This electric R/C model plane is not a toy.
Assemble the plane according to the instructuons,Do not
alter or modify the model,If you make any modifications,
you will void your warranty.
Children under 12 years old must use it accompanied by
an aduit.
Test the operation of the model before before each flight
to insurethat all equipment is operating properly,and that
the model remainsstructurally sound.
Fly only on calm days(with wind speeds less than 6 mph)
and in large open areas free of trees,people,building or
any other obsracles.
REMEMBER:Take your time and follow the instructions to
end up with a well-built model that is durable and easy to fly.
ELECTRIC R/C MODEL PLANE
PRODUCT MANUAL
Aileron：Controls roll（right/left） ；
Elevator：Controls pitch（up/ down） ；
Rudder：Controls yaw（right/left direction）；
Receiver ( RX)：provides input to the control surfaces and ESC ；
Power system- ESC( Electronic Speed control)：Controls the speed of motor；
Motor：Rotate the propeller to provide thrust；
Li-Po battery ：Rechargeable batteries which are used to power the airplane . Li-Po batteries
are lighter and smaller than the most other types of rechargeable batteries；
Transmitter ( TX) ：The hand-held unit that sends signal to the receiver. Moving the sticks
control direction, climb/descent, roll and motor speed；
Neck S tra p
atta chm ent poi nt
Motor ESC
Antenna
Receiver
Aileron Servos
Rudder Servo
Elevator Servo
Li-Po Battery
LED
Length：880mm
Wing span：1800mm
Wing area：23dm
Flying weight：685g
Wing load：29.7g/ dm
Power system：Brushless motor ,1000mAh 11.1V Li- Po battery
Propeller：10×6 Folding propeller
Radio required：4CH transmitter & receiver,4 micro servos
SPECIFICATIONS
GLOSSARY
2
2
CONTENTS OF KIT
01、Fuselage ×
02、 Hatch ................................×1
03、Left Wing ...........................×1
04、Right Wing .........................×1
05、Stabilizer ...........................×1
06、Screw ................................×1
07、Carbon Rod .......................×1
08、Transmitter ........................×1
09、Battery pack.......................×1
10、Decals ...............................×1
11、Product Manual ..................×1
........................... 1
1
2
3
4
5
7
8
6
9
PREPARE THE TRANSMITTER
1、Locate the transmitter ；
2、The transmitter requires eight alkaline “AA” batteries. To install the batteries, remove
the battery hatch by sliding it down and inserting them into place . Be sure to
follow the polarity diagram inside the battery compartment. Reinstall the battery hatch
.
CAUTION: (1)、Don' t use rechargeable batteries
(NiCd&NiMh);
(2)、Don' t mix old and new batteries;
(3)、Don' t mix alkaline and standard (carbon-zinc)
batteries;
3、Switch the transmitter on and check the LED on the front of
the transmitter . If the green LED is on it is safe
to fly. If the red LED is flashing, install fresh batteries. Also
check to make sure that the batteries are installed correctly.
4、Switch the transmitter off and stand by for later use.
(PIC.01)
(PIC.02)
(PIC.03)
(PIC.04)
CHARGE THE BATTERY
FOX is equipped with a 2cell-7.4V Li-Po battery pack
. The Li-Po battery has two connectors. One is for
cell balance charging and the other is for discharging.
CAUTION：1、Only charge the Li-Po battery with Li-Po battery
balance charger. Or use a conforming charger
which can ensure the Li-Po battery safety
during charging.
(PIC.05)
Balance chargi ng conn ector
Discharging
connector
(PIC.01)
(PIC.04)
(PIC.02) (PIC.03)
(PIC.05)
(2)、Before charging, disconnect the battery with any power. After each flight ,
removethe pack from the airplane and allow it to cool completely before
recharging.
(3)、During the charging process, keep the charger or battery pack in a normal
temperature area and away from source of ignition. Do not cover the charger
or battery pack with carpet, clothe or anything else. Air circulation is necessary
for proper cooling.
(4)、Important: Never leave a charging battery unattended. Please stop
charging immediately of the battery temperature rise rapidly.
Please choose the proper power, battery and transmitter or it will reduce the
longevity under the incorrect improvements.
Tool will be required for assembly as below
ASSEMBLE THE AIRPLANE
Nipper pliers Screw driver Spanner
5.5mm
INSTALL THE FUSELAGE
1、Parts for installation:
(1)、Fuselage ;
(2)、Horizontal Stabilizer
;
(3)、Screw ;
(4)、Left Wing & Right
Wing ;
(5)、Carbon Rod ;
(PIC.06)
(PIC.07)
(PIC.08)
(PIC.09)
(PIC.10)
2
3、Install the horizontal stabilizer onto the holder on fin as
picture shows ;
4、Fix the horizontal stabilizer with the screw to avoid
loosening ;
5、Insert the carbon rod through one of the wings ,
and then put the other end of carbon rod through the
fuselage and the other wing .
