Stihl HT 56 C User Manual

STIHL HT 56 C
WARNING
Read Instruction Manual thoroughly before use and follow all safety precautions – improper use can cause serious or fatal injury.
Antes de usar la máquina lea y siga todas las precauciones de seguridad dadas en el manual de instrucciones – el uso incorrecto puede causar lesiones graves o mortales.
{
Instruction Manual Manual de instrucciones
G Instruction Manual
1 - 45
U Manual de instrucciones
46 - 94
Contents
English
Guide to Using this Manual 2 Safety Precautions and Working
Techniques 3 Using the Unit 13 Assembling the Unit 15 Cutting Attachment 16 Mounting the Bar and Chain 16 Tensioning the Chain 17
Original Instruction ManualPrinted on chlorine-free paper
Checking Chain Tension 18 Fuel 18 Fueling 19 Chain Lubricant 20 Filling Chain Oil Tank 20 Checking Chain Lubrication 22 Fitting the Harness 23 Starting / Stopping the Engine 23 Transporting the Unit 25 Operating Instructions 26 Taking Care of the Guide Bar 27 Cleaning the Air Filter 27 Engine Management 28 Adjusting the Carburetor 28
Printing inks contain vegetable oils, paper can be recycled.
Spark Plug 29 Storing the Machine 30 Checking and Replacing the Chain
Sprocket 30 Maintaining and Sharpening the
Saw Chain 31 Inspections and Maintenance by
Dealer 35 Maintenance and Care 36 Main Parts 38
Specifications 40 Maintenance and Repairs 41 Disposal 41 Limited Warranty 41 STIHL Incorporated Federal
Emission Control Warranty Statement 42
Trademarks 44
Allow only persons who fully understand this manual to operate your pole pruner.
To receive maximum performance and satisfaction from your STIHL pole pruner, it is important that you read, understand and follow the safety precautions and the operating and maintenance instructions in chapter "Safety Precautions and Working Techniques" before using your pole pruner. For further information you can go to www.stihlusa.com.
Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in this manual.
WARNING
Because a pole pruner is a high-speed, fast-cutting power tool with an extended reach, special safety precautions must be observed to reduce the risk of personal injury. Careless or improper use may cause serious or even fatal injury.
{
© ANDREAS STIHL AG & Co. KG, 2017
0458-555-8621-D. VA1.A17.
0000007134_003_GB
HT 56 C
This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems.
1
English
Guide to Using this Manual
Pictograms
The meanings of the pictograms attached to or embossed on the machine are explained in this manual.
Depending on the model concerned, the following pictograms may be on your machine.
Fuel tank for gasoline and engine oil mixture
Tank for bar and chain oil
Direction of chain rotation
Press to operate manual fuel pump
Manual fuel pump
A description of a step or procedure that refers directly to an illustration may contain item numbers that appear in the illustration. Example:
N Loosen the screw (1). N Lever (2) ...
In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the symbols and signal words described below:
DANGER
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
NOTICE
Indicates a risk of property damage, including damage to the machine or its individual components.
described in this manual, please contact your STIHL dealer or the STIHL distributor for your area for assistance.
Symbols in Text
Many operating and safety instructions are supported by illustrations.
The individual steps or procedures described in the manual may be marked in different ways:
N A bullet marks a step or procedure.
2
Engineering Improvements
STIHL’s philosophy is to continually improve all of its products. As a result, engineering changes and improvements are made from time to time. Therefore, some changes, modifications and improvements may not be covered in this manual. If the operating characteristics or the appearance of your machine differs from those
HT 56 C
English
Safety Precautions and Working Techniques
Because a pole pruner is a high-speed, fast-cut­ting power tool with an extended reach, special safety precautions must be observed to reduce the risk of personal injury.
It is important that you read, fully understand and observe the following safety precautions and warnings. Read the instruction manual and the safety precautions periodically. Careless or improper use may cause serious or fatal injury.
Have your STIHL dealer show you how to operate your power tool. Observe all applicable national, state and local laws, safety regulations, standards and ordinances.
WARNING
Do not lend or rent your power tool without the instruction manual. Be sure that anyone using it understands the information contained in this manual.
WARNING
The use of this machine may be hazardous. The pole pruner chain has many sharp cutters. If the cutters contact your flesh, they will cut you, even if the chain is not moving.
WARNING
Do not cut any material other than wood or wooden objects. Use your pole pruner for limbing only.
Do not use it for other purposes, since misuse may result in personal injury or property damage, including damage to the machine.
WARNING
Minors should never be allowed to use this power tool. Bystanders, especially children, and animals should not be allowed in the area where it is in use.
WARNING
To reduce the risk of injury to bystanders and damage to property, never let your power tool run unattended. When it is not in use (e. g. during a work break), shut it off and make sure that unauthorized persons do not use it.
Most of these safety precautions and warnings apply to the use of all STIHL pole pruners. Different models may have different parts and controls. See the appropriate section of your instruction manual for a description of the controls and the function of the parts of your model.
Safe use of a pole pruner involves
1. the operator
2. the pole pruner
3. the use of the pole pruner.
THE OPERATOR
Physical Condition You must be in good physical condition
and mental health and not under the influence of any substance (drugs, alcohol, etc.) which might impair vision, dexterity or judgment. Do not operate this machine when you are fatigued.
WARNING
Be alert – if you get tired, take a break. Tiredness may result in loss of control. Working with any power tool can be strenuous. If you have any condition that might be aggravated by strenuous work, check with your doctor before operating this machine.
WARNING
Prolonged use of a power tool (or other machines) exposing the operator to vibrations may produce whitefinger disease (Raynaud's phenomenon) or carpal tunnel syndrome.
These conditions reduce the hand's ability to feel and regulate temperature, produce numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis.
All factors which contribute to whitefinger disease are not known, but cold weather, smoking and diseases or physical conditions that affect blood vessels and blood transport, as well as high vibration levels and long periods of
HT 56 C
3
English
exposure to vibration are mentioned as factors in the development of whitefinger disease. In order to reduce the risk of whitefinger disease and carpal tunnel syndrome, please note the following:
Most STIHL power tools are
available with an anti-vibration ("AV") system designed to reduce the transmission of vibrations created by the machine to the operator's hands. An AV system is recommended for those persons using power tools on a regular or sustained basis.
Wear gloves and keep your hands
warm.
Keep the AV system well
maintained. A power tool with loose components or with damaged or worn AV elements will tend to have higher vibration levels.
