Page 1
Be sure to write your model number and serial number here
for future reference. You can find these numbers printed on
the bottom of the table.
MODEL NO.: T8725W/F
DATE CODE : CPSIA#2-T8725W/F-_______-SY
PURCHASE DATE : _______________________
O W N E R ’ S M A N U A L
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
Leave bolts slightly loose until you are instructed to tighten them.
4. To make assembly as easy as possible, place all parts of the table tennis in a cleared area and
remove the packaging material. Organize all parts as per parts identifier in the assembly manual.
Do not dispose of the packing material until assembly is completed.
5. Avoid scratching table tennis top and metal tube parts during the assembly process.
6. Assemble product on clean, level and flat surface.
7. Take time to correctly orientate parts exactly as per each assembly diagram.
8. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS
CAUTION:
CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!
Thank you for buyi ng ou r product. We try hard to en sur e tha t our products are of h igh q ual ity and free of probl ems , suc h as
Manufacturin g def ect s or missing parts. Howe ver , if you have any probl ems w ith y our n ew product, pleas e DO NO T RET URN IT
TO THE STORE!
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone: 1-866-873-3528 Toll-Free!
Fax: 1-866-873-3533 Toll-Free!
E-mail: tabletennis@escaladesports.com
Please provide m ode l num ber and/or part num ber o f the p roduct and/or par t whe n you c all or write. These numb ers c an be found on the
product, packa gin g, an d/or in this Owner’ s Man ual .
Please visit our website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Mailing Address
(correspondence only):
Escalade Sports
PO Box 889, Evansville, IN 47706
R
Physical Location:
Escalade Sports
817 Maxwell Ave.
Evansville, IN 47711
Escalade Sport products may be manufactured and/or licensed under the following patents.
6120397 , 5816957 , 5769744 , 5119741 , 4911085 , 4717157 , D460140 , D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
R
C
2021 Escalade Sports
R
Page 2
CARE AND MAINTENANCE
You hav e purchased a qualit y product that will gi ve you years of enj oym ent. By followi ng these simple
maint ena nce steps, you wi ll add to the life of your n ew table.
TH E TAB LE TO P
The top (playing surface) of your tabl e is ma de o f Pa rti cle Board. Like all products mad e of wood, it
can b e affec ted by a tmospheric changes in both tempera ture an d humid ity. Th is may caus e a slight
sag or distortion a s the to p expa nds or c ontracts. This is normal and should no t caus e c oncern as it
does no t det ract from the pla y or utility value of th e table. After assem bly of the table, y ou can minimize
the e ffe cts of temp erature an d humidity changes by stor ing the table in a dry area when table is n ot
in use.
ST ORAGE OF YOUR TABL E
This ta ble must be stored ind oors to prevent dama ge to the playing s urface. Dampness a nd extreme
tempe rat ure changes can cause the wood to warp, swell, crack or blist er. When your table is not in
use, it should be stored i n a dry area . D ue to the nature of particle boar d, table t op may bo w.
Damp an d hum id conditions w ill amplify this. Th is is normal and will no t affect playability of table.
CL EANING Y OUR TABL E
To clea n you r table use a soft, d amp (NOT WET) cloth on ly. To prevent da mag e to your table’s p laying
surface, D O NOT USE ANY CHEMI CALS, AB RAS IVE OR CLEANING PR ODUCTS on your table ’s playing
surface.
MA INTENAN CE OF YOUR TABL E
Be sure t o oil all moving parts o f your table includi ng the pivot poin ts. This will insure t he safety and ease
of use of your t able.
This ta ble must be kept i ndoors to prevent d amage to the pl aying surf ace. Dampness and extreme
tempe rat ure changes whi ch occur on patios or si milar areas can c ause wood to warp, swe ll, crack or
blister.
UN LEVEL FL OORS
If tabl e doe s not seem level, i t is probably due to une ven or unlevel fl oor s. Set the table in i ts PLAYING
POSITION and move table sev eral inches in diffe rent directio ns to find the best loca tion for the table.
