STODDART W.CVS.S.10, W.CVS.S.10, WCVS.S.15, W.CVS.S.20, WCVS.S.15 Specification, Installation And Operation Manual

A guide on the use, care and maintenance

of your quality Woodson Starline product

Models:

W.CVS.S.10, WCVS.S.15, W.CVS.S.20

Snack Master Series 10, 15 & 20

SPECIFICATION, INSTALLATION

AND OPERATION MANUAL

READ ALL INSTRUCTIONS BEFORE USE

Revision Date: 27/02/2019

Page Intentionally Left Blank

Page 1

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Page 2

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Introduction

Your New Woodson Product � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Warranty Registration � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Optional � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Product Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Attention � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
General Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �4

Service

Installation

Setting Up � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5

Handling
Unpacking
Positioning
Disposal

Electrical Connection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6

Information

Specication

Technical Specifications � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7

W.CVS.S.xx

Operation

Operating Instructions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

First Time Operation
Element Settings

Cleaning � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �9

General Information
Corrosion Protection
Surface Finish
Cleaning Schedule
Materials Required
Cleaning Procedure - Conveyor and Crumb Tray
Cleaning Procedure - External Surfaces

Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11

Page 3

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Introduction

Rating Plate

Conveyor

Exit Rack

Control Panel

Height Adjustment

CAUTION

Surface is Hot

Thank you for choosing this quality Woodson product� All our products are designed and made to meet the needs of food service professionals�
By using, caring and maintaining your Woodson product according to these instructions, your Woodson product should give you many years of
reliable service�

Stoddart is a wholly Australian owned company, which manufactures and distributes Woodson commercial catering equipment�
Stoddart products are manufactured and/or engineered in Australia to provide excellent results whilst offering-value-for-money, ease-of-use
and reliability�

Stoddart manufacture and distribute a comprehensive range of equipment for kitchens, food preparation and presentation�

To register your new product go to: http://www�stoddart�com�au/warranty-registration

Confi guration may vary according to model�

Your New Woodson Product

Product Overview

Optional

Warranty Registration

Page 4

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Introduction

• Only specifi cally trained/qualifi ed Technicians (Stoddart, one of our service agents, or a similarly qualifi ed persons) should carry out any
and all repairs, maintenance and services

Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance� Keep this booklet on
hand in a safe place for future reference by other operators or users�

Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.

This appliance is not designed nor intended for household or domestic use & must not be used for this purpose.

This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:

• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety� Children should be supervised to ensure that they do not play with the product

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard

• All units MUST be installed according to the procedures stated in the installation section of this manual

• In the case of new personnel, training is to be provided before operating the equipment

• DO NOT use this unit for any other purpose than its intended use

• DO NOT store explosive substances such as aerosol cans with a fl ammable propellant in or near this unit

• Keep fi ngers out of “pinch point” areas

• Unit is not waterproof DO NOT use jet sprays, hoses or pour water over/on the exterior of the unit

• Only use this unit with voltage specifi ed on the rating label

• Do NOT remove any cover panels that may be on the unit

• DO NOT use sharp objects to activate controls

• If any fault is detected, refer to troubleshooting

• Threaded fasteners can loosen in service� Regular inspection and tightening should be carried out as required

• The manufacturer declines any liability for damages to persons and/or things due to an improper/wrong and/or unreasonable use of the
machine

When using any electrical unit, safety precautions must always be observed�

Our units have been designed for high performance� Therefore, the unit must be used exclusively for the purpose for which it has been designed�

Read these instructions carefully and retain for future reference�

The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind occurred to persons,

units or others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or maintenance, or lack of

conformity with the instructions indicated in this documentation�

Disclaimer

All units made by the manufacturer are delivered assembled, where possible, and ready to install� Any installation, removal, servicing,

maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in accordance to this

documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the

IMMEDIATE LOSS OF THE WARRANTY.

The manufacturer cannot be held responsible or liable for any unauthorized modifi cations or repairs� All modifi cations or repairs must

be approved by the manufacturer in writing before initiating� All modifi cations or repairs performed to this unit must be performed at all

times by a TRAINED AND AUTHORISED SPECIALIST.

Attention

General Information

Service

Page 5

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

• Use suitable means to move the unit: e�g�

- For smaller items use two people

- For large items a lift truck or fork pallet trucks (the forks should reach more completely beneath the unit)�

• Check the unit for damage before and after unpacking� If unit is damaged, contact the distributor and manufacturer

• Should any item have physical damage, report the details to the freight company and to the agent responsible for the dispatch within
seven (7) days of receipt� No claims will be accepted or processed after this period

• The unit is supplied fully assembled

• Remove all protective plastic fi lm, tapes, ties and packers before installing and operating

• Clean off any remaining residue from the interior/exterior of the unit using a clean cloth dampened with warm soapy water

• Choose an area that is well ventilated and provides access for future maintenance

• Place the unit on a level stable work surface capable of supporting its weight

• Do not position the unit in: wet areas, near heat and/or steam sources, near fl ammable substances

• Allow an air gap between the unit and other objects or surfaces� We recommend a minimum gap of 100mm from all sides for normal
operational use (if the unit is near any heat sensitive material we suggest you allow additional space)

• Please consult national and local standards to ensure that your unit is positioned in accordance with any existing requirement

• At the end of the appliance’s working life, make sure it is scrapped & components recycled properly

• Current environmental protection laws in the state/country of use must be observed

• Doors must be removed before disposal (if applicable)

• Power supply cable must be removed before disposal

• For further information on the recycling of this product, contact the local dealer/agent or the local body responsible for waste disposal

WARNING

Improper installation, adjustments, alterations, service or

maintenance can cause property damage, injury or death.

