STM SatLink 4033 User Manual
SatLink 4033
Ku-Band Transceiver
Integrates the BUC, LNB and OMT sections into one
compact and lightweight casing. When combined
with the standard DiSEqC™ power control feature on
the transmitter, installation time is greatly reduced.
● Compact and Integrated Design
Features & Benefits
The built in power detector communicates with the
ODU, transmitting power usage data, the ODU serial
number, and other information to the IDU, greatly improving the ease of installation and logistics.
● Simplified Installation
During production, the P1dB compression point is
measured across the full 500 MHz transmit range and
the calibration data is stored inside the unit. When
powering up the transceiver, the SatLink IDU will
download the calibration table and enter into a continuous monitoring loop, preventing the transceiver
from ever transmitting beyond its P1dB compression
point. To the network and satellite operators, this
means less interference to neighboring sites and improved link margins.
● Embedded Transmit Power Control
Fits directly onto a C120 interface with 6 UNC screws,
with holes evenly spaced at 60 degrees, giving great
versatility in customized implementations.
● Compatibility
Integrated design virtually eliminates the possibility of
mistakes during the LNB/OMT/BUC/Feed assembly
stage.
● Accuracy
The SatLink 4033 is the first DVB-RCS certified outdoor unit to fully integrate a Ku-band transmitter
and receiver into a single compact, lightweight
casing. The 2 Watt transceiver is compatible with
most VSAT antennas. When combined with the
standard DiSEqCTM power control feature on the
transmitter, the result is a significant reduction in
installation time.
The SatLink 4033 is a member of a family of SatLink
products and systems from STM enabling scalable, high-availability DVB-RCS networks optimized for Internet Protocol (IP) communications, including: VSATs, turnkey hub and gateway
systems, hub components, and value-added options for advanced data, voice and video
networking via satellite. STM is the technology and market leader in DVB-RCS satellite networks delivering superior performance for telecom service providers, ISPs, governments and
enterprises around the world. STM also offers integration, installation,
24 x 7 global support, and managed network services.
SatLink 4033
Ku-Band Transceiver
Specifications
Frequency: 14.0 - 14.5 GHz
P1dB Compression: 33 dBm
RF Interface
IF Interface
Local Oscillator
Frequency: 950 - 1450 MHz
Connector: F-type, 75 Ohms
DC Supply: 18-28 VDC
Power Consumption: < 20 Watt
Control Channel
Extended DiSEqC v. 4.2
22 kHz two-way signaling downstream channel
RF Interface
Frequency: 10.7 - 12.75 GHz
Noise Figure at OMT: 1.0 dB typical
Conversion Gain: 58 - 68 dB
IF Interface
Frequency: 950 - 2150 MHz
Connector: F-type, 75 Ohms
Output Level, P1dB: +5 dBm
DC Supply: 13 - 18 VDC
Current Drain: 120 mA Maximum
Band Selection (Lo/Hi): 22 kHz Tone (Off/On)
Physical/Environmental
Temperature: -35°C to +55°C (operating); -35°C to
+80°C (storage)
Humidity: 0 to 100 % condensing (operating); 0 to 100
% non-condensing (storage)
IP Grade: IP 64
Size: 21.1 x 14.1 x 4.4 cm
Weight: 1.2 kg
www.stmi.com
STM Group, Inc. | 2 Faraday | Irvine, CA 92618, USA | T +1 949 273 6800 | FAX +1 949 273 6020
STM Norway AS | Vollsveien 21 | 1366 Lysaker, Norway | T +47 6753 5337 | FAX +47 6753 5335
All specifications and features subject to change without notice. SatLink and the STM logo are a registered trademarks of STM Group, Inc.
The DVB logo is a registered trademark of the DVB Project (www.DVB.org). DiSEqC is a trademark of Eutelsat.
Document #105536; Revision J - 110830 © 2011
Local Oscillator
Frequency: 9.75 GHz (Lo band); 10.6 GHz (Hi band)
SSB Phase Noise: 10 kHz : -85 dBc/Hz; 100 kHz : -105
dBc/Hz; 1 MHz : -120 dBc/Hz
L.O. Stability: +/- 1 MHz
Gain & Spurious
Linear Gain: 57 dB typical
Gain Ripple - 500 MHz: 4 dB typical
Gain Ripple - 50 MHz: 1.5 dB typical
Temperature Stability: 3 dB
Spurious in Tx Band: -50 dBc
Transmitter Receiver
Frequency: 13.05 GHz, locked to ext. ref.
Reference Frequency: 10 MHz (fed via Tx connector)
Reference Level : -5 to +5 dBm
SSB Phase Noise: 1 kHz : -70 dBc/Hz; 10 kHz : -80 dBc/
Hz; 100 kHz : -93 dBc/Hz; 1 MHz : -117 dBc/Hz
Antenna Interface
Polarization: Linear / Linear, Cross-polar
Feed-horn Interface: C120
Tx/Rx Cross-polar Level: 35 dB / 35 dB
Compliance
Regulatory: CE (R&TTE), Anatel
Loading...