If the fl oor i s extremely unlev el, table may not play o r operate properly .
If table is high in the cent er, shim up un der the outer legs.
TRANSPORTING THE FOLDED TABLE TOPS
It is recommended to keep the carton for folded table storage and or transport.
Also, note when folded, the table has casters on the bottom side to make movement easier.
When transporting the folded half tops, be careful not to damage the lower corners or scratch the playing
surfaces.
- 2 -
Page 3
HARDWARE IDENTIFIER (To Scale)
H1
- 8 mm x 40 mm
Tensioning Knob Bolt - Short
(4 pcs)
PARTS IDENTIFIER (Not to Scale)
P1 - Table Tennis Table Top
and Frame Assembly
(2 pcs)
P2 - Leg With Leg Caps
Pre-installed
(4 pcs)
H2 - 8 mm x 55 mm
Knob Bolt - Long
(8 pcs)
P3 P4 - Lower “B”Leg
- Lower “A”Leg
Connector
(8 pcs)
Pre-installed
Connector
(8 pcs)
Pre-installed
P5 -
Upper Leg Connector
P6 - Net Post
(2 pcs)(4 pcs)
P7 - Net (1 pc)
- 3 -
Page 4
IMPORTANT NOTE: Place table half top with playing surface face down on a CLEAN flat surface
for ease of correct assembly and to prevent any sc
ratches or blemishes to the playing surface.
PARTS REQUIRED
P1
1 pc
Table Tennis Table Top and Frame Assembly
-
STEP 1:
Lay one piece P1 Table Tennis Table Top and Frame Assembly flat with playing surface
facing down as shown in FIGURE 1.
Unlock the SAFETY LOCK as shown in DETAIL A .
Carefully lift and fold open the table half.
P1
FIGURE 1
STEP 2:
Carefully Pull open the P2 Legs and slightly
push it down as shown in FIGURE 2.
DETAIL BDETAIL A
Safety Lock
P2
!
WARNING
Crush and Shear Points
Keep hands clear of hinge
area and Aprons when
unfolding table top.
push down
Pinch Points
Keep hands clear of
the leg pivot area when
folding the table leg.
FIGURE 2
!
Crush and Shear Points
Keep hands clear of hinge
area and Aprons when
unfolding table top.
Slightly
P2
Slightly
push down
s
WARNING
Pinch Points
Keep hands clear of
the leg pivot area when
folding the table leg.
- 4 -
Page 5
PARTS REQUIRED
4 pcs P5 Upper Leg Connector
-
8 pcs - H2 Knob Bolt - Long
STEP 3:
Install P5 Upper Leg Connector with P3 Lower “A”Leg Connector and P4 Lower “B”Leg Connector using H2 Knob Bolt - Long
as shown in FIGURE 3 & DETAIL B,C,D,E. Tighten this hardware. DO NOT OVERTIGHTEN AND CRUSH TUBES.
Repeat procedures for other table top.
H2
DETAIL BDETAIL B
P5
DETAIL BDETAIL C
P5
H2
NOTED:
Both P3 and P4 are pre-installed
FIGURE 3
P3
H2
P5
DETAIL BDETAIL D
P4
P3
P3
P5
P5
P4
P4
P3
P4
- 5 -
P4
H2
P5
P3
DETAIL BDETAIL E
Page 6
!
WARNING
THIS STEP REQUIRES TWO CAPABLE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT
ON ITS LEGS. BE CAREFUL THE TABLE IS HEAVY
DROPPING THE TABLE CAN CAUSE SERIOUS INJURIES
OR PROPERTY DAMAGES.
PARTS REQUIRED
2 pcs - P6 Net Post
2 pcs - P6 Net Post
1 pc
- P7 Net
1 pc
- P7 Net
4 pcs - H1
4 pcs - H1 Tensioning Knob Bolt – Short
STEP 4:
Attach one P6 Net Post to the middle edge of where the table halves meet.
Repeat this with other P6 Net Post on opposite side.