Maintain a firm grip at all times, but
do not squeeze the handles with constant, excessive pressure. Take frequent breaks.
All the above-mentioned precautions do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome. Therefore, continual and regular users should closely monitor the condition of their hands and fingers. If any of the above symptoms appear, seek medical advice immediately.
WARNING
The ignition system of the STIHL unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with a pacemaker should
consult their physician and the pacemaker manufacturer before operating this tool.
Proper Clothing
WARNING
To reduce the risk of injury, the operator should wear proper protective apparel.
WARNING
To reduce the risk of injury to your eyes never operate your power tool unless wearing goggles or properly fitted protec­tive glasses with adequate top and side protection complying with ANSI Z87 "+" (or your applicable national stand­ard). To reduce the risk of injury to your face STIHL recommends that you also wear a face shield or face screen over your goggles or protective glasses.
Wear an approved safety hard hat to reduce the risk of injury to your head.
Power tool noise may damage your hearing. Wear sound barriers (ear plugs or ear mufflers) to protect your hearing. Continual and regular users should have their hearing checked regularly.
Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings (shouts, alarms, etc.) is restricted.
Always wear heavy-duty work gloves (e.g. made of leather or other wear resistant material) when handling the machine and the cutting tool. Heavy-duty, nonslip gloves improve your grip and help to protect your hands.
Clothing must be sturdy and snug-fitting, but allow complete freedom of movement. Wear long pants made of heavy material to help protect your legs. Do not wear shorts, sandals or go barefoot.
Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, unconfined long hair or anything that could become caught on branches, brush or the moving parts of the unit. Secure hair so it is above shoulder level.
Good footing is very important. Wear sturdy boots with nonslip soles. Steel-toed safety boots with cut retardant inserts are recommended.
THE POWER TOOL
For illustrations and definitions of the power tool parts see the chapter on "Main Parts".
4
HT 56 C
English
275BA009 KN
WARNING
Never modify this power tool in any way. Only attachments supplied by STIHL or expressly approved by STIHL for use with the specific STIHL model are authorized. Although certain unauthorized attachments are useable with STIHL power tools, their use may, in fact, be extremely dangerous.
If this tool is subjected to unusually high loads for which it was not designed (e. g. heavy impact or a fall), always check that it is in good condition before continuing work. Check in particular that the fuel system is tight (no leaks) and that the controls and safety devices are working properly. Do not continue operating this machine if it is damaged. In case of doubt, have it checked by your STIHL servicing dealer.
THE USE OF THE POWER TOOL
Transporting the Power Tool
This power tool should be carried only in a horizontal position. Grip the shaft in a manner that the machine is balanced horizontally. Keep the hot muffler away from your body and the cutting attachment behind you.
WARNING
Accidental acceleration of the engine can cause the chain to rotate and cause serious injuries.
Always switch off the engine and fit the scabbard over the cutting attachment before transporting the power tool. When transporting it in a vehicle, properly secure it to prevent turnover, fuel spillage and damage to the unit.
Fuel Your STIHL power tool uses an oil-
gasoline mixture for fuel (see the chapter on "Fuel" in this instruction manual).
WARNING
Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and
serious burn injury or property damage. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape from the fuel system.
Fueling Instructions
WARNING
To reduce the risk of serious injury from burns, never attempt to refuel the unit until it has been completely removed from the operator.
WARNING
Fuel your power tool in well-ventilated areas, outdoors. Always shut off the engine and allow it to cool before refueling. Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used, the weather conditions and the tank venting system.
In order to reduce the risk of burns and other personal injury from escaping gas vapor and fumes, remove the fuel filler cap on your power tool carefully so as to allow any pressure build-up in the tank to release slowly. Never remove the fuel filler cap while the engine is running.
Select bare ground for fueling and move at least 10 feet (3 m) from the fueling spot before starting the engine. Wipe off any spilled fuel before starting your machine.
WARNING
Check for fuel leakage while refueling and during operation. If fuel leakage is found, do not start or run the machine until the leak is fixed and any leaked fuel has been wiped away. Take care not to get fuel on your clothing. If this happens, change your clothing immediately.
WARNING
In order to reduce the risk of fuel spillage and fire from an improperly tightened fuel cap, correctly position and tighten the fuel cap in the fuel tank opening.
HT 56 C
5
English
246BA034 KN
Screw Cap
WARNING
Unit vibrations can cause an improperly tightened fuel filler cap to loosen or come off and spill quanti­ties of fuel. In order to reduce the risk of fuel spillage and fire, tighten the fuel filler cap by hand as securely as possible.
See also the "Fueling" chapter in this instruction manual for additional information.
Before Starting Take off the chain guard (scabbard) and
inspect the pole pruner for proper condition and operation. (See the maintenance chart near the end of the instruction manual.)
WARNING
Always check your power tool for proper condition and operation before starting, particularly the throttle trigger, throttle trigger lockout, stop switch and cutting attachment. The throttle trigger must move freely and always spring back to the idle position. Never attempt to modify the controls or safety devices.
WARNING
Check fuel system for leaks, especially the visible parts, e.g., filler cap, hose connections, manual fuel pump (only for power tools equipped with a manual fuel pump). To reduce the risk of personal injury or property damage from fire, do
not start the engine if there are leaks or damage. Have the machine repaired by a servicing dealer before using it.
WARNING
Never operate your power tool if it is damaged, improperly adjusted or maintained, or not completely or securely assembled.
WARNING
Check that the spark plug boot is securely mounted on the spark plug – a loose boot may cause arcing that could ignite combustible fumes and cause a fire.
Keep the handles clean and dry at all times; it is particularly important to keep them free of moisture, pitch, oil, fuel mix, grease or resin in order for you to maintain a firm grip and properly control your power tool.
For proper assembly of the bar and chain follow the procedure described in the chapter "Mounting the Bar and Chain" of this instruction manual.
STIHL Oilomatic chain, guide bar and sprocket must match each other in gauge and pitch.
WARNING
Proper chain tension is extremely important. In order to avoid improper setting, the tensioning procedure must be followed as described in your manual. Always make sure the hex nut(s) for the sprocket cover is (are) tightened securely after tensioning the chain. Check chain tension once more
after having tightened the nut(s). Never start the pole pruner with the sprocket cover loose.
Adjust carrying harness (if applicable) and hand grip to suit your size before starting work.
Starting To reduce the risk of fire and burn
injuries, start the engine at least 10 feet (3 m) from the fueling spot, outdoors only.
