Stiga T8780Q Owner's Manual

Download

Page 1

TABLE TENNIS TABLE

MODEL NO.

T8780Q

OWNER'S MANUAL

1.Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2.Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons

before assembling or ordering parts.

3.To make assembly easier, use the Hardware Identifier on page 2 to identify and sort all

fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4.Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to

tighten them.

5.Tools required for assembly: Phillips Screwdriver, Two 9/16󰾾 Wrenches, Two 7/16󰾾 Wrenches.

Note: Adjustable wrenches can be substituted for wrenches.

6.Save this instruction manual and your proof of purchase (receipt) in the event that the

manufacturer has to be contacted for replacement parts.

Please Do Not Return This Product To The Store!

Contact Escalade® Sports customer service department at:

Phone:1-866-873-3528Toll – Free !

Fax:1-866-873-3533Toll – Free !

E-mail:tabletennis@escaladesports.com

Mailing Address (correspondence only):

Escalade Sports

PO Box 889

Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTINGTECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTSFREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE

SPORTS PRODUCT INFORMATION

2L-4153-00

Escalade® Sports products may be manufactured and/or licensed under the following patents.

6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563

Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2013 Escalade Sports

ÒÒ

Page 2

HARDWARE IDENTIFIER

3/8-16 x 3 1/2 Hex Head Bolt

(Qty. 4)

1/4-20 Nyloc

Locknut

(Qty. 8)

3/8-16

Nyloc

Locknut

(Qty. 4)

1/4-20 X 3 1/4 Carriage Bolt

#8-32 X 1 1/4

Sheet Metal Screw

(Qty. 4)

1/4-20 X 2 3/4 Hex Head Bolt

(Qty. 4)

3/4" Long Spacer

(Qty. 4)

3/8" Long Spacer

(Qty. 4)

1/4"

Plastic

Washer

(Qty. 4)

1/4-20 X 1 1/2 Phillips

Truss Head Screw

(Qty. 4)

1/4-20

Wing Nut

(Qty. 4)

#8 X 9/16

SMS

(Qty. 4)

3/8"

Plastic

Washer

(Qty. 8)

Page 3

READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)

ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!

1.Attach Wood Bottom Board (#15) to Caster Beam

Assemblies (#7) as shown in Figure 1. Turn

Caster Beams as shown and attach board with four

Carriage Bolts (#31) and four Wing Nuts (#32).

Tighten Thumb Screws securely.

Note: Support Plate (#43)

must be on inside of Caster

Rail (#7) as shown.

Figure 1

2.Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#7) as shown in Figure 2.

a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support

Plate (#43) and Caster Beam (#7) as shown in the Top View and Figure 2.

b) Slide one Hex Bolt (#27) through one linkage (#16) one Spacer (#36) pass through Caster Beam

(#7), followed by one Plastic Washer (#39), Strut Tube (#17), another Plastic Washer (#39), inner

Support Plate (#43) and Lock Nut (#28).

c) Repeat on other end of Caster Beam (#7) and on second Caster Beam.

d) Tighten Bolts (#13) and Nuts (#28) securely.

e) Tighten Nuts (#28) on Bolts (#27) securely.

NOTE: Tighten nuts so that end of Bolt (#27) in even with the edge of nut.

Note: Linkages & Strut

tubes must be turned as

shown or table will not

operate correctly.

Figure 2

Top View

(Inner Plate)

Page 4

3.Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the shipping container

to protect the painted surface of table top.

4.Rotate U-support (#21) that is on bottom of Table Top until you see the screw holes in the slots of U-

clips (#22). If necessary Slide U-support (#21) side to side and back and forth to see holes.

See Figure 3 & Detail A.

Note: To aid in assembly you can use a cordless drill and Phillips bit. Wear safety glasses.

5.Insert Screw (#35) through slot in U-clip (#22) and into U-support (#21). See Figure 3 &

Detail A. Thread screw all the way into U-support until it touches the back of the tube. There

should be about 3/8󰾾 of screw (#35) left sticking out. Repeat for second Screw (#35) and U

Clip (#22).

6.Repeat steps 3-5 on other table top assembly.

Note: Slide U-Support back and forth

until you see the hole if necessary.

Detail A

If you want to see a video on how to insert Screw (#35) go to:

http://www.escaladesports.com/customer-service/videos.html

Scan with your smartphone:

Figure 3

Page 5

7.Attach Table Top Assembly to Base Assembly as shown in

Figure 4. Pivot Strut Tubes (#17) up as shown; then, with

at least one adult on each side of Table Top, lift top and

align ends of U-support tube (#21) with tops of Strut

Tubes (#17) on Caster Beams (#7) as shown in Figure 4.

Slide tubes together.

DO NOT OPEN THE TABLE TO PLAYING POSITION

UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE

TABLE STANDING UNATTENDED. IT COULD BE

KNOCKED OVER CAUSING SERIOUS BODILY INJURY

OR PROPERTY DAMAGE.