Then, slide P7 Net into corresponding P6 Net Post and repeat for the other side as shown in DETAIL F.
.
Install H1 Tensioning Knob Bolt - Short,
Snug Tighten these 4 pcs of H1 Tensioning Knob Bolt - Short.
Do not overtighten.
in one end of each P5 Upper Leg Connector as shown in DETAIL G.
P7
DETAIL BDETAIL F
P6
P6
P7
H1
P6
FIGURE 4
P5
H1
TOP VIEW
H1
P5
H1
NOTED:
Install and snug tighten H1
on other end of P5.
H1
P5
DETAIL BDETAIL G
Page 7
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
CAUTION:
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR
PROPERTY DAMAGE.
STORAGE OF THE TABLE:
STEP 1:
Remove the P7 Net and P6 Net Posts as shown in
FIGURE 5.
P7
P6
P6
FIGURE 5
STEP 2:
Remove H1 Tensioning Knob Bolt - Short, and H2
Knob Bolts - Long, as shown in FIGURE 6.
H1
H2
FIGURE 6
H2
H2
H1
H2
STEP 3:
Fold each Leg and half table as shown in FIGURE 7.
FIGURE 7
STEP 5:
Repeat procedure for other table top.
STEP 4:
Lock the table using SAFETY LOCK as shown in FIGURE 8.
FIGURE 8
- 7 -
Page 8
DETAIL A
C5
C7
C2
DETAIL B
C3
C8
DETAIL H
C10
C18
C17
DETAIL G
C12
C6
C15
C1
C19
C18
C10
C5
C13
P2
P1
P5
P3
C6
P4
C5
C8
DETAIL C
C14
C6
C10
C4
C5
C5
DETAIL D
C10
C11
DETAIL F
H2
C8
H1
DETAIL E
C9
C16
- 8 -
Page 9
T8725 TABLE TENNIS TABLE SPARE PARTS
Key# Part No.
H1 T8725SY-H1 8 mm x 40 mm Tensioning Knob Bolt - Short 4
H2 T8725SY-H2 gnoL - tloB bonK mm 55 x mm 8 8
P1 T8725SY-P1 ylbmessA emarF dna poT elbaT sinneT elbaT 2
P2 T8725SY-P2 )dellatsni-erP( spaC geL htiW geL 4
P3 T8725SY-P3 )dellatsni-erP( rotcennoC geL”A“ rewoL 8
P4 T8725SY-P4 Lower “B”Leg Connector (Pre-installed)
P5 T8725SY-P5 Upper Leg Connector
P6 T8725SY-P6 2
P7 T8725SY-P7 1
DETAIL A
C2 T8725SY-C2 8
C5 T8725SY-C5 16
C6 T8725SY-C6 8
C7 T8725SY-C7
DETAIL B
C3C5 T8725SY-C3 8 mm x
T8725SY-C5 8 mm x
C6 T8725SY-C6 8mm Nylon Lock Nut 8
C8 T8725SY-C8 8 mm x
Description
8
4
Net Post
Net
8 mm x
8 mm x
8 mm Nylon Lock Nut
8 mm x
75 mm Allen Head Bolt
22 mm Flat Washer
18 mm Plastic Bushing 8
50 tloB daeH nellA mm 8
22 mm Flat Washer 8
16 mm Plastic Step Bushing 16
Qty
DETAIL C
C4 T8725SY-C4 8 mm x 3
C5 T8725SY-C5 8 mm x
C6 T8725SY-C6 8mm Nylon Lock Nut 8
C10 T8725SY-C10 3.5 mm x 14 mm Round Head Screw 32
C14 T8725SY-C14 Plasitc Bracket 8
DETAIL D
C10 T8725SY-C10 wercS daeH dnuoR mm 41 x mm 5.3 16
11 T8725SY-C11 Plasitc Leg Cap 8
C
DETAIL E
C9 T8725SY-C9 3.5 mm x 12 mm Round Head Screw 8
C16 T8725SY-C16 Safety Lock 2
DETAIL F
H1 T8725SY-H1 8 mm x 40 mm Tensioning Knob Bolt - Short 4
H2 T8725SY-H2 8 mm x
C8
T8725SY-C8 8 mm x 16 mm Plastic Step Bushing 8
5 mm Allen Head Bolt 8
22 mm Flat Washer 16
55 mm Knob Bolt - Long 8
- 9 -
Page 10
T8485 TABLE TENNIS TABLE SPARE PARTS
Key# Part No.