Installation

Setting Up

Handling

Unpacking

Positioning

Disposal

Page 6

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Installation

Aggregate electrical ratings of the unit are expressed in kilowatts in this manual�

Single Phase Units:
Supplied with an appropriately rated plug and lead fi tted and be indicated as:

• 10A plug & lead fi tted

Some procedures in this manual require the power to the equipment to be turned

off and isolated. Turn the power OFF at the power point and unplug the power

supply lead by the plug body. If the power point is not readily accessible turn the

equipment off at the isolation switch or the circuit breaker in the switchboard.

Attach a yellow “CAUTION-DO NOT OPERATE” tag. This must be performed

where relevant unless the procedures specify otherwise.

FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.

WARNING

WARNING

This unit must be installed in accordance with AS/NZS 60335.1

Notes:

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a
hazard� Please contact Stoddart for parts and we will advise how to do this in order to avoid any electrical hazard

• The power cable should be dry and/or isolated from moisture or water

Electrical Connection

Information

Page 7

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Specication

Technical Specications

W.CVS.S.xx

573

503

573

564

77

544

513

5.773

002

064

009

7.703

2.882

825

005 002

Specications

Model W.CVS.S.10 / W.CVS.S.15 / W.CVS.S.20

Height 465mm

Width 900mm

Depth 445mm

Power 2.4kW / 3.6kW / 4.8kW

AMPS 10A / 15A / 20A

Page 8

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Operation

Operating Instructions

Element Settings

Bottom Element only:
Best for single sided toasting of uneven products, such as Burger Buns�

Top and bottom Element:
Best for all types of standard breads, buns, focaccias and open snacks�

First Time Operation

1� Turn the unit on at the “Power Switch”� (The fan will start running)
2� Prepare food item
3� Set the “Top Element” and “Bottom Element” to 5
4� Set “Conveyor Speed” to 5
5� Place food item on the conveyor
6� Adjust as required: increase/decrease the “Conveyor Speed”, “Top Element” and “Bottom Element”� Repeat this process

until the desired results have been achieved

7� Once satisfied with the results, record the settings for future reference
8� Repeat this process for different foods

Top Element only:
Best for Garlic bread, herb bread, focaccias and open snacks or browning the top of the product only�

Note: Woodson Starline recommends that you time the belt speed from when the food item starts to enter the oven to when it starts to come
out� This is the time the belt takes to pass through the oven�

Page 9

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Cleaning

Operation

• Threaded fasteners can loosen in service� Regular inspection and adjustment should be carried out as required

• Cleaning is recommended for health and safety purposes and to prolong the life of the unit

• Do NOT use abrasive pads or cleaners on the stainless steel or any other metal parts of the unit

• Do NOT use industrial chemical cleaners, caustic based cleaners or bleaches and bleaching agents, many will damage the metals and
plastics used on this unit

• When drying, metal surfaces should be wiped with a soft cloth in the same direction as grained polish

• Do NOT remove any screws for cleaning� All internal sections of the unit are to be cleaned by a qualifi ed technician

• This unit is NOT waterproof, do NOT hose, do NOT pour water directly onto the unit, do NOT immerse in water

• Stainless steel exhibits good resistance to corrosion however, if not properly maintained stainless steel can rust and/or corrode

• Any sign of mild rust and/or corrosion should be thoroughly cleaned with warm soapy water and dried as soon as possible

• NEVER use abrasive pads or cleaners for cleaning

• All metal surfaces should be checked while cleaning for damage, scuffs or scrapes as these can lead to rust and further damage to the
product

• Mild rust and/or corrosion can be treated with a commercial cleaning agent that contains citric/oxalic/nitric/phosphoric acid� Do NOT
use cleaning agents with chlorides or other harsh chemicals as this can cause corrosion� After treatment, wash with warm (not hot)
soapy water and dry thoroughly

• Thoroughly wipe the surfaces dry after cleaning and do NOT let water pool on the unit� Check crevices and folds for pooling

• When using, ensure all liquids and moisture is cleaned up straight away� Food liquids such as juices from vegetables and fruits should
NOT be left on preparation surfaces

• Do NOT leave items on the stainless steel such as cutting boards, rubber mats and bottles

• To protect the polish, stainless steel should be dried by wiping a dry soft cloth in the same direction as grained polish

• For NON-food contact surfaces, a light oil can be wiped on the surfaces with a cloth to enhance the stainless steel surface� Wipe in the
direction of the grain

• Some commercial stainless steel cleaners can leave residue or fi lm on the metal; this may trap fi ne particles of food on the surface,
thus deeming the surfaces not food safe

IMPORTANT WARNING

IMPORTANT WARNING

Threaded fasteners can loosen in service.