For specific starting instructions, see the appropriate section of your manual. Proper starting methods reduce the risk of injury.
Place the pole pruner on firm ground or other solid surface in an open area or, in the alternative, as shown in the above picture. Maintain good balance and secure footing.
WARNING
To reduce the risk of injury from loss of control, do not attempt to "drop start" your power tool. Drop starting means pushing the machine away from the operator, or allowing it to drop toward the ground, while pulling on the starter
6
HT 56 C
English
390BA026 KN
grip. This method is very dangerous because you may lose control of the machine.
WARNING
To reduce the risk of injury from loss of control be absolutely sure that the guide bar and chain are clear of you and all other obstructions and objects, including the ground, because when the engine starts at starting-throttle, engine speed will be fast enough for the clutch to engage the sprocket and turn the chain.
Once the engine has started, immediately blip the throttle trigger, which should release the starting throttle and allow the engine to slow down to idle.
With the engine running only at idle, attach the power tool to the spring hook of your harness if you are wearing one (see appropriate chapter of this manual).
WARNING
Your power tool is a one-person machine. Do not allow other persons in the general work area, even when starting. Stop the engine immediately if you are approached.
WARNING
When you pull the starter grip, do not wrap the starter rope around your hand. Do not let the grip snap back, but guide the starter rope to permit the rope to rewind. Failure to follow this procedure may result in injury to your hand or fingers and may damage the starter mechanism.
Important Adjustments
WARNING
To reduce the risk of personal injury from loss of control or contact with the running cutting tool, do not use your unit with incorrect idle adjustment. At correct idle speed, the saw chain should not move. For directions on how to adjust idle speed, see the appropriate section of your instruction manual.
If you cannot set the correct idle speed, have your STIHL dealer check your power tool and make proper adjustments and repairs.
WARNING
This unit is equipped with an ignition system that is normally in operational readiness. After the setting lever is used to stop the engine, it automatically springs back to the "on" position. If the engine is warm, it may be possible to start it by simply pulling the starter rope, with no further adjustments. To reduce the risk of injury, be particularly alert to keep children away from the unit.
Proper chain tension is very important at all times. Check it at regular intervals (during work breaks and only when the pole pruner is shut off). If the chain becomes loose while cutting, switch off the engine and then tighten. Never try to tighten the chain while the engine is running.
During Operation Holding and Controlling the Power Tool Always hold the unit firmly with both
hands on the handles while you are working. Wrap your fingers and thumbs around the handles.
Place your left hand on the shaft and your right hand on rear grip and throttle trigger. Left-handers must follow these instructions, too. Keep your hands in this position to help maintain control of your pole pruner while working at all times.
WARNING
Never attempt to operate your power tool with one hand. Loss of control of the power tool resulting in serious or fatal injury may result.
HT 56 C
7
English
WARNING
In order to properly control your pole pruner, always maintain good balance and a firm foothold. Never work on a ladder, in a tree or on any other insecure support. Never hold the machine above shoulder height. Do not overreach. When working at a height above
13.1 feet (4.0 m) use a lift bucket.
WARNING
Special care must be taken in slippery conditions (wet ground, snow) and in difficult, overgrown terrain. Watch for hidden obstacles such as tree stumps, roots, rocks, holes and ditches to avoid stumbling. For better footing, clear away fallen branches, scrub and cuttings. Be extremely cautious when working on slopes or uneven ground.
WARNING
Take extreme care in wet and freezing weather (rain, snow, ice). Put off the work when the weather is windy, stormy or rainfall is heavy.
Working Conditions Operate and start your power tool only
outdoors in a well-ventilated area. Operate it under good visibility and daylight conditions only. Work carefully.
WARNING
As soon as the engine is running, this product gen­erates toxic exhaust fumes containing chemi­cals, such as unburned hydrocarbons (including benzene) and carbon monoxide, that are known to cause respira­tory problems, cancer, birth defects, or other reproductive harm. Some of the gases (e. g. carbon monoxide) may be color­less and odorless and can cause asphyxiation or death very quickly. To reduce the risk of serious or fatal injury/illness from inhaling toxic fumes, never run the machine indoors or in poorly venti­lated locations. If exhaust fumes become concen­trated due to insufficient ventilation, clear obstruc­tions from work area to permit proper ventilation before proceeding and/or take frequent breaks to allow fumes to dissipate before they become concentrated.
WARNING
Inhalation of certain dusts, especially organic dusts such as mold or pollen, can cause susceptible persons to have an allergic or asthmatic reaction. Substantial or repeated inhalation of dust and other airborne contaminants, in
particular those with a smaller particle size, may cause respiratory or other illnesses. This includes wood dust, especially from hardwoods, but also from some softwoods such as Western Red Cedar. Control dust at the source where possible. Use good work practices, such as always cutting with a properly sharpened chain (which produces wood chips rather than fine dust) and operating the unit so that the wind or operating process directs any dust raised by the power tool away from the operator. Follow the recommendations of EPA/OSHA/NIOSH and occupational and trade associations with respect to dust ("particulate matter"). When the inhalation of dust cannot be substantially controlled, i.e., kept at or near the ambient (background) level, the operator and any bystanders should wear a respirator approved by NIOSH/MSHA for the type of dust encountered.
WARNING
Breathing asbestos dust is dangerous and can cause severe or fatal injury, respiratory illness or cancer. The use and disposal of asbestos-containing products have been strictly regulated by OSHA and the Environmental Protection Agency. If you have any reason to believe that you might be cutting asbestos, immediately contact your employer or a local OSHA representative.
8
HT 56 C
English
15m (50ft)
15m (50ft)
WARNING
This power tool has a large range. In order to reduce the risk of personal or even fatal injury to bystanders from falling objects or inadvertent contact with the moving chain of your power tool always keep bystanders at least 50 feet (15 m) away when the power tool is running.
WARNING
Even though bystanders should be kept away from the running saw chain, never work alone. Keep within calling distance of others in case help is needed.
Stop the engine immediately if you are approached.
DANGER
Your power tool is not insulated against electric shock. To reduce the risk of electrocution, never operate this power tool in the vicinity of any wires or cables (power, etc.) which may be carrying electric current.
Electricity can jump from one point to another by means of arcing. Higher voltage increases the distance electricity can arc. Electricity can also move through branches, especially if they are wet. Maintain a clearance of at least 50 feet (15 m) between the pole pruner (including any branches it is contacting) and any electrical line carrying live current. Before working with less clearance, contact your electric utility and make sure the current is turned off.