、Install the “Z”end of push rod to the horn of elevator ;(PIC.11)
(PIC.12,PIC.13)
(PIC.14)
(PIC.15)
(PIC.16)
(PIC.06) (PIC.07)
(PIC.08)
(PIC.09) (PIC.10)
(PIC.11)
6、Before fix the wings and fuselage in place , open the canopy hatch and
push the two aileron servo wires through the fuselage
into the canopy as picture shows . Take the
aileron servo wires and connect to the servo extension
leads . Ensure the polarity should be contacted
correctly .
7、Fit the wings and the fuselage in place . Then
tighten the screws under the wings , to avoid
the wings loosening .
(PIC.17)
(PIC.18)
(PIC.19)
(PIC.20)
(PIC.21)
(PIC.22)
(PIC.23)
(PIC.12) (PIC.13) (PIC.14)
(PIC.15) (PIC.16) (PIC.17)
(PIC.18)
(PIC.21)(PIC.19) (PIC.20)
(PIC.24)(PIC.22) (PIC.23)
INSTALL THE BATTERY
TEST THE RADIO CONTROL SYSTEM
1、Make sure the transmitter is switched on. Adjust all the trim levers to their neutral positions;
2、According to the following instructions, set up the power system(ESC) propeller function,
meanwhile the ESC brake function is optional to customers.
Note: The FOX RTF version includes a power system (ESC) with a brake function,
which can be programmed to make the propeller stop rotating then folding, reducing wind
resistance during glide when the throttle is cut off for landing.
We recommend that the brake function should be on for the FOX.
(1)、 ①Ensure that the throttle control stick is fully backward (to its lowest position);
NOTE: If the battery is connected to the plane at this time, disconnect it for
seconds;
②Connect the battery to the plane' s electronics. The power system ( ESC) will
immediately respond and remind the user if the propeller brake is “off”
(single beep) or “on”(two beeps) .
③If there is one single, it shows that the brake is in the off position. Then the propeller
will still turn under power off. This causes drag and reduces the plane' s ability to
maintain glide speed during landings.
5
1、Locate the battery. Ensure the battery has been charged and has enough power before
next step.
2、Turn the transmitter on . Attach the battery connector to the power plug of the
fuselage . The ESC will respond with one or two beeps. Place the battery in
place as shown in the picture .
(PIC.25)
(PIC.26)
(PIC.27)
WARNING:The ESC is now armed and the propeller will turn if the throttle stick on the
transmitter is moved, possibly resulting in damage or injury.
NOTICE:(1)、Before ecting the battery, make sure the LED on the transmitter is on.
(2)、Fit the battery in its place as shown. Otherwise, the CG position will
be changed due to the movement of the battery. The plane will lose
its balance potentially.
3、Test fit the canopy hatch into the fuselage as picture show . It is important
to make sure the battery hatch attached tightly to avoid falling off during the flight
.
(PIC.28)
(PIC.29,PIC.30)
(PIC.25) (PIC.26) (PIC.27)
(PIC.28) (PIC.29) (PIC.30)
Do it as the step (2) below if you want to get the brake on.
④If there are two beeps, the propeller brake is on and the propeller will come to a
stop quickly when the throttle stick is in the off or down position, reducing drag.
Do it as the step (3) below if you switch to brake off.
(2)、 Switch from without brake mode to with brake mode: Disconnect the battery with the
airplane before operation switch
①Move the throttle control stick forward (at the top) .
②Plug the battery to the fuselage.
③Wait for 5 seconds, there are two beeps.
④Move the throttle control stick backward (to its lowest place) .
(3)、 Switch from the brake mode to the mode without brake Disconnect the battery with the
airplane before operation switch.
①Move the throttle control stick forward (at the top).
②Plug the battery to the fuselage.
③Wait for 5 seconds, there is a beep.；
④Move the throttle control stick backward (to its lowest place).
3、Test the power system:
(1)、 The transmitter power should be on now and the
throttle at minimum position . Pls make sure that
the ESC brake function is either “ on “ or “ off” and
the prop should be held still , if the prop
is turning slowly , then ensure that the throttle
control stick is at minimum position , if not, then
trimmed to the throttle at minimum .
(PIC.31)
(2)、 Move the throttle control stick forward slowly;
if the motor rotates faster gradually .
If the motor doesn't react with the throttleincreasing,
please check the power supply or the battery capacity.
WARNING: Keep everything clear of the propeller once the
battery is plugged in. Do not try to stop the propeller by
hand or anything else.
