ST MICROELECTRONICS STLINK-V3MINIE Datasheet

Page 1
STLINK-V3MINIE
Data brief
STLINK-V3MINIE debugger/programmer tiny probe for STM32 microcontrollers

Features

Tiny 15 mm × 42 mm standalone debugging and programming probe for STM32 microcontrollers
Selfpowered through a USB Type-C® connector
Probe firmware update through USB
Optional draganddrop Flash memory programming of binary files
Communication bi-color LED
JTAG communication support up to 21 MHz
STLINK-V3MINIE top, bottom, and cable views. Picture is not contractual.
SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 24 MHz
Virtual COM port (VCP) up to 15 Mbps
1.65 to 3.60 V application voltage support
Board connectors:
USB Type-C® connector
1.27 mm pitch STDC14 debug connector with STDC14 to STDC14 flat
cable
2.0 mm pitch on-board pads for BTB (Board-to-board) card edge connector
Product status link
STLINK-V3MINIE

Description

STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for
STM32 microcontrollers.
The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.
STLINK-V3MINIE also provides a Virtual COM port interface for the host PC to communicate with the target microcontroller through one UART.
STLINK-V3MINIE is a portable version easytouse debugger and programmer including STDC14 interface with its flat cable and onboard pads for boardtoboard (BTB) card edge connector.
DB4541 - Rev 2 - December 2021 For further information contact your local STMicroelectronics sales office.
www.st.com
Page 2

1 Ordering information

To order the STLINK-V3MINIE tiny probe, refer to Table 1. For a detailed description of the board, refer to its user manual on the product web page.
Order code Content and references User manual Description
STLINK-V3MINIE
1. Tiny probe board.
2. Flexible flat cable.
MB1762
FFC

1.1 Product marking

The stickers located on the top or bottom side of the PCB provide product information:
Product order code and product identification for the first sticker
Board reference with revision, and serial number for the second sticker
On the first sticker, the first line provides the product order code, and the second line the product identification.
On the second sticker, the first line has the following format: “MBxxxx-Variant-yzz”, where “MBxxxx” is the board reference, “Variant” (optional) identifies the mounting variant when several exist, "y" is the PCB revision and "zz" is the assembly revision, for example B01. The second line shows the board serial number used for traceability.
Evaluation tools marked as “ES” or “E” are not yet qualified and therefore not ready to be used as reference design or in production. Any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering sample tools as reference designs or in production.
“E” or “ES” marking examples of location:
On the targeted STM32 that is soldered on the board (For an illustration of STM32 marking, refer to the STM32 datasheet “Package information” paragraph at the www.st.com website).
Next to the evaluation tool ordering part number that is stuck or silk-screen printed on the board.
(1)
(2)
Table 1. Ordering information
STLINK-V3 in-circuit debugger and
UM2910
STM32 board featuring a doublerow, 14pin
STLINK-V3MINIE
Ordering information
programmer for STM32 microcontrollers with level shifter
(2 × 7) female ZIF connector
DB4541 - Rev 2
page 2/5
Page 3
STLINK-V3MINIE
Development environment

2 Development environment

STLINK-V3MINIE runs with an STM32 32bit microcontroller based on the Arm® Cortex®-M core.
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

2.1 System requirements

®
Note:
MultiOS support: Windows® 10, Linux® 64-bit, or macOS
USB Type-A or USB Type-C® to USB Type-C® cable
macOS® is a trademark of Apple Inc. registered in the U.S. and other countries.
Linux® is a registered trademark of Linus Torvalds.
All other trademarks are the property of their respective owners.
2.2

Development toolchains

IAR Systems® - IAR Embedded Workbench
Keil® - MDK-ARM
STMicroelectronics - STM32CubeIDE
1.
On Windows® only.
(1)
®(1)
DB4541 - Rev 2
page 3/5
Page 4

Revision history

STLINK-V3MINIE
Table 2. Document revision history
Date Revision Changes
30-Sep-2021 1 Initial release.
1-Dec-2021 2 Updated Cover image, Features, and Ordering information.
DB4541 - Rev 2
page 4/5
Page 5
STLINK-V3MINIE
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2021 STMicroelectronics – All rights reserved
DB4541 - Rev 2
page 5/5
Loading...