Page 1
Stompa Midsleeper (Ladder Central)
Dimensions
Width - 208.2 cm
Depth - 98.2/105.5 cm
Height - 110.0 cm
If you need help or have damaged or missing parts, call the : 0844 8008475Customers Helpline
Important - Please read these instructions fully before starting assembly
Issue 2 - 27/11/1064762071-1
Factory code:
15620700321 - White
Assembly instructions - please keep for future reference
98.2/105.1
109.0
T1007-02 NR301-V6
Issue 1 06/10/11
T1013-02 - White
T1013-02-NOR LV371-V6
Cabin Bed
98,2 cm
72
Issue 1 15/12/11
7/8
Batch nr:
POSITION 1
POSITION 2
Use this position if adding
the Under bed Storage Unit
Page 2
Safe and Care Advice
3, 4 and 5.
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
page 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to lay out the parts before
starting.
Do not stand or put weight on
the product, this could cause damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
Dispose all packaging
carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Care and maintenance
We do not
recommend the
use of power
drills/drivers,for
inserting screws
Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
(GB) IMPORTANT, READ CAREFULLY - RETAIN FOR FUTURE REFERENCE
Current legislation requires
that the bunkbed must be fitted
with a ladder or platform for the
upper bunk bed.
The bunk bed meets the european
EN 747-1:2007 standards for security
and durability.
Mattress: Important: High beds and the upper
use a mattress size 200 cm long
and 90 cm wide. The total
thickness must not exceed 16.1 cm
The label on the ladder side indicates
maximum height of mattress to be used
in this bed.
This bed is designed to
bed of a bunk are not suitable for
children under six years due to the risk
of injury from falls.
Do not use the bed if any structural
part is broken or missing.
Be aware that children can strangle
in items such as ropes, strings, cords,
harnesses and belts attached to or
hung on a bunk bed/high bed.
WARNING
Children can become trapped
between the bed and the wall.
To avoid risk of serious injury the
distance between the
and the wall shall not exceed
barrel
75 mm or shall be more than 230 mm.
top safety
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
3/8
3
2
4
1
6
5
1
Components
4
2
3
1
ide rail x2 S
(200,6x14,5x2 cm)
2
(80,2x69,6x1,9cm)
5
(89,5x90x1,7 cm)
x2 End panel
x5 Slats
3
Leg x1
(72x90x3,8 cm)
4
Leg x1
(72x90x3,8 cm)
6
Slats
(89,5x90x1,7 cm)
x6
Page 4
30 min
Tools needed (not supplied)
4/8
A 10x40 28
B M6x75
4
C M6x10x13 4
D 7x60 4
E D35 4
F 3,5x40 8
1
1
2x
G D8x13 8
H D10x15 8
J D15x18 4
GLUE
4mm
3xA
GLUE
2x
2
4xA
1
1
1
3xA
2
D
4xA
x2810x40A
D
D
35
mm
2x
2x
43
4mm
D 7x60 x4
Page 5
5/8
3
4mm
2x
GLUE
E
4
2
E
GLUE
3
E D35 x4
4
POSITION 1
POSITION 2
4mm
B
B
B
C
C
C
B
C
C
B
1
1
B
B M6x75 x4
C
M6x10x13
x4
Page 6
6/8
5
G
J
H
G
POSITION 1
G
H
J
GG
H
J
G
2x
G
H
G
POSITION 2
J
G
J
G
H
POS. 1
G D8x13 x8 x8
POS. 2
H D10x15 x4 x8
J
6
8xF
D15x18
x4
x4
6
5
F 3,5x40 x8
Page 7
Assembly Instructions
Customer Notice
Dear Customer,
Congratulations on the recent purchase of your furniture!
Customer Service
For missing or spare parts requests please contact us Monday to Friday – 10am to 3pm in
one of the following ways:
Phone: 0844 8008475
Email: [email protected]
Please inform: product, colour, where did you buy it, part no, quantity and
reason for request. We need your full name, address and telephone number.
Fax: Please complete the enclosed Service Form and fax to 0560 1132071
By post: Please complete the enclosed Service From and post to:
Nordika Design Ltd.
High Rigg
Panorama Drive
Ilkley, LS29 9RA
We will do our utmost to supply spare parts within 7-10 working days of receipt of
request.
:
Our quality control team has ensured a high quality product that we are sure you will be
pleased with. Any components produced willfrom solid wood contain knots and
may have surface defects which are a feature of a natural product.
Page 8
Customer Service Form
Please return complete to
Name:
Address:
Contact No:
Date of purchase:
Place of purchase:
Fax: 0560 1132071
Product Name:
See assembly instructions:
Problem:
Parts Needed: Part No.
Please quote assembly
instruction or number
Quantity
Description
e.g drawer base
Loading...