Operating Instructions
WARNING
Do not operate your power tool using the starting throttle lock, as you do not have control of the engine speed.
In the event of an emergency, switch off the engine immediately – move the slide control / stop switch to 0 or STOP.
WARNING
To reduce the risk of cut injuries, keep hands and feet away from the saw chain. Never touch a moving chain with your hand or any other part of your body. The saw chain continues to move for a short period after the throttle trigger is released (inertia effect).
Accelerating the engine while the chain is blocked increases the load and will cause the clutch to slip continuously. This may result in overheating and damage to important components (e. g. clutch, polymer housing components) – which can then increase the risk of injury from the chain moving while the engine is idling.
WARNING
If the chain becomes clogged, always turn off the engine and make sure the chain has stopped before cleaning.
Make sure that the saw chain does not touch any foreign materials such as rocks, fences, nails and the like. Such objects may be flung off and injure the operator or bystanders, or damage the saw chain.
HT 56 C
9
English
246BA030 KN
WARNING
Prior to limbing, clear the working area from interfering limbs and brush. Then, establish an escape area away from where the cut limbs can fall, and remove all obstacles.
Keep work area clear – move away fallen limbs. Place all tools and equipment at a safe distance from the branches being limbed, but not in the escape area.
WARNING
Always observe the general condition of the tree. Look for decay and rot in the trunk and branches. If it is rotted inside, it could snap and fall toward the operator while being cut. Also look for broken or dead branches which could vibrate loose and fall on the operator. If branch is thick or heavy, make a shallow relief cut on the bottom of the branch before cutting down from the top to help prevent splitting of the branch. See chapter on "Using the Unit".
WARNING
To reduce the risk of severe or even fatal injury from falling objects do not cut vertically above your body. Hold the pole pruner at an angle of not more than 60° from the horizontal level (see picture). Objects may fall in unexpected directions. Do not stand directly underneath the limb being cut!
Watch for falling wood! As soon as the limbed branch starts to fall, step aside and keep a sufficient distance away from the falling wood.
WARNING
Always pull the unit out of the cut with the chain running to reduce the possibility of pinching the cutting attachment. Don't put pressure on the pole pruner when reaching the end of a cut. The pressure may cause the bar
and rotating chain to pop out of the cut or kerf, go out of control and strike some other object.
If the bar becomes pinched and caught in the branch so that the chain can no longer move, shut off the pole pruner and carefully move the branch to open the pinch and release the bar.
WARNING
If a rotating saw chain strikes a rock or other hard object, sparks may be created, which can ignite flammable materials under certain circumstances. Flammable materials can include dry vegetation and brush, particularly when weather conditions are hot and dry. When there is a risk of fire or wildfire, do not use a power tool around flammable materials or around dry vegetation or brush. Contact your local fire authorities or the U.S. Forestry Service if you have any question about whether vegetation and weather conditions are suitable for the use of a pole pruner.
WARNING
Never modify your muffler. Any modification could cause an increase in heat radiation, sparks or sound level, thereby increasing the risk of fire, burn injury or hearing loss. You may also permanently damage the engine. Have your muffler serviced and repaired by your STIHL servicing dealer only.
WARNING
The muffler and other parts of the engine (e.g. fins of the cylinder, spark plug) become hot during operation and remain hot for a while after stopping the engine.
10
HT 56 C
English
002BA230 KN
001BA037 KN
A
To reduce risk of burns, do not touch the muffler and other parts while they are hot. Keep the area around the muffler clean. Remove excess lubricant and all debris such as pine needles, branches or leaves. Let the engine cool down sitting on concrete, metal, bare ground or solid wood (e.g. the trunk of a felled tree) away from any combustible substances.
WARNING
An improperly mounted or damaged cylinder housing or a damaged/deformed muffler shell may interfere with the cooling process of the muffler. To reduce the risk of fire or burn injury, do not continue work with a damaged or improperly mounted cylinder housing or a damaged/deformed muffler shell.
Your muffler is furnished with a spark arresting screen designed to reduce the risk of fire from the emission of hot particles. Never operate your unit with a missing or damaged spark arresting screen. If your gas/oil mix ratio is correct (i.e., not too rich), this screen will normally stay clean as a result of the heat from the muffler and need no service or maintenance. If you experience loss of performance and you suspect a clogged screen, have your muffler maintained by a STIHL servicing dealer. Some state or federal laws or regulations may require a properly maintained spark arrestor for certain uses. See the "Maintenance, Repair and Storing" section of these Safety Precautions. Remember that the risk of a brush or forest fire is greater in hot or dry conditions.
Reactive Forces
WARNING
Reactive forces may occur any time the chain is rotating.The force used to cut wood can be reversed and work against the operator. If the rotating chain is suddenly stopped by contact with any solid object such as a branch or is pinched, the reactive forces may occur instantly. These reactive forces may result in loss of control, which, in turn, may cause personal injury. An understanding of the causes of these reactive forces may help you avoid the element of surprise and loss of control.
Because of the design of the pole pruner, the reactive forces experienced when working with it are generally not as severe as those encountered with a chain saw. Nevertheless, you should always maintain a proper grip and good footing to control the power tool when you experience such forces.
The most common reactive forces are:
kickback, pushback, pull-in.
Kickback Kickback may occur when the moving
saw chain near the upper quadrant of the bar nose contacts a solid object or is pinched.
The reaction of the cutting force of the chain causes a rotational force on the pole pruner in the direction opposite to the chain movement. This may cause the bar to move upward.
To Avoid Kickback The best protection from kickback is to
avoid kickback situations:
1. Be aware of the location of the guide bar nose at all times.
2. Never let the nose of the guide bar contact any object. Do not cut limbs with the nose of the guide bar. Be especially careful near wire fences and when cutting small, tough limbs, which may easily catch the chain.
3. Cut only one limb at a time.
A = Pull-in
Pull-in occurs when the chain on the bottom of the bar is suddenly stopped when it is pinched, caught or encounters
HT 56 C
11
English
001BA038 KN
B
a foreign object in the wood. The reaction of the chain pulls the pole pruner forward.
Pull-in frequently occurs when the chain is not rotating at full speed before it contacts the wood.
To Avoid Pull-in
1. Be alert to forces or situations that may cause material to pinch the chain at the bottom of the bar.
2. Always start a cut with the chain rotating at full speed.
B = Pushback
Pushback occurs when the chain on the top of the bar is suddenly stopped when it is pinched, caught or encounters a foreign object in the wood. The reaction of the chain may drive the pole pruner rapidly straight back toward the operator. Pushback frequently occurs when the top of the bar is used for cutting.