(PIC.32)
NOTE:
4
(1)、 Move the aileron control stick to the left, the left aileron moves up and the right
one moves down .
(2)、 Move the aileron control stick to the right, the right aileron moves up and the
left one moves down .
(3)、 Moves the stick to its neutral position, the aileron returns its neutral position
.
、Test the aileron:
(PIC.33)
(PIC.34)
(PIC.35)
(PIC.31)
(PIC.32)
(PIC.33) (PIC.34) (PIC.35)
NOTE: If the movement of aileron works in opposite position, please check the
aileron reverse switch on the transmitter and make necessary alignment.
5
(1)、 Move the rudder control stick to the left, the rudder turns to the left .
(2)、 Move the rudder control stick to the right, the rudder turns to the right
.
(3)、 Move the rudder control stick to its neutral position, the rudder returns its
neutral position .
NOTE: If the movement of rudder works in opposite position, please check the rudder
reverse switch on the transmitter and make necessary alignment.
、Test the rudder:
(PIC.36)
(PIC.37)
(PIC.38)
6
(1)、Move the elevator control stick backward, the elevator will be up .
(2)、Move the stick forward, the elevator will be down .
(3)、Move the stick to its neutral position, the elevator returns its neutral position
.
NOTE: If the movement of elevator works in opposite position, please check the
elevator reverse switch on the transmitter and make necessary alignment.
、Test the elevator:
(PIC.39)
(PIC.40)
(PIC.41)
WARMNING: Please check if the aileron, rudder, elevator can be neutral position while the
stick & trim is at the neutral. If not, then, untie each adjuster screw of the servo
horns, adjust the length of the pushrod, and then tighten the screws to avoid the
pushrod loose .
If loose of the pushrod,
then lead the airplane to
unstable, and result in
crash.
(PIC.42,PIC.43)
(PIC.36)
(PIC.41)
(PIC.37) (PIC.38)
(PIC.39) (PIC.40)
(PIC.43)(PIC.42)
CG(Center of Gravity)POSITION
PRECAUTIONS BEFORE FLIGHT
(PIC.44)
(PIC.46)
7
(1)、Aileron (2)、Rudder (3)、Elevator
、Movement of all control surfaces:
1、The standard CG is positioned ahead the line as picture shows ;
2、Move the CG forward, the
flying performance is stable;
move backward, the flying
performance is sensitive.
NOTE: The movement of the
CG should not exceed
±2mm;
3、We recommend only use the battery pack intended for FOX, or use the same weight
and performance battery packs. If the battery pack or other accessories have changes,
please adjust the CG position according to the content above.
(PIC.44,PIC.45)
1、The FOX should be flown only when the wind speed is 6 mph or less. If the wind is
calm or very light, the FOX will be docile and easy to control. If you have few flight, fly
only when the wind speed is 1 mph or less. After you have enough flight, you can fly
in winds that are no more than 6 mph per hour. If flown in stronger winds, the
plane may be blown down wind and not have enough power to get back. The
visibility range should not less than 1000m. Do not fly in rain or fog. Please check the
direction of wind before your flying.
2、Also, Choose a large open area free of trees, power lines ,railway, road, parking lot,
buildings or any other obstacles. Do not fly around groups of people, especially children.
We recommend that the lawn or links are good flying field.
4、Make sure no one use the same radio frequency as you
do in the same area to avoid frequency interference.
There is a frequency label on the transmitter crystal,
which shows the frequency band you use ;
if someone in your area use the same frequency, do
not switch on the transmitter until their flight finished.
(PIC.46)
3、Don't fly in aviation control areas or military bases.
5、
power for the plane to avoid interference; make sure
the battery is charged and fresh AA batteries are
installed in the transmitter.
Always switch on the transmitter before supplying
(PIC.45)
6mm±2 mm
20
o
20
o
15
o
15
o
15
o
15
o
If you have never flown an R/C airplane before, we recommend that you get help
from an experienced R/C pilot. Most R/ C clubs have training programs that will help
you learn to fly quickly. If you cannot find an experienced pilot to help you learn, the
following will help you get your airplane into the air.
1、First switch your transmitter power switch “ON”. Ensure the power control stick is at
the lowest position and the trim lever ie at the neutral position.
2、Connect the battery with the plane. The propeller will rotate fast if you pull the power
control stick to a higher position.
CAUTION: Stay clear of the propeller. Always keep your hands behind the propeller.
3、Make a range check before each flight. Have an assistant hold the plane. With the
antenna folded, walk 100 feet (about 30m) away from the plane and then hold the
transmitter with the antenna pointing up to test the responses of each control surface
by moving the control sticks. Also, turn the motor on and check the range. If you still
have control of the airplane, it is safe to extend the transmitter antenna and fly the
plane; if not, check if there are fresh batteries installed in the transmitter and if the
battery in the plane is charged; also make sure the wire antenna is extending out the
back of plane.
