT4K 090 Robust Reduced Footprint Character None GFX
FT4K 095 Robust Full Size Character Bracket

FT4K 100 Robust Reduced Footprint None None GFX
FT4K 105 Robust Full Size None Bracket

Vandal

Resist or
Robust

Resist

Resist

Resist

Resist

Accessories

Storm PN

FTMK 0001 Mounting

FTMK 0101 Mounting

FTWK0101 Window Replacement Kit.

If the unit you require is not shown please contact your STORM Distributor or e-mail us direct at www.keymat.com

Kit .

Kit.

Full Size or
Reduced Footprint

Reduced Footprint None None Chromed

Full Size None Bracket

Reduced Footprint Character None Chromed

Full Size Character Bracket

FT Full Size.

FT Reduced Footprint.

STORM Integrated Keypad and Display

Display Reader Keytops

Metal Infill
Chromed

for INT65

for INT65

for INT65

for INT65

Metal Infill

Metal Infill
Chromed

Metal Infill

GFX

GFX

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 13 of 14

STORM Integrated Keypad and Display

Application / Engineering Manual.

Section 11. Manufacturers Data for Card Readers / Displays.

Card Readers

Refer to Magtek website: www.magtek.com

Ref No.

Description.

99875141 IntelliStripe 65 RS-232 INSERTION READER TECHNICAL REFERENCE MANUAL.
99875161 IntelliStripe 65, Command Reference Manual.
99875163 MCP, Serial Tr ansport Protocol Reference Manual.
99875164 Mag-Tek Communication Protocol, Driver Reference Manual.

Displays

Refer to Powertip we b s i t e : www.powertip.tw
Standard fitment character display is :-

20 Char x 4 Line Display PC 2004LRU-AWA-H or PC 2004LRU-ASO-H -20° C to +70 °C
Alternative normal temp range fitment is :-

20 Char x 4 Line Display PC 2004LRU-AEA-B 0 to 50 °C

Operating Voltages (V

) for each type of display are as follows :-

op

, FAQ’s are at www.powertip.com.tw/technical/Q&A.asp

LCD Type Vop for N.T. Vop for W.T.

Character 4.2 ~ 4.8V 5 ~ 9V
Graphic 5.5 ~ 26V 6 ~ 28V

Note: N.T. = normal temperature W.T.= wide temperature

What is temperature compensation and why is required?

A LCD operating voltage varies at different temperatures. The operating voltage must rise as
temperature lowers or the contrast will degrade. Conversely, the operating voltage must fall as the
temperature rises or the contrast will degrade. For this reason it is often a requirement, with graphics
modules, to control the input voltage accordingly. The temperature compensation circuit is the circuit
that controls the input voltage as the temperature changes. This temperature compensation circuit
can be located on the LCD module or on the customer’s motherboard.

This document is provided for use and guidance of engineering personnel engaged in the installation or application of STORM data entry produc ts
manufactured by Keymat Technology Ltd. Please be advised that all information, data, and illust rati ons contained within thi s document remain the
exclusive property of Keymat Technology Lt d. and are provided for the express and exclus ive use as described above. This document is not
supported by Keymat Technology’s engineering change note, revision or reissue system. Data contained within this document is subject to
periodic revision, reissue or withdrawal. Whilst every effort is made to ensure the information, data and illustrations are correct at the time of
publication, Keymat Technology Ltd. are not responsible for any errors or omissions contained within this document.

FT Application/Engineering Manual Version 1.02 Feb 2003 Page 14 of 14

Part Number Part Description

FT1K0501 STORM 5000 SERIES VR INTEGRATED KEYPAD, NO LCD
FT1K0801 STORM 5000 SERIES VR INTEGRATED KEYPAD, WITH LCD
FT2K0501 STORM 5000 SERIES VR INTEGRATED KEYPAD, NO LCD, POLYMER KEYS
FT2K0801 STORM 5000 SERIES VR INTEGRATED KEYPAD, WITH LCD, POLYMER KEYS
FT4K0901 STORM 5000 SERIES ROBUST INTEGRATED KEYPAD, WITH LCD
FT4K1001 STORM 5000 SERIES ROBUST INTEGRATED KEYPAD, NO LCD