To Avoid Pushback
1. Be alert to forces or situations that may cause material to pinch the chain at the top of the bar.
2. Do not cut more than one limb at a time.
3. Do not twist the bar when withdrawing it from an underbuck cut because the chain can pinch.
MAINTENANCE, REPAIR AND STORING
Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, if you make a warranty claim for a component which has not been serviced or maintained properly, STIHL may deny coverage.
WARNING
STIHL recommends the use of STIHL replacement parts for maintenance and repair. Use of parts manufactured by others may be extremely dangerous and could result in serious or fatal injury.
Strictly follow the maintenance and repair instructions in the appropriate sections of this instruction manual. Please refer to the maintenance chart in this manual.
WARNING
Always stop the engine and make sure that the chain is stopped before doing any maintenance or repair work or cleaning the power tool. Do not attempt any maintenance or repair work not
described in this instruction manual. STIHL recommends that you have such work performed by your STIHL servicing dealer.
Wear gloves when handling or performing maintenance on the cutting attachment.
WARNING
To reduce the risk of fire and burn injury or property damage, use only spark plugs authorized by STIHL. Always press spark plug boot snugly onto spark plug terminal of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be securely attached.) A loose connection between spark plug terminal and the ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. Keep the spark plug clean and make sure the ignition lead is in good condition.
WARNING
Never test the ignition system with the ignition wire boot removed from the spark plug or with a removed spark plug, since uncontained sparking may cause a fire.
WARNING
Do not operate your power tool if the muffler is damaged, missing or modified. An improperly maintained muffler will increase the risk of fire and hearing loss. Your muffler is equipped with a spark­arresting screen to reduce the risk of fire; never operate your power tool if the screen is missing, damaged or clogged.
12
HT 56 C
English
Remember that the risk of a brush or forest fire is greater in hot or dry weather.
In California, it is a violation of § 4442 or
§ 4443 of the Public Resources Code to use or operate gasoline-powered tools on forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a complying spark arrester that is maintained in effective working order. The owner/operator of this product is responsible for properly maintaining the spark arrester. Other states or governmental entities/agencies, such as the U.S. Forest Service, may have similar requirements. Contact your local fire agency or forest service for the laws or regulations relating to fire protection requirements.
WARNING
Keep the chain, bar and sprocket clean; replace worn sprockets or chains. Keep the chain sharp. You can spot a dull chain when easy-to-cut wood becomes hard to cut or burn marks appear on the wood. Keep chain at proper tension.
Tighten all nuts, bolts and screws except the carburetor adjustment screws after each use.
For maintenance items please also refer to the maintenance chart in this manual.
Do not clean your machine with a pressure washer. The solid jet of water may damage parts of the machine.
Store the power tool in a dry and high or locked location out of reach of children.
Before storing for longer than a few days, always empty the fuel tank. See chapter "Storing the machine" in this manual.
Store fuel and chain oil in approved and properly labeled safety-type canisters only. Take care when handling gasoline! Avoid direct contact with the skin and avoid inhaling fuel vapor!
Using the Unit
Preparations
N Wear suitable protective clothing,
observe safety precautions.
N Start the engine. N Put on the shoulder strap.
Cutting Sequence
To allow branches to free fall, always cut the lower branches first. Prune heavy branches (large diameter) in several controllable pieces.
WARNING
Never stand directly underneath the branch you are cutting – be wary of falling branches. Note that a branch may spring back at you after it hits the ground – risk of injury.
Disposal
Do not throw cuttings into the garbage can – they can be composted.
Working Techniques
Hold the control handle with your right hand, and the shaft with your left hand. Your left arm should be extended to the most comfortable position.
Always hold the shaft with your left hand in the area of the handle hose.
HT 56 C
13
English
246BA030 KN
246BA032 KN
2
1
246BA033 KN
3
4
A
390BA024 KN
The shaft should always be held at an angle of 60° or less.
The least tiring working position is a tool angle of 60°.
Any lesser angle may be used to suit the situation.
Cross-cut
Relieving cut
To avoid tearing the bark on thick branches, always start by performing a relieving cut (1) on the underside of the branch.
N To do this, apply the cutting
attachment and pull it across the bottom of the branch in an arc as far as the bar nose.
N Perform the cross cut (2) – position
the bar with the housing against the branch.
Flush-cutting thick branches
If branch diameter is more than 10 cm (4 in), first
N perform undercut (3) and then
cross-cut at a distance of about 20 cm/8 in (A) from the final cut. Then carry out the flush-cut (4), starting with a relieving cut and finishing with a cross-cut.
To avoid pinching the bar in the cut, position the cutting attachment with the housing against the branch and then perform the cross-cut from the top downwards.
14
HT 56 C
English
4907BA017 KN
1
4907BA008 KN
2
4907BA009 KN
4
3
6
5
4907BA010 KN
Cutting above obstacles
The machine's long reach makes it possible to prune branches that are overhanging obstacles, such as rivers or lakes. The tool angle in this case depends on the position of the branch.
Cutting from a lift bucket
Assembling the Unit
The unit features a split drive tube that helps save space during transportation. It unit can be easily disassembled for transportation – see “Transporting the Power Tool".
Connecting the Drive Tube
0000-GXX-2158-A0
WARNING
Do not mount KombiTools – only use the drive tube with splined shaft supplied with the machine.
N Slide the lug (2) on the front drive
tube (3) into the slot (4) in the coupling sleeve as far as stop – if necessary, turn the front drive tube (3) back and forth while pushing it home.
When correctly installed, the red line (5) (arrow point) must be flush with the end of the coupling sleeve.
N Tighten down the wing screw (6)
firmly.
N Attach the harness to the carrying
ring.
The machine's long reach enables cutting to be performed next to the trunk without the risk of the lift bucket damaging other branches. The tool angle in this case depends on the position of the branch.
HT 56 C
0000-GXX-2159-A0
N Pull the cap (1) off the end of the
front drive tube and keep it in a safe place for later use – see "Storing the Machine".
N Put the powerhead on the ground so
that it rests on the machine support.
15
English
001BA248 KN
1
2
3
a
001BA244 KN
246BA021 KN
1
2
246BA022-A1
Cutting Attachment
A cutting attachment consists of the saw chain, guide bar and chain sprocket.
The cutting attachment that comes standard is designed to exactly match the pole pruner.
The pitch (t) of the saw chain (1),
chain sprocket and the nose sprocket of the Rollomatic guide bar must match.
The drive link gauge (2) of the saw
chain (1) must match the groove width of the guide bar (3).
If non-matching components are used, the cutting attachment may be damaged beyond repair after a short period of operation.
Chain scabbard
Your pole pruner comes standard with a chain scabbard that matches the cutting attachment.
If you use guide bars of different lenghts on the pole pruner, the length of the chain scabbard must be matched to the guide bar to reduce the risk of injury. It should cover the full length of the guide bar.
The length of the matching guide bars is marked on the side of the chain scabbard.
Mounting the Bar and Chain
Removing the Chain Sprocket Cover
N Unscrew the nut and remove the
chain sprocket cover.
N Turn the screw (1) clockwise until
the tensioner slide (2) butts against the right end of the housing slot.
16
HT 56 C
English
390BA003 KN
1
246BA024 KN
Fitting the Chain
WARNING
Wear work gloves to protect your hands from the sharp cutters.
N Fit the chain – start at the bar nose.
1
5
3
4
N Fit the guide bar over the screw (3)
and engage peg of tensioner slide in the hole (4) – place the chain over the sprocket (5) at the same time.
N Turn the tensioning screw (1)
counterclockwise until there is very little chain sag on the underside of the bar – and the drive link tangs are engaged in the bar groove.
N Refit the sprocket cover and screw
on the nut fingertight.
N Go to chapter on "Tensioning the
Saw Chain".
Tensioning the Chain
246BA023 A1
Re-tensioning during cutting work:
N Shut off the engine. N Loosen the nut. N Hold the bar nose up. N Use a screwdriver to turn the
tensioning screw (1) counterclockwise until the chain fits snugly against the underside of the bar.
N While still holding the bar nose up,
tighten down the nut firmly.
N Go to "Checking Chain Tension". A new chain has to be re-tensioned
more often than one that has been in use for some time.
N Check chain tension frequently –
see chapter on "Operating Instructions".
HT 56 C
17
English
246BA025 KN
Checking Chain Tension
N Shut off the engine. N Wear work gloves to protect your
hands.
N The chain must fit snugly against
the underside of the bar and it must still be possible to pull the chain along the bar by hand.
N If necessary, re-tension the chain. A new chain has to be re-tensioned
more often than one that has been in use for some time.
N Check chain tension frequently –
see chapter on "Operating Instructions".
Fuel
This engine is certified to operate on unleaded gasoline and the STIHL two­stroke engine oil at a mix ratio of 50:1.
Your engine requires a mixture of high­quality gasoline and two-stroke air cooled engine oil.
Use mid-grade unleaded gasoline with a minimum octane rating of 89 ((R+M)/2) and no more than 10% ethanol content.
NOTICE
Fuel with an octane rating below 89 may increase engine temperatures. This, in turn, increases the risk of piston seizure and damage to the engine.
The chemical composition of the fuel is also important. Some fuel additives not only detrimentally affect elastomers (carburetor diaphragms, oil seals, fuel lines, etc.), but magnesium castings and catalytic converters as well. This could cause running problems or damage the engine. For this reason STIHL recommends that you use only quality unleaded gasoline!
NOTICE
Gasoline with an ethanol content of more than 10% can cause running problems and major damage in engines and should not be used.
For further details, see www.STIHLusa.com/ethanol
The ethanol content in gasoline affects engine speed – it may be necessary to readjust the carburetor if you use fuels with various ethanol contents.
WARNING
To reduce the risk of personal injury from loss of control and/or contact with the running cutting tool, do not use your unit with an incorrect idle adjustment. At correct idle speed, the cutting tool should not move.
If your machine’s idle speed is incorrectly adjusted, have your authorized STIHL servicing dealer check your machine and make the proper adjustments and repairs.
The idle speed and maximum speed of the engine change if you switch from a fuel with a certain ethanol content to a fuel with a much higher or lower ethanol content.
This problem can be avoided by always using fuel with the same ethanol content.
To ensure the maximum performance of your STIHL engine, use a high quality 2­cycle engine oil. To help your engine run cleaner and reduce harmful carbon deposits, STIHL recommends using STIHL HP Ultra 2-cycle engine oil or ask your dealer for an equivalent fully synthetic 2-cycle engine oil.
To meet the requirements of EPA and CARB we recommend to use STIHL HP Ultra oil.
STIHL MotoMix
STIHL recommends the use of STIHL MotoMix. STIHL MotoMix has a high octane rating and ensures that you always use the right gasoline/oil mix ratio.
18
HT 56 C
English
547BA045 KN
STIHL MotoMix uses STIHL HP Ultra two-stroke engine oil suited for high performance engines.
For further details, see www.STIHLusa.com/ethanol
If not using MotoMix, use only STIHL two-stroke engine oil or equivalent high­quality two-stroke engine oils that are designed for use in air cooled two-cycle engines.
The use of non-seasonal gasoline blends may increase the potential for pressure to build in the fuel tank during operation. For example, using a winder blend during the summer will increase pressure in the fuel tank. Always use gasoline blends appropriate to the season, altitude and other environmental factors.
Do not use BIA or TCW rated (two­stroke water cooled) mix oils or other mix oils that state they are for use in both water cooled and air cooled engines (e.g., outboard motors, snowmobiles, chain saws, mopeds, etc.).
WARNING
Take care when handling gasoline. Avoid direct contact with the skin and avoid inhaling fuel vapor. When filling at the pump, first remove the container from your vehicle and place the container on the ground before filling. To reduce the risk of sparks from static discharge and resulting fire and/or explosion, do not fill fuel containers that are sitting in or on a vehicle or trailer.
The container should be kept tightly closed in order to limit the amount of moisture that gets into the mixture.
The machine‘s fuel tank should be cleaned as necessary.
Fuel mix ages
If not using MotoMix, only mix sufficient fuel for a few days of work, not to exceed 30 days of storage. Store in approved fuel-containers only. When mixing, pour oil into the container first, and then add gasoline. Close the container and shake it vigorously by hand to ensure proper mix of oil and gasoline.
Gaso­line
Oil (STIHL 50:1 or equiva­lent high-quality oils)
US gal. US fl.oz.
12.6
2 1/2 6.4 5 12.8
Dispose of empty mixing-oil containers only at authorized disposal locations.
Fueling
Preparations
N Before fueling, clean the filler cap
and the area around it to ensure that no dirt falls into the tank.