4、Please Check the direction of wind. The plane should take-off against the wind. With the
throttle stick moved fully to the top, the propeller rotates fast. Then hand launch the
plane into the wind, at a slight upward angle (0-10 degrees) . Pull the stick toward you
so that the plane climbs at a 10 to 30 degree angle. Allow the airplane to climb a
few seconds before turning it.
5、
combined with a small amount of up elevator, your plane will turn left; move the aileron
control stick to the right, your plane will turn right. To stop the turn, move the stick the
opposite direction until the plane is flying level and return the elevator to center.
CAUTION: Only a smallamount of up elevator is needed here.
6、When the plane is coming toward you, move the aileron control stick to the left. But the
plane flies to your right. That is to say, you have to reverse the way to control ailerons
when the plane flies toward you. Here's a good way for you, you can turn your body
when the plane flies toward you so that you are facing the same direction the plane is
flying to; you can look at the plane over your shoulder. Now when you move the aileron
control stick to left the plane will fly to your left.
When the plane is moving away from you, move the aileron control stick to the left,
FLIGHT
The FOX RTF version includes the “Auto Cut-Off” feature of the speed control
provides an extra degree of insurance when the battery runs low. It reacts to low power
by decelerating the rotate speed of motor even cut the power supply to the motor, in effect
saving power for the receiver. That way your airplane goes into a glide and you stay in
control as you land.
The FOX is for pilots who graduate to a more complex airplane. Have an experienced
pilots instructed how to test and fly for pilots without any experience.
6、
7、When the plane climbs to a high enough altitude, you can adjust the trim lever to
maintain straight and level flight. When loose the elevator control stick, if the plane
tends to nose up, you can push the elevator trim lever to the direction away from you;
if the plane tends to nose down, you can push the elevator trim lever to the direction
towards you. Only a small amount of adjustment should be OK. If the plane doesn't go
as you adjusted, you can adjust twice or more. Your goal is to get the plane fly level or
climb at a very small angle (like 0-5 degrees) with the elevator, throttle control stick at
their neutral positions.
LANDING
It's time to land the plane now. The problems you are facing are where and how to land it.
1、For the sake of safety, you should land the plane before the battery exhausted if you
are a beginner. The power system of FOX comes with “Auto Cut Off” feature
which reserves battery power for safe landing.
2、During the first flight, while at a high altitude, turn the motor off and retract the flaps
(move it at position “1” or “2”), Then notice how the plane reacts. This will give you an
idea of how the plane will react during a landing.
10、With the plane flying level, check to see if the plane is flying straight. Move the aileron
control stick in neutral position, if the plane wants to turn, move the aileron control trim
lever opposite the direction the plane is turning. Then the plane is trimmed OK. If you
take your hands off the sticks, the plane will fly straight and level on its own. Having the
plane trimmed properly makes flying much easier and more enjoyable.
11、Don't let the plane get too far away from you. The farther away it is, the harder it is to
see what the airplane is doing. Especially when the battery runs low, you should control
the plane back to you immediately.
3、To land the FOX, fly down wind, past the landing area. Gently turn into the wind and
reduce the speed so that the plane starts to come down. Adjust the throttle when needed
to reach the landing area, but not fly past it. Get the plane 1m or 2m above the ground
when it is closed to the landing area.
4、Just before landing, at about 0.5m above the ground, apply a little up elevator to make
the plane nose up (not to make it climb). This will cause the plane to slow and settle to
the ground. Please don't force it to stop by your body or anything else.
COUTION: Just before the plane touching down, pull the throttle control stick to its lowest
position. Because after landing, the propeller cannot rotate with the throttle in
the run position. Immediately move the throttle stick down to stop the motor. If
you fail to do this, the propeller will be damaged because of hard landing.
And the motor, speed control or the battery will become very hot and be
dangerous.
AFTER THE FLIGHT
Unplug the battery with the plane and switch off the transmitter. Allow enough time for
the motor and battery to cool before recharging. Check the plane carefully and make sure
no parts have gotten loose or damaged.
9、For beginners, rudder is mainly used for take off and landing. During take off and
landing, it is necessary to control the plane turn to left or right by controlling the rudder,
instead of controlling the aileron. Move the rudder control stick to the left will make the
plane turn to left; move this stick to the right will make the plane turn to right. If the plane
tends to turn with the left stick centered, move the rudder trim lever opposite the
12、When learning to fly, it is best to keep the plane high enough so that you have enough
altitude to correct it if you make a mistake.
Loading...