AT LEAST TWO (2) ADULTS ARE NEEDED TO

COMPLETE THE REST OF THIS ASSEMBLY! WHEN

ASSEMBLING TOPS TO BASE, HANDLE TOP

ASSEMBLIES BY GRASPING ONLY THE TOPS

THEMSELVES. DO NOT GRASP METAL LEGS, U-

SUPPORT, LINKAGE, OR HINGES. THESE PARTS

CAN MOVE AND COULD PINCH FINGERS OR

HANDS CAUSING SERIOUS INJURY! ASSEMBLE

AS SHOWN WITH LEGS FULLY CLOSED AND

TOPS IN A VERTICAL POSITION. DO NOT OPEN

Y TO ASSEMBLE. TABLE TOPS ARELEGS AND TR

HEAVY -

ALONE!

DO NOT ATTEMPT TO ASSEMBLE

Table Top

Assembly

With at least 2 adults,

slide Table Top Assembly

onto Strut Tubes (#17).

Figure 4

U-Support

Strut Tube

PIVOT STRUT

TUBESUP

Strut Tube

Page 6

8.Secure U-support tube (#21) to Strut Tubes (#17) with two Screws

(#33) as shown in Figure 5. Align holes in U-support with holes in

Strut Tubes and thread screw (#33) into hole in Strut Tube (#17).

Tighten screws all the way but be careful not to over tighten as you

could strip threads on screws.

9.Attach Linkages (#16) to Leg (#19) as shown in Figure 5. Pivot Leg

(#19) out from the table top and pivot both linkages (#16) up and align

hole in Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg

(#19) using Hex Head Bolt (#29), Spacer (#37) and Locknut (#34).

Spacer (#37) goes between Linkage and Leg. Attach other Linkage to

Leg the same way. Tighten nuts securely.

DO NOT OPEN THE TABLE TO PLAYING

POSITION UNTIL BOTH TOPS ARE

INSTALLED! DO NOT LEAVE TABLE

STANDING UNATTENDED. IT COULD

BE KNOCKED OVER CAUSING SERIOUS

BODILY INJURY OR PROPERTY

DAMAGE.

Figure 5

Spacer goes between

Linkage Arm (#16) and

Leg (#19)

Page 7

DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL

BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE

STANDING UNATTENDED. IT COULD BE KNOCKED OVER

CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.

If you want to see a video on how to position hinge (#18) go to:

http://www.escaladesports.com/customer-service/videos.html

Scan with your smartphone:

Note:

If hinge (#18) is positioned as shown in Detail B, you will have to

rotate the hinge to the position shown in Detail C. DO NOT unscrew the

hinge, you can rotate the hinge without unscrewing it from the table.

10.Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 6 & Detail C.

With hinge positioned as shown, align hole in hinge with hole in Strut Tube and

attach with ¼󰾾 Screw (#30), Plastic Washer (#38) and Locknut (#34). Plastic

Washer (#38) goes between Strut Tube and Hinge. Tighten nut securely. Repeat

for other Hinge. CAUTION: Hinges must be positioned exactly as

shown or table will not operate correctly and could be damaged.

11. Attach Corner Protector (#40) to table corners. Push snap tabs on Corner Protector

into holes in rails. Be sure that tabs are aligned with holes before pushing.

You could break tabs if not aligned correctly.

12. With at least two adults, repeat steps 7 through 11 for other table top assembly.

ATTENTION: If hinge is positioned as

shown below (Detail B), Rotate the hinge

as shown in Detail C. Do not take hinge off.

Detail B

Incorrect position

of hinge

CAUTION: Position hinges exactly as

shown in Detail L or table will not

operate correctly and could be damaged.

Detail C

Correct position

of hinge

In the correct position

Hinge #18 will look like a

󰾽V󰾾 when attached to Strut

Tube (#17).

Figure 6

Plastic Washer goes

between Strut Tube

(#17) and Hinge (#18)

Hinge Assembly

Page 8

OPENING AND CLOSING INSTRUCTIONS

CAUTION:

EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR

CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE

TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.

DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL

DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.

TO OPEN:

1. Hold center of top edge. Gently pull outward to midway position.

....

Continue to pull until disengaged from plastic clips and legs rest on the

floor as shown in Figure 7A and 7B. Do not leave table partially

....

opened at midway position.

....

2. Lower second top as described in step 1.

3. Lock all four center hinges. See Figure 8.

4. Attach net posts and net to table as shown in Figure 9.

NOTE: Net will be tight. It will be necessary to stretch net. This will insure

proper net tension.

Plastic

Clip

Midway

Position

TO CLOSE:

1. Remove net and net posts from table.

2. Unlock all four hinges.

3. Lift one table half to midpoint until the

plastic clips are engaged. Then continue

lifting until closed.

4. Raise other table half in the same manner.

as shown in Figure 10.

....

Figure 9

Figure 7A

Figure 8

PLAYBACK POSITION

Push to lock hinge.

PLAYING POSITION

To lock hinge push up on

the table and push hinge

as shown in Figure 7B.