Always thoroughly shake the mixture in the canister before fueling your machine.
N Position the machine so that the
filler cap is facing up.
WARNING
To reduce the risk of fire and personal injuries due to escaping fuel and vapor, remove the fuel filler cap carefully so that any excess pressure in the tank can escape slowly. Use the proper seasonal gasoline blend, i.e., winter blend in winter, summer blend in summer.
HT 56 C
19
English
002BA447 KN
002BA448 KN
246BA026 KN
Opening the threaded filler cap
N Turn the cap counterclockwise until
it can be removed from the tank opening.
N Remove the filler cap.
Refueling
Take care not to spill fuel while fueling and do not overfill the tank.
Closing the threaded filler cap
N Position cap. N Turn the cap clockwise as far as it
will go and tighten it as securely as possible by hand.
Chain Lubricant Filling Chain Oil Tank
For automatic and reliable lubrication of the chain and guide bar – use only an environmentally compatible quality chain and bar lubricant. Rapidly biodegradable STIHL BioPlus is recommended.
NOTICE
Biological chain oil must be resistant to aging (e.g. STIHL BioPlus), since it will otherwise quickly turn to resin. This results in hard deposits that are difficult to remove, especially in the area of the chain drive and chain. It may even cause the oil pump to seize.
The service life of the chain and guide bar depends on the quality of the lubricant. It is therefore essential to use only a specially formulated chain lubricant.
WARNING
Do not use waste oil. Renewed contact with waste oil can cause skin cancer. Moreover, waste oil is environmentally harmful.
NOTICE
Waste oil does not have the necessary lubricating properties and is unsuitable for chain lubrication.
NOTICE
A full chain oil tank is sufficient for only half a tankful of fuel. Check the oil level regularly during cutting work. Never allow the oil tank to run dry.
Preparations
N Thoroughly clean the tank cap and
the area around it to ensure that no dirt falls into the tank.
N Position the machine so that the
tank cap faces up.
20
HT 56 C
Opening
002BA575 KN
0000-GXX-0136-A0
0000-GXX-0137-A0 KN
0000-GXX-0138-A0 KN
0000-GXX-0137-A0 KN
0000-GXX-0139-A0 KN
0000-GXX-0140-A0 KN
0000-GXX-0141-A0 KN
English
N Raise the grip until it is upright.
N Turn the cap counterclockwise
(about a quarter turn).
Marks on tank cap and oil tank must line up.
N Remove the tank cap.
Filling the Chain Oil Tank
N Fill the tank with chain oil. Take care not to spill chain oil while
refilling and do not overfill the tank.
Closing
Grip must be vertical: N Fit the cap – marks on tank cap and
oil tank must line up.
N Press the cap down as far as stop.
N While holding the cap depressed,
turn it clockwise until it engages in position.
The marks on the cap and oil tank are then in alignment.
N Fold the grip down.
HT 56 C
21
English
0000-GX-0142 A0 KN
002BA584 KN
1
0000-GXX-0136-A0
246BA027 KN
Checking Chain Lubrication
Tank cap is locked. If the oil level in the tank does not go
down, the reason may be a problem in the oil supply system: Check chain lubrication, clean the oilways, contact your dealer for assistance if necessary. STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer.
If the tank cap cannot be locked in the oil tank opening
Bottom of cap is twisted in relation to top.
N Remove the cap from the oil tank
and check it from above.
Left: Bottom of cap is twisted –
inner mark (1) in line with outer mark.
Right: Bottom of cap in correct posi-
tion – inner mark is under the grip. It is not in line with the outer mark.
N Place the cap on the opening and
rotate it counterclockwise until it engages the filler neck.
N Continue rotating the cap
counterclockwise (about a quarter turn) – this causes the bottom of the cap to be turned to the correct position.
N Turn the cap clockwise and lock it in
position – see section on "Closing".
The saw chain must always throw off a small amount of oil.
NOTICE
Never operate your machine without chain lubrication. If the chain runs dry, the whole cutting attachment will be irretrievably damaged within a very short time. Always check chain lubrication and the oil level in the tank before starting work.
Every new chain has to be broken in for about 2 to 3 minutes.
After breaking in the chain, check chain tension and adjust if necessary – see "Checking Chain Tension".
22
HT 56 C
English
2
4907BA000 KN
1
3
1
2
4907BA001 KN
4
547BA015 KN
5
547BA016 KN
Fitting the Harness
The type and style of the shoulder strap depend on the market.
Shoulder strap
N Put on the shoulder strap (1). N Adjust the length of the strap. N With the power tool attached, the
carabiner (2) must be at about the same height as your right hip.
Starting / Stopping the Engine
Versions with Easy2Start
WARNING
This machine is extremely simple and easy to start, even for children.
To reduce the risk of serious or fatal injury:
do not allow children or other
unauthorized persons to attempt to start or otherwise use the machine
never allow children or
unauthorized persons access to the machine
never leave the machine
unattended while working or during work breaks
after work, store in a safe, secure
location out of the reach of children and other unauthorized persons
Controls
3 Stop switch with Run and 0 =Stop
positions.
Function of stop switch and ignition system
The stop switch is normally in the Run position, i.e. when it is not depressed: The ignition is switched on – the engine is ready to start. If the stop switch is moved to the 0 position, the ignition is switched off. The ignition is switched on again automatically after the engine stops.
Starting the Engine
N Press the manual fuel pump
bulb (4) at least five times – even if the bulb is filled with fuel.
HT 56 C
Cold engine (cold start)
1 Throttle trigger lockout 2 Throttle trigger
N Press in the choke knob (5) and turn
it to g at the same time.
23
English
5
547BA017 KN
246BA034 KN
547BA021 KN
Warm engine (warm start)
N Press in the choke knob (5) and turn
it to < at the same time.
Also use this setting if the engine has been running but is still cold.
Cranking
N Remove the chain guard.
N Place the machine on the ground: It
must rest securely on the engine support and the hook. If necessary, rest the hook on a raised support (e.g. a branch, mound or something similar). Check that the chain is not touching any object or the ground.
WARNING
Check that nobody is standing within the working range of the pruner.
N Make sure you have a safe and
secure footing.
N Hold the unit firmly on the ground
with your left hand and press down – do not touch the throttle trigger or throttle trigger lockout.
NOTICE
Do not stand or kneel on the shaft. N Hold the starter grip with your right
hand.
N Pull the starter grip steadily.
NOTICE
Do not pull out the starter rope all the way – it might otherwise break.
N Do not let the starter grip snap back.
Guide it slowly back into the housing so that the starter rope can rewind properly.
N Continue cranking until the engine
runs.
As soon as the engine runs
N Press down the throttle trigger
lockout and open the throttle – the choke knob moves to the run position F. After a cold start, warm up the engine by opening the throttle several times.
WARNING
Make sure the carburetor is correctly adjusted. The saw chain must not move when the engine is idling.
Your machine is now ready for operation.
Stopping the Engine
N Move the stop switch in the direction
of 0 – the engine stops – release the stop switch – it springs back to the run position.
Other Hints on Starting
Engine stalls in cold start position g or under acceleration.
N Move the choke knob to < and
continue cranking until the engine runs.
Engine does not start in warm start position <
N Move the choke knob to g and
continue cranking until the engine runs.
If the engine does not start
N Check that all settings are correct. N Check that there is fuel in the tank
and refuel if necessary.
N Check that the spark plug boot is
properly connected.
N Repeat the starting procedure.
24
HT 56 C
English
4907BA017 KN
1
4907BA005 KN
3
2
4
4907BA011 KN
5
4907BA006 KN
6
2
Fuel tank run until completely dry N After refueling, press the manual
fuel pump bulb at least five times – even if the bulb is already filled with fuel.
N Set the choke knob to suit the
engine temperature.
N Now start the engine.
Transporting the Unit
The unit features a split drive tube that helps save space during transportation.
Disconnecting the Drive Tube
N Disconnect the shoulder strap from
the carrying ring.
N Place the unit on the ground:
N Fit the cap (4) on the end of the
drive tube.
NOTICE
Make sure the ends of the drive tube are clean.
Connecting the Drive Tube
N Pull the cap off the drive tube and
keep it in a safe place.
N Put the powerhead on the ground so
that it rests on the machine support.
N Examine ends of drive tube for dirt
and clean if necessary.
HT 56 C
N Loosen the star knob (1) – do not
remove it.
N Pull the drive tube (2) out of the
coupling sleeve (3).
N Slide the lug (5) on the front drive
tube (2) into the slot (6) in the coupling sleeve as far as stop – if necessary, turn the front drive tube (2) back and forth while pushing it home.
25
English
7
4907BA007 KN
1
When correctly installed, the red line (7) (arrow point) must be flush with the end of the coupling sleeve.
N Tighten down the star knob (1)
firmly.
N Attach the harness to the carrying
ring.
Operating Instructions
During Break-In Period
A factory-new machine should not be run at high revs (full throttle off load) for the first three tank fillings. This avoids unnecessary high loads during the break-in period. As all moving parts have to bed in during the break-in period, the frictional resistances in the engine are greater during this period. The engine develops its maximum power after about 5 to 15 tank fillings.
During Operation
NOTICE
Do not make the mixture leaner to achieve an apparent increase in power – this could damage the engine – see "Adjusting the Carburetor".
Check chain tension frequently A new chain has to be retensioned more
often than one that has been in use for some time.
Chain cold Tension is correct when the chain fits
snugly against the underside of the bar and can still be pulled along the bar by hand. Retension if necessary – see "Tensioning the Saw Chain".
Chain at operating temperature The chain stretches and begins to sag.
The drive links must not come out of the bar groove – the chain may otherwise jump off the bar. Retension the chain – see "Tensioning the Saw Chain".
After long period of full-throttle operation Allow engine to run for a short while at
idle speed so that engine heat can be dissipated by the flow of cooling air. This protects engine-mounted components (ignition, carburetor) from thermal overload.
After Finishing Work
N Slacken off the chain if you have
retensioned it at operating temperature during cutting work.
NOTICE
Always slacken off the chain after finishing work. The chain contracts as it cools down. If it is not slackened off, it can damage the gear shaft and bearings.
Storing your saw for a short period Wait for the engine to cool down. Drain
the fuel tank. Store the machine in a dry location. Check the tightness of all accessible screws and nuts (not adjusting screws) at regular intervals and retighten if necessary.
Storing for a long period See chapter on "Storing the Machine"
26
HT 56 C
English
1
2
3
246BA028 KN
1
547BA022 KN
2
3
Taking Care of the Guide Bar
N Turn the bar over every time you
sharpen the chain and every time you replace the chain – this helps avoid one-sided wear, especially at the nose and underside of the bar.
N Regularly clean the oil inlet hole (1),
the oilway (2) and the bar groove (3).
N Measure the groove depth – with the
scale on the filing gauge (special accessory) – in the area used most for cutting.
The drive link tangs will otherwise scrape along the bottom of the groove – the cutters and tie straps will not ride on the bar rails.
Cleaning the Air Filter
If there is a noticeable loss of engine power
N Move the choke lever (1) to <. N Turn the screw (2) in the filter
cover (3) counterclockwise until the cover is loose.
N Ease the filter cover (3) over the
choke lever and lift it away.
N Clean away loose dirt from around
the filter.
Chain type Chain pitch Minimum
groove depth
Picco 1/4" P 4.0 mm
(0.16 in)
If groove depth is less than specified: N Replace the guide bar.
HT 56 C
27
English
547BA023 KN
4
0815BA006 KN
Engine Management Adjusting the Carburetor
N Reach into the recess (4) in the filter
housing and take out the felt filter (5).
N Fit a new felt filter element (5). As a
temporary measure you can knock it out on the palm of your hand or blow it out with compressed air. Do not wash.
NOTICE
Replace damaged parts. N Fit the felt filter (5) in the filter
housing, make sure it is properly seated – the arrow points to the recess.
N Move the choke lever (1) to <. N Fit the filter cover in position,
making sure the screw is square. Tighten down the screw.
Exhaust emissions are controlled by the design of the fundamental engine parameters and components (e.g. carburation, ignition, timing and valve or port timing) without the addition of any major hardware.
The carburetor comes from the factory with a standard setting.
On this machine it is no longer necessary to adjust the carburetor.
It has been set at the factory to provide an optimum fuel-air mixture in all locations and operating conditions.
Adjusting Idle Speed
Engine stops while idling
N Warm up the engine for about
3 minutes.
N Turn the idle speed screw (LA)
slowly clockwise until the engine runs smoothly – the saw chain must not rotate.
Chain rotates when engine is idling N Turn the idle speed screw (LA)
counterclockwise until the chain stops running and then turn the screw another 1/2 to 3/4 turn in the same direction.
28
HT 56 C
Loading...
+ 70 hidden pages