Regular inspection and adjustment

should be carried out as required

This unit is NOT waterproof, do NOT

hose. DO NOT pour water directly onto

the unit. DO NOT immerse in water

Some commercial stainless steel

cleaners leave residue or  lm on the

metal that may entrap  ne particles of

food, deeming the surface not

FOOD SAFE.

Wait until the unit has cooled to a safe

temperature before undertaking any

cleaning or maintenance. Contact with

hot surfaces can cause burns and

serious injury.

General Information

Corrosion Protection

Surface Finish

Page 10

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Materials Required

• Stainless Cleaner

• Non Abrasive Cleaning pad

• Clean Sanitised Cloth

• Paper Towel

• Container of warm water

• Nylon Brush

• Appropriate PPE (Personal Protective Equipment)

Cleaning Procedure - Conveyor and Crumb Tray

1� Isolate from the power supply
2� Using a good quality nylon brush remove crumbs and small food items from the conveyor� (Switch the unit on to move the conveyor

forward, then switch off)

3� Wipe clean using a cloth dampened (not wet) with clean warm water until all soil has been removed� (Switch the unit on to move the

conveyor forward, then switch off)

4� Empty and clean the crumb tray� This should be done on a regular basis

Note: In some areas, particularly seaside environments, stainless steel can be subject to surface discolouration or “tea staining”�
This can be removed with an appropriate cleaning agent which contains 10% sodium citrate� Ask your supplier of cleaning chemicals for a
suitable brand�

Cleaning Procedure - External Surfaces

1� Isolate from the power supply
2� Wearing Personal Protective Equipment (PPE), apply Stainless Cleaner with the Cleaner pad to the external surfaces
3� Scrub any baked on soil with the cleaner pad in the same direction as grained polish
4� Wipe clean using a cloth dampened with clean warm water until all Stainless Cleaner and soil has been removed
5� Using a clean sanitised cloth, thoroughly wipe the stainless steel and metal parts dry� Do NOT let water pool on the unit� Check crevices

and folds

Cleaning Schedule

• Daily cleaning is required for the oven conveyor, crumb tray and external surfaces� This will help to maintain and prolong the efficiency
of your oven

• The unit should be cleaned at the end of each work day

Operation

Page 11

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Troubleshooting

Task Type - (O) = Operator

(T) = Technician Task

Problem Possible Causes Task Possible Corrective Action

Unit won’t turn on

Unit is not plugged into a

suitable power point

O Plug unit in

Power switch is in the “Off”

position

O Change the power switch to the “ON” position

Power Point is faulty T

Arrange a qualified Technician to repair the power

point

Conveyor not turning on Conveyor Motor faulty T Lubricate / replace conveyor motor

Conveyor speed dial not

responding

T

Replace speed dial / Computer board

(whichever is applicable)

Bearings Worn T Replace Gear Head

Conveyor chain binds up in

operation

Sprocket worn T Replace sprocket

Belt loose T Remove a chain link

Unit is overheating Airflow blockage O

Clear dirt / dust from fan guard and/ or clear all air

vents around the unit of any obstructions

Fan not working T Replace fan

Unit is not heating Elements not working T Replace Elements as required

Temp switch / Computer board

not working

T

Replace switch / Computer board

(whichever is applicable)

Product is burning Conveyor too slow O Adjust speed settings as required

Temperature set too high O Adjust temperature settings as required

Product is undercooked Conveyor is too fast O Adjust speed settings as required

Temperature is set too low O Adjust temperature settings as required

Operation

WARNING

Technician tasks are only to be completed by qualied service

people. Check faults before calling service technician.

• If any faults/issues occur with the unit, follow the below troubleshooting procedures

• If the troubleshooting procedures do not correct the problem, contact the Stoddart Service Department

Page Intentionally Left Blank

Page 12

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Page 13

Due to continuous product research and development,

the information contained herein is subject to change without notice.

www.stoddart.com.au

www.stoddart.co.nz

Page 14

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

www.stoddart.com.au

International

Sales

Tel: [phone]

Email: [e-mail]

Service / Spare Parts

Tel: [phone]

Email: [e-mail]

Email: [e-mail]

www.stoddart.co.nz

New Zealand Business Number: 6837694

New Zealand

Sales

Tel: [phone]

Email: [e-mail]

Service / Spare Parts

Tel: [phone]

Email: [e-mail]

Email: [e-mail]

www.stoddart.com.au

Australian Business Number: 16009690251

Australia

Sales

Tel: [phone]

Email: [e-mail]

Service / Spare Parts

Tel: [phone]

Email: [e-mail]

Email: [e-mail]