DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 1 -
Step 1 - Set Fixed ID on the transmitter
Skip this part if you have a brand new DJI F450 RTF Package,
we have already done before we ship.
!
Make sure you have NOTHING plugged into BATT port on the RX701 receiver.
On the transmitter, goto MODEL > FIXED ID, press ENT, if it is showing the code, then
press ENT again, press one more time, it's showing RUN, press "R" to choose NO, press
ENT again, it's showing FIXID, press "R" again to choose OFF, then press EXT, and turn o
transmitter.
Plug the bind plug into Batt port on the RX701 receiver, with this plug still in BATT port
and power up the drone, you will see receiver ashing red slowly, then means old code
has been erased, unplug drone battery and remove this bind plug.
Now you need to activate the Fixed ID function.
Turn on transmitter, then make sure Throttle Stick is all the way down, all trimming is
neutral, both corner FMOD switch and Throttle Switch is o (pointing backward) and all
switches on the transmitter pointing upward, then turn o transmitter.
Connect drone battery, the receiver will start ashing, place drone on at surface.
Turn on transmitter, you should see black box running on the transmitter screen, do no
touch anything or you will break the searching mode.
Do not touch anything (around 7-10 seconds) until transmitter stop ashing and you will
see the RX701 receiver have solid light, that means binding has completed.
On the transmitter, goto MODEL > FIXED ID, turn it ON, then press DN button to conrm
the code, then press ENT, and press ENT again to conrm, it will ask you to RUN, choose
YES and press ENT. From now on your receiver is bound to this memory on your DEVO 7.
1.
2.
3.
4.
5.
6.
7.
8.
DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 2 -
Step 2 - Enter these parameters into your DEVO 7
[MODEL] > [TYPE] > AERO
[MODEL] > [INPUT] > FM SW = FMD
[MODEL] > [INPUT] > FMTRM = COMM
[MODEL] > [INPUT] > HLDSW = HOLD
[MODEL] > [OUTPUT] > GEAR = FMD and ACT
[MODEL] > [OUTPUT] > FLAP = MIX and ACT
[MODEL] > [OUTPUT] > AUX2 = AUX2 and ACT
[MODEL] > [AMPLI] > +20
[FUNCTION] > [REVSW] > GEAR = REV
[FUNCTION] > [REVSW] > FLAP = REV
[FUNCTION] > [REVSW] > AUX2 = REV
[FUNCTION] > [TRVAD] > GEAR = +0.0% / -83.5%
[FUNCTION] > [TRVAD] > FLAP = U88.0% / D88.0%
[FUNCTION] > [SUBTR] > GEAR = -5.5%
[FUNCTION] > [SUBTR] > FLAP = D5.0%
[FUNCTION] > [SAFE] > GEAR = SAFE / +40%
1.
2.
3.
4.
5.
6.
7.
8.
These are the default settings on the DEVO 7 we sent you, if you have messed up the settings,
please follow this sheet and re-enter them to the DEVO 7 transmitter.
Skip this part if you have a brand new DJI F450 RTF Package,
we have already done before we ship.
!
DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 3 -
Step 3 - How to start the DJI F450 RTF Package
Put drone in open ground, smooth and leveled surface.
Make sure no tall buildings blocking GPS signals.
Make sure throttle stick is lowest, and FMOD switch is at 0 Position, and MIX switch is also
at 0 Position.
Turn on transmitter, and connect drone battery.
Once drone is powered on, it should have ashing LED, please refer to NAZA manual
about what the LED means, that tells you the drone’s status.
Wait until drone is ashing green slowly, that means GPS signal reception is very good.
Very Important!! Wait a little longer until you see green light ashing quickly for 13
times, that means Home Point has bee recorded on the ground. If you don’t wait for
this and y, the drone will record Home Point in mid air and bad thing will happen.
Move Left stick to Lower Left, move Right stick to Lower Right to unlock Throttle.
Now rotors should be spinning.
During rotors are spinning, you can add throttle to lift o.
When drone is in mid-air, you can control the throttle stick to make it go up or down.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
!
Very Important!! If you see drone slighly tilt to one side during start up, try applying
some Elevator and Aileron stick to compensate it, because NAZA Gyro readings are
not leveled, just leave the drone on leveled ground for few minutes, NAZA Gyro will
regain level readings and drone will become more and more stable, it will not tilt to
one side and lift straight up.
However, when you start the drone it wants to tip over quickly, that means something went wrong, SHUT DOWN throttle asap and contact us for this situation.
We suspect the NAZA Gyro readings are disrupted, maybe by transportation, maybe
by electronic device, will need to connect drone to computer to check readings.
!
!
DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 4 -
Nothing happened when I unlock throttle?
Connect drone to NAZA Software, in the “Command Sticks Calibration” section, check the
R, E and A box, see any of those boxes not Green color? If yes, NAZA Gyro will think your
stick not neutral yet, try trimming the transmitter to move the box that is oset back to
central again. Once NAZA know the R, E and A box are green, it will allow you to unlock
throttle.
Q.
A.
What is ATTI mode?
ATTI mode means drone is ying with Altitude Sensor only, no GPS sensor.
If you are ying in urban area with tall buildings, we recommend you y with ATTI mode
instead of GPS mode. To switch into ATTI mode, switch the FMD switch to position 1.
Drone LED will be ashing Yellow slowly, this is ATTI mode.
Q.
A.
How to Auto Return Home?
NAZA will record home point automatically after you power on the drone for 1 minute,
you should see it ashes Green quickly, that means home point is record.
So when you are ying you want it to go home, simply turn o the transmitter, it will
enter Fail Safe mode, it will come back to the home point and land.
For more details about Fail Safe function, please read the NAZA manual.
Auto Go Home is a fail-safe feature, it meant to bring back the
drone when thing goes bad, player should not rely on this function to land the drone.
NEVER perform a Auto Return Home when low battery, because
Auto Return Home requires 100% motor output, if your battery is
low, the motors will stall during the drone decend and result a
ip-over and crash!! Always time your ight, always reserve power
for every landing.
Q.
A.
How long can Flamewheel F450 y?
With full loading (H3-2D Gimbal + GoPro 3 + FPV Transmitter + iOSD Mini), using the
11.1V 5500mah 30C battery, we have 14 minutes of ight time.
Q.
A.
!
!
DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 5 -
How to perform Compass Calibration?
On your transmitter, ip the FMD switch located on the top right corner to Position 0
(GPS Mode), then turn on transmitter, then put the drone on the table, connect the
drone battery.
After they are properly bound, ip the FMD switch to Position 1 (Atti Mode) and
switch back to Position 0 (GPS Mode), repeat this 5 times (GPS > Atti > GPS), you
should have the LED turns Solid Yellow, that means it is in Compass Calibration mode.
Now you need to do the “NAZA Dance”.
(Fig.1) Hold your Drone horizontal with tail pointing towards yourself, rotate your
body 360 degrees in 5 seconds (CW or CCW will be ne) until the LED turns solid
green, then go to the next step.
(Fig.2) Hold your Drone vertically with tail pointing towards the sky, rotate it your
body again, also 360 degrees in 5 seconds (CW or CCW will be ne) until the LED
turns o, that means compass calibration successful.
If the calibration is done, calibration mode will exit automatically. If the LED keeps
ashing quickly Red, the calibration has failed. Flip the FMD switch once to cancel the
calibration, and then re-start from Step 2.
Q.
A. 1.
2.
3.
4.
5.
DJI Flamewheel F450 RTF package
DEVO 7 Setup for NAZA V2 / Lite
- 6 -
Front
Please strictly follow the motor spinning direction and
the propellers installation.
!
Front
1
3
2
4
CW
CCW
DJI Flamewheel F450 RTF DEVO 7 Transmitter
Not used
Not used
Gimbal Tilt Control
(Using with camera gimbal)
0 : OFF/
1 : Course Lock /
2 : Home Lock
0 : GPS Mode /
1 : Manual ATTI /
2 : also Manual ATTI
Throttle Up
Stick Mode 2
Yaw Left Yaw Right
Throttle Down
Go Forward
Strafe Left Strafe Right
Go Backward
Loading...