Page 1
INSTALLATION GUIDE
8" FLOATING MULTIMEDIA DISPLAY SYSTEM
MODEL NUMBER: UN1880
Copyright © 2018
StingerElectronics.com
Page 2
PRECAUTIONS
Installation of this product requires technical skill
and experience. It is recommended to have it
professionally installed by a Stinger / Phoenix
Gold Dealer.
Read entire instructions thoroughly before
starting.
Disconnect the vehicle's negative battery cable
before making any wire connections.
Protect all vehicle surfaces with tape or plastic
Do not install components in any location that
will hinder vehicle operation, such as steering
wheel, gearshift, air bags, hazard switch.
All wiring should be secured away from sharp
edges and moving parts.
AGREEMENT: End user agrees to use this product
in compliance with the instructions and terms of
use and with all State and Federal laws. STINGER
provides instructions and safety warnings with
respect to this product and disclaims all liability for
any use not in conjunction with those instructions
or other misuse of its product. If you do not agree,
please discontinue use and contact STINGER. This
product is intended for off-road use and passenger
use only.
Visit StingerElectronics.com for updates and further detailed information.
Page 3
MODEL NUMBER: UN1880
INSTALLATION GUIDE
CONTENTS
Precautions...........................................2
Parts List...............................................4
Assembly & Mounting...........................5
Wiring & Connections...........................8
TECHNICAL SUPPORT:
800-477-2267
support@aampglobal.com
CUSTOMER SOLUTIONS:
800-477-2267
customersolutions@aampglobal.com
Stinger is a Power Brand of AAMP Global
15500 Lightwave Drive, Suite 202
Clearwater, Florida 33760
Page 4
PARTS LIST
QTY
1
1 Radio Module UN1880-M
Touch Panel Display UN1880-D
DESCRIPTION PART NO
Mounting Brackets / Hardware
1 Plastic Dash Mounting Bracket
1 Display Mounting Clamp
SE-1000
1 Metal Mounting Bracket
1 Horizontal Display Angle Plate
1 Rubber Boot SE-1001
4 M4 X 6 Screw
4 M4 X 14 Screw
2 M4 x 18 Screw SE-1002
6 M5 x 10 Screw
4 #10 x 3/8 Screw
2 Backstrap SE-1003
Cables / Harnesses
1 8 Pin Display Power Harness SE-1100
1 LVDS Display Video Cable SE-1101
1 16 Pin Power / Speaker Harness SE-1102
1 24 Pin AV / Rear Camera Harness SE-1103
1 10 Pin Multi Camera Harness SE-1104
1 6 Pin SWI / IR Harness SE-1105
1 4 Pin Mic / Camera Audio Harness SE-1106
1 SiriusXM Cable SE-1107
1 External Microphone SE-1108
1 GPS Antenna & Mounting Plate SE-1109
OPTIONAL ACCESSORIES
DESCRIPTION PART NO
IR Remote Control SE-1500
(SOLD SEPARATELY)
8 Pin Display Power Harness - 5FT SE-1501
LVDS Display Video Harness - 5FT SE-1502
PAC Dash Mount HDMI & USB Extension - 3FT HDMI-USB-CBL
PAC Dash Mount USB Adaptor - 3FT/6FT USDMA3 / USBDMA6
iGO North American Map (Micro SD Card) SE-P14
4
Page 5
MULTIPLE MOUNTING OPTIONS...
ELEV8 can be configured for different mounting applications:
• Using a Double DIN Dash Kit
• Using Factory Radio Mounting Brackets
• Using a Single DIN Dash Kit
• Custom Mounting Applications
This installation guide will cover using a Double DIN Dash Kit
ASSEMBLY AND MOUNTING
Using Double DIN Dash Kit
Attach metal bracket (1) to the plastic
1
dash mounting bracket (2) using M4 X 6
screws. Attach metal bracket and plastic
dash mounting bracket assembly to the
radio module (3) using M4 X 6 screws.
1
M4 X 6
3
2
The display can be installed FLAT or ANGLED
towards the driver. For flat mounting, attach the
clamp assembly (6) to the display using M4 X 14
screws (FIG. A). If a horizontal angle is desired,
insert the angle plate (7) in between the clamp and
display and replace 2 of the M4 X 14 screws with
M4 X 18 screws on the thicker side of the angle
plate (FIG. B). Center the bracket on the back of the
display as a starting point, and if needed you can
adjust up or down.
FIG. A
TOP
M4 X 14
(4X)
M4 X 6
FIG. B
2
M4 X 14
(2X)
6
M4 X 18
7
(2X)
5
Page 6
ASSEMBLY AND MOUNTING
Using Double DIN Dash Kit
Display Adjustment:
3
Loosely attach the radio module and
mounting bracket assembly to the
side brackets of an aftermarket dash
mounting kit using #10 X 3/8 screws
for the bottom locations and the M5 X
10 screws for the top locations (radio
chassis), do not tighten (FIG. A).
Temporarily attach the display to the
bracket assembly (FIG. B).
Using the main frame of the dash kit as
a guide, slide radio assembly forward
or backward to desired position. Tilt
the display vertically and determine if
the display should be flat or tilted up. If
display needs to move up or down,
refer to Step 2.
AFTERMARKET
DASH KIT
(NOT INCLUDED)
FIG. A
M5 X 10
#10 X 3/8
FIG. B
Once in the desired position, tighten
screws to the radio chassis (top) and
mounting bracket assembly (bottom).
Remove the display from the bracket
assembly by lifting upward and
unhooking.
Note: There are multiple mounting
holes on the mounting bracket to allow
adjusting the mounting depth.
Note: If you encounter a depth issue with
the radio module in the top position, you
may move it to the bottom location by
inverting the mounting bracket assembly.
(FIG. C)
Note: The boot is not required if display
sits very close to the dash/dash kit and
no large gap is seen.
HOOK BOTTOM
FIRST, THEN TOP
NOTE: BOOT AND DASH KIT (NOT SHOWN)
FIG. C
6
Page 7
BOOT ASSEMBLY PLASTIC "TAB"
HAS TO GO INTO A NOTCH
(DISPLAY UNIT NOT SHOWN)
BOOT ASSEMBLY HOOKS
AT 5 SPOTS
(RUBBER BOOT NOT SHOWN)
BOOT ASSEMBLY HOOKS
AT 5 SPOTS
(RUBBER BOOT NOT SHOWN)
4
ASSEMBLY AND MOUNTING
Using Double DIN Dash Kit
B
Insert a M5 X 10 on each side of the clamp
assembly. Use Hole A for no vertical tilt
or Hole B for 8 degrees of vertical tilt as
determined in Step 3.
A
5
6
If needed, attach the rubber boot to
the display clamp assembly by aligning
the notch on the top edge as shown,
and hook the boot to the clamp at 5
locations.
Note: The boot is not required if display
sits very close to the dash/dash kit and
no large gap is seen.
After all wiring connections are made
in the next section, the dash kit with the
radio chassis and bracket assembly,
should be installed and any factory
panels reinstalled. Connect the 8 Pin
Display Power Harness and the LVDS
Video Cable to the back of the display
and attach display to mounting bracket.
7
Page 8
WIRING & CONNECTIONS
Display Cable
Power / Speaker
GPS Antenna
15 Amp Fuse
AV In/Out - Rear Camera Microphone
2
USB1 CP/AA
16 Pin Power / Speaker Harness
Connect radio power and
speaker connections to a vehicle
specific harness (sold separately)
referencing diagram at right.
USB2
Multi Camera
1
SWI
HDMI Input
SiriusXM Tuner
TOSLINK
LVDS Cable
Radio Antenna
Green/Black Rear Left Speaker -
Green Rear Left Speaker +
Purple/Black Rear Right Speaker -
Purple Rear Right Speaker +
White/Black Front Left Speaker -
1
The top USB1 must be used for CarPlay
and Android Auto.
2
GPS Antenna must be installed for accurate
operation of CarPlay, Android Auto & internal
Navigation.
3
Illumination wire must be connected for
Day/Night and Auto Dimming to work.
8
White Front Left Speaker +
Grey/Black Front Right Speaker -
Grey Front Right Speaker +
Green/White Reverse Trigger +
Pink Parking Brake -
Orange Illumination3 +
Yellow Battery 12V +
Blue Power Antenna +
Blue/White Amp Remote +
Red Accessory 12V +
Black Ground -
Page 9
A1 Brown / Black SWC Key 2
A2 Brown SWC Key 1
A3 Black SWC Ground
A4 Yellow RCA Video Input
A5 White RCA Audio Input Left
A6 Red RCA Audio Input Right
A7 Yellow RCA Camera Input
A8 Yellow RCA Video Output 1
A9 Yellow RCA Video Output 2
A10 White RCA Zone 2 Left
A11 Red RCA Zone 2 Right
A12 Red RCA Right front
A13 White RCA Left Front
A14 Red RCA Right Rear
A15 White RCA Left Rear
A16 Brown RCA Left Subwoofer
A17 Blue RCA Right Subwoofer
WIRING & CONNECTIONS
24 Pin AV / Rear Camera Harness
Audio/Video Inputs & Outputs / Rear Camera Video Input /
Analog Steering Wheel Control Inputs.
Analog Steering
Wheel Control Input
Audio / Video Input
Video Output
Audio Output
SiriusXM® Harness
For connecting optional SiriusXM
SXV 300 satellite radio tuner.
9
Page 10
A1 Steering Wheel Control Input
A2 IR Input
A1 Camera Audio Input
A2 Mic Input
A1 Camera 2 Input
A2 Camera 3 Input
A3 Camera 4 Input
C1 Camera 3 Trigger
C2 Camera 4 Trigger
C3 Camera 2 Trigger
C4 Vehicle Speed input
D Expansion Port (PAC Interface)
WIRING & CONNECTIONS
6 Pin SWI / IR Harness
3.5mm Input for optional Steering Wheel Control Interface
(PAC Audio SWI-CP2 is recommended for full compatibility and advanced features. Visit PAC-Audio.com)
- Not Used
4 Pin Microphone / Camera Audio Harness
Input for External Microphone (included) used for hands-free calling, CarPlay and Android Auto
Optional rear camera audio input
Camera #1 Audio Input
Microphone Input
10 Pin Multi Camera Harness
3 additional camera inputs and triggers / VSS / Expansion Port
Camera Triggers 2 & 3 will accept a pulsing + trigger (turn signal).
D
10
Video
Video
Video
+
+
+
Page 11
Navigation Ready
Front of radio module
Adding optional iGo Navigation is as easy
as sliding in a Micro SD card into the front
of the radio module. ELEV8 and iGO are
optimized for ease of use and driving safety.
Best Kits
Dash kits, wire harnesses and antenna
adapters. PAC-Audio.com
UPGRADES & OPTIONS
Navigation SD Card
PAC Audio
Retain the factory vehicle features with
RadioPRO Radio Replacement Modules,
Steering Wheel Interfaces, Factory Camera
and USB retention. PAC-Audio.com
EchoMaster
Add a Rear Camera, or Side and Front
Cameras. EchoMaster.com
Phoenix Gold
Take advantage of the 6 channel / 4v
outputs by adding an amp and speakers.
PhoenixGold.com.com
Page 12
StingerElectronics.com
Copyright © 2018
IG-UN1880-REV.092518
Loading...