DETAIL G
C1 T8725SY-C1 3.5 mm x 18 mm Flat Head Screw 48
C10 T8725SY-C10 3.5 mm x 14 mm Round Head Screw 16
C12 T8725SY-C12 Hinge 6
C13
DETAIL H
C
C
C19 T8725SY-C6 8
T8725SY-C13 Wheel 4
17 T8725SY-C17 6 mm x 55 mm Allen Head Bolt 8
18 T8725SY-C18 6 mm x 18 mm Plastic Flat Washer
Description
6 mm Nylon Lock Nut
3.5 mm x 14 mm Round Head ScrewC10 T8725SY-C10 32
Metal BracketC15 T8725SY-C15 8
16
Qty
- 10 -
Page 11
90 DAY LIMITED WARRANTY
This cons ume r warranty extends to t he original consumer p urchase of any ESCALADE S PORTS Product
R
(hereinafte r referred as the “Product”).
WA RRA NTY DUR ATION: This Product i s warranted to the origi nal consumer purchas e of a period of
ninet y (90 ) days from the origi nal purchase.
WA RRA NTY CO VERAG E: ESCALADE S PORTS warr ants to the o riginal Consume r Purchaser that any
R
Product o f its manufactur e is free from d efects in materia l and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRAN TY IS VOID IF THE PRODUCT H AS BEEN DAMA GED
BY ACCIDENT , UNREASONABLE USE, NE GLIGENCE, IMPROPE R SERVICE, FAIL URE T O FOLLOW INSTRUCTIO NS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT O F DE FECTS I N MATE RIAL AND
WORKMANSHIP .
WA RRA NTY PER FOR MANCE: D uring the above ninety ( 90) day warrant y period, ESCALADE SPOR TS shall
R
repai r o r replace with a compar abl e model, and Prod uct, or component thereo f, which m ay prov e
defective un der normal use an d proper c are , and which our examination sh all disclos e to our
satisfac tion to be thus defecti ve, please contact our Warr anty Dept.
1-866-873-3528 / W arranty Dept.
Escalad e S ports, Inc.-P.O. Box 889 , Evansville, IN 47706 - A ttn: Warranty Dept .
R
Or Writ e us at :
Or E-mail us a t:
customers erv ice@escaladesp orts. com
Other t han shipping requi rements no charge will be ma de for su ch repair or replaceme nt of in-warranty
Products. E SCALAD E S PORTS strongly recommends th at th e Product is insure d for value prior to mailing .
R
WA RRA NTY DISCLAIM ERS : ANY IMPLIED WARRANTIES AR ISING OUT OF THIS SALE, INCLUDING BUT NO T
LIMITED TO TH E I MPLIED WARRANT IES OF ME RCHANTABILITY AND FI TNESS FOR A PARTI CULAR PURPOSE,
ARE LIMITED IN D URATION TO THE ABOVE N INE TY (90) DAY WARRANTY PER IOD. ESCALADE SPOR TS SHALL
R
NOT BE LIABLE FOR LOSS OF USE OF THE PR ODUCT OR OTHER CONSEQ UENTIAL OR INCIDENTAL COSTS,
EXPENSES O R DAMAGES INCURRED BY THE CON SUMER OF ANY OTHER USE.
Some state s do not allow the exclusion or l imitation of implied warranties or cons equential or incidental
damages, so the above limit ati ons or exclusions m ay not apply to you.
LE GAL REMED IES : This warra nty give you specifi c legal rights an d you may also have other ri ghts which
may var y fro m state to state.
- 11 -
Loading...