Hinge

Locked

Figure 7B

Figure 10

STORAGE POSITION

IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 11)

1. Set the table to the Playing Position and lock hinges as shown in

....

Figure 8.

2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create

....

enough slack to align table tops. See Figure 1.

3. With the help of two other adults, push the two table top halves so

....

they are in line with each other and re-tighten the Wing Nuts (#32) as

....

shown in Figure 11.

Figure 11

TOP VIEW

Page 9

ONE YEAR LIMITED WARRANTY

This consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTS Product

(hereinafter referred as the "Product").

WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original

purchase.

WARRANTY COVERAGE:ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from

defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE

PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW IN-

STRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORK-

MANSHIP.

WARRANTY PERFORMANCE:During the above one (1) year warranty period, ESCALADE SPORTS shall repair or replace with a

comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our

examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.

1-866-873-3528 / W

arranty Dept.

Or Write us at:

Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.

Or E-mail us at:

customerservice@escaladesports.com

Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTS

strongly recommends that the Product is insured for value prior to mailing.

WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE

ABOVE ONE (1) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR

OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.

Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above

limitations or exclusions may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.

CARE AND MAINTENANCE

You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table.

THE TABLE TOP

The top (playing surface) of your table is made of particle board or MDF. Like all products made of wood, it can be affected by atmospheric changes in both temperature and

humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value

of the table. After assembly of the table, you can minimize the effects of temperature and humidity changes by storing the table in the folded up position in a dry area when table

is not in use.

STORAGE OF YOUR TABLE

This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack or blister.

When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may bow. Damp and humid conditions will amplify this. This is

normal and will not affect playability of table.

CLEANING YOUR TABLE

To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING

PRODUCTS on your table's playing surface.

MAINTENANCE OF YOUR TABLE

Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.

This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood

to warp, swell, crack or blister.

UNLEVEL FLOORS

If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the

best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs.

Page 10

Replacement Parts List for Model Number T8780Q

Key# Part # Description Qty.

4A-5434-00

2S-6715-14

2S-6716-14

2S-6714-12

1B-4082-99

3M-6273-00

4A-7609-05

8S-6841-02

2Q-4017-00

2Q-4018-00

2B-4043-00

3M-6884-00

1B-6195-00

3M-6274-00

2W-6258-02

8S-6842-02

8S-6850-05

4A-5423-02

8S-6866-01

2S-4597-01

8S-6851-01

2S-6879-10

3B-4002-99

1B-4137-00

1A-6341-01

3M-6248-00

1B-6495-00

2B-4053-00

1B-4135-00

1B-4097-01

1B-6459-00

1N-0001-00

1B-4082-99

2B-4047-98

1B-4089-00

7B-4061-00

7B-6161-00

2B-6087-00

2B-4054-00

3M-6715-00

5A-6700-01

2L-4153-00

2S-6875-02

3B-6007-00

2B-4035-00

5/8" BLUE TOP ONLY SIDE RAIL - RIGHT HAND SIDE RAIL - LEFT HAND END RAIL #8 X 9/16 SHEET METAL SCREW U-SUPPORT CLIP (PLASTIC) CASTER BEAM ASSEMBLY CASTER BEAM ONLY 3" CASTER - NON LOCKING 3" CASTER - WITH LOCK 3/8" PUSH NUT STOP SPOOL 3/8-16 X 2 3/4 HEX HEAD BOLT TUBE PLUG - 1" X 2" BOTTOM BOARD LINKAGE STRUT TUBE HINGE & MOUNTING BRACKET ASSEMBLY LEG - BLUE MOUNTING BRACKET ONLY U SUPPORT 1" U-CLIP 1/8 X 1/8 PULL RIVET 1/4-20 x 2 1/2”HEX HEAD BOLT CROSS TUBE 2" SQUARE PLUG 3/8-16 X 3 1/2 HEX HEAD BOLT 3/8-16 NYLOC JAM NUT 1/4-20 X 2 3/4 HEX HEAD BOLT 1/4-20 X 1 1/2 PHILLIPS HEAD SCREW 1/4-20 X 3 1/4 CARRIAGE BOLT 1/4-20 WING NUT #8 X 9/16 SHEET METAL SCREW 1/4-20 NYLOC JAM NUT #8-32 X 1 1/4 SHEET METAL SCREW 3/4 OD X 13/32 ID X 3/4 LONG SPACER 1/2 OD X 9/32 ID X 3/8 LONG SPACER 1/4" PLASTIC WASHER 3/8" PLASTIC WASHER CORNER PROTECTOR 66" NET & POST SET (NOT SHOWN) OWNERS MANUAL - T8780Q SUPPORT PLATE RIVET 1/4” X 2 3/8” 1/4” PUSH NUT

2 2 2 2 124 8 2 2 2 2 4 8 8 4 1 4 4 4 4 4 2 6 4 8 2 4 4 12 4 4 4 4 4 16 4 4 4 8 8 4 1 1 4 4 4

2L-4153-00

3437

Stiga T8780Q Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual