1.Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2.Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3.Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting
holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.
4.Tools required for assembly: Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches.
Note: Adjustable wrenches can be substituted for wrenches.
Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone:Toll – Free !
1-866-873-3528
Fax:1-866-873-3533Toll – Free !
E-mail:tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTINGTECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTSFREQUENTLY ASKED QUESTIONS
®
ADDITIONAL ESCALADE
SPORTS PRODUCT INFORMATION
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2L-5040-00
ÓÓ
2010 Escalade Sports
ÒÒ
HARDWARE IDENTIFIER
27
28
3/8-16 Nyloc
Locknut
QTY. (4)
31
1/4-20 X 3 1/4 Carriage Bolt
35
#8-32 X 1 1/4
Sheet Metal Screw
QTY. (4)
3/8-16 x 3 1/2 Hex Head Bolt
QTY. (4)
QTY. (4)QTY. (4)
37
36
3/4” Long Spacer
QTY. (4)
3/8" Long Spacer
30
32
38
1/4"
Plastic
Washer
34
1/4-20 Nyloc Locknut
QTY. (12)
1/4-20 X 1 1/2 Phillips Truss
Head Screw
QTY. (4)
33
1/4-20
Wing Nut
#8 X 9/16
SMS
QTY. (4)
39
3/8"
Plastic
Washer
QTY. (8)QTY. (12)QTY. (4)
244423
1/4-20 X 2 1/2 Hex Head Bolt
QTY. (8)QTY. (4)
#10-24 Locknut
QTY. (4)
2
#10-24 X 1/2 Phillips Pan Head Screw
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
1. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#7) as shown in Figure 1. Turn
Caster Beams as shown and attach board with four
Carriage Bolts (#31) and four Wing Nuts (#32).
Tighten Thumb Screws securely.
Note: Support Plate (#43)
must be on inside of Caster
Rail (#7) as shown.
43
31
Figure 1
15
32
7
32
2. Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#7) as shown in Figure 2.
a) Loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster Beam (#7) as shown in the Top View and Figure 2.
b) Slide one Hex Bolt (#27) through Caster Beam (#7), one Plastic Washer (#39), Strut Tube (#17), Plastic Washer (#39), Support Plate (#43) Spacer (#36), Linkage (#16) and Locknut (#28) as shown in Figure 2 Top View.
c) Repeat on other end of Caster Beam (#7) and on second Caster Beam.
d) Tighten Bolts (#13) and Nuts (#28) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely.
Top View
31
7
16
Figure 2
Note: Strut tubes must
be turned as shown or
table will not operate
correctly.
17
7
27
39
17
36
28
16
7
13
43
39
28
36
27
16
17
12
13
3
Lay Table Top Assembly painted side down, on a smooth,
3.
flat surface. Use the shipping carton to protect the painted
surface of the table top. Attach legs (#19) to table top
with Hex Bolt (#24), two Plastic Washers (#38) and
Locknut (#34). Attach leg brace to Leg Mounting Bracket
(#25) with Phillips Head Screw (#23) and #10-24
Locknut (#44) as shown in Detail 1. Attach leg caps
(#26) to bottom of the legs (#19) as shown in Figure 3.
4. Rotate U-support (#21) that is on bottom of Table Top
Assembly until you see the screw holes in the slots of Uclips (#22). Slide U-support (#21) side to side if
necessary to see holes. See Figure 3.
Note: To aid in assembly you can use a cordless drill and
Phillips bit for Step 5 only. Wear safety glasses.
5. Insert Screw (#35) through slot in U-clip (#22) and into
U-support (#21). See Figure 3. Thread screw all the way
into U-support until it touches the back of the tube. There
should be about 3/8” of screw (#35) left sticking out.
Repeat for other screw as shown in Figure 3.
6. Repeat steps 3 through 5 on other table top assembly.
24
19
38
Leg Brace
44
23
Figure 3
19
26
34
25
Detail 1
35
35
21
Note: Slide U-Support back and forth
until you see the hole if necessary.
35
Table Top
21
Assembly
22
4
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, USUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
LEGS AND TRY TO ASSEMBLE. TABLE TOPS ARE
HEAVY - DO NO T ATTEMP T TO ASSEMBLE
ALONE!
7. Attach Table Top Assembly to Base Assembly (that you put together in steps 1 & 2), as shown in
Figure 4. Pivot Strut Tubes (#17) up as shown;
then, with at least one adult on each side of Table
Top, lift top and align ends of U-support tube
(#21) with tops of Strut Tubes (#17) on Caster
Beams (#7) as shown in Figure 4. Slide tubes
together.
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNA TTENDED. IT CO ULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
Table Top
Assembly
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes (#17).
21
U-Support
17
Strut Tube
PI
VO
T
STRUT
TUBES UP
Figure 4
17
7
7
5
8. Screw U-support tube (#21) to Strut Tubes (#17) with two Screws
(#33) as shown in Figure 5. Align holes in U-support with holes
in Strut Tubes and thread screw (#33) into hole in Strut Tube
(#17) Tighten screws all the way but be careful not to over
tighten. You could strip threads on screws if you over tighten.
Due to shipping requirements the hinge (#18) may be positioned as
Note:
shown in Detail A, you will have to rotate the hinge to the position shown
in Detail B. DO NOT unscrew the hinge, you can rotate the hinge
without unscrewing it from the table.
If you want to see a video on how to position hinge (#18) go to:
9. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 5
and Detail B. With hinge positioned as shown, align hole in hinge
with hole in Strut Tube and attach with ¼” Screw (#30), Plastic
Washer (#38) and Locknut (#34). Plastic Washer (#38) goes
between Strut Tube and Hinge. Tighten nut securely. Repeat for
other Hinge. CAUTION: Hinges must be positioned exactly
as shown or table will not operate correctly and could be
damaged.
10. Attach Linkages (#16) to Leg (#19) as shown in
Figure 5. Pivot one Linkage (#16) up and pivot
Leg out from top and align hole in Linkage with
hole in Leg (#19). Attach Linkage (#16) to Leg
(#19) using Hex Head Bolt (#24), Spacer (#37)
and Locknut (#34). Spacer (#37) goes between
Linkage and Leg. Attach other Linkage to Leg the
same way. Tighten nuts securely.
11. Attach Corner Protector (#40) to table corners.
Push snap tabs on Corner Protector into holes in
rails. Be sure that tabs are aligned with holes before pushing. You could break tabs if
they are not aligned correctly.
12. With at least two adults, repeat steps 7
through 11 for other table top assembly..
40
DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL
BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE KNOCKED OVER
CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.
Figure 5
37
Spacer (#37) goes
between Linkage (#16)
and Leg (#19)
24
17
16
18
34
34
16
19
33
30
30
34
21
19
16
38
37
18
34
ATTENTION: If hinge is positioned as
shown below (Detail A), Rotate the hinge
as shown in Detail B. Do not take the
hinge off the table.
18
24
33
Shipping position
of hinge
CAUTION: Position hinges exactly as
shown in Detail B or table will not
operate correctly and could be damaged.
Detail B
30
18
Assembly
position of hinge
In the correct position
Hinge #18 will look like a
“V” when attached to Strut
Tube (#17).
Detail A
17
34
38
17
17
Plastic Washer goes
38
between Strut Tube
(#17) and Hinge (#18)
6
OPENING AND CLOSING INSTRUCTIONS
CAUTION:
EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR
CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE
TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.
DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.
TO OPEN:
1. Hold center of top edge. Gently pull outward to midway position.
....
Continue to pull until disengaged from plastic clips and legs rest on the
....
floor as shown in Figure 6A and 6B. Do not leave table partially
....
opened at midway position.
2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 7.
4. Attach net posts and net to table as shown in Figure 8.
NOTE: Net will be tight. It will be necessary to stretch net. This will insure
proper net tension.
Plastic
Clip
Midway
Position
Figure 8
TO CLOSE:
1. Remove net and net posts from table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
plastic clips are engaged. Then continue
lifting until closed.
4. Raise other table half in the same manner.
as shown in Figure 9.....
Figure 6A
Figure 7
PLAYBACK POSITION
Push to lock hinge.
PLAYING POSITION
To lock hinge push up on
the table and push hinge
as shown in Figure 6B.
Hinge
Locked
Figure 6B
Figure 9
STORAGE POSITION
IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 10)
1. Set the table to the Playing Position and lock hinges as shown in
....
Figure 7.
2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create
....
enough slack to align table tops. See Figure 1.
3. With the help of two other adults, push the two table top halves so
....
they are in line with each other and re-tighten the Wing Nuts (#32) as
....
shown in Figure 10.
Figure 10
7
TOP VIEW
ONE YEAR LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original
purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from
defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR O THER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above one (1) year warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our
examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
1-866-873-3528 / W
arranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
customerservice@escaladesports.com
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE® SPORTS
strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE ONE (1) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR
OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board or MDF. Like all products made of wood, it can be affected by atmospheric changes in both temperature and
humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value
of the table. After assembly of the table, you can minimize the effects of temperature and humidity changes by storing the table in the folded up position in a dry area when table
is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to warp, swell, crack or blister.
When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may bow. Damp and humid conditions will amplify this. This is
normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING
PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or similar areas can cause wood
to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the
best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs.
8
3
2
20
4
1
25
40
44
34
38
24
23
19
22
21
24
34
37
34
38
18
30
26
17
35
35
6
5
16
36
39
11
12
10
8
13
27
Replacement Parts List for Model Number T8690
Key#Part #DescriptionQty.
4A-6603-03
1
2S-6715-14
2
2S-6716-14
3
2S-6714-00
4
1B-4082-99
5
3M-6273-00
6
4A-7609-03
7
8S-6841-05
8
2Q-4017-00
9
2Q-4018-00
10
2B-4043-00
11
3M-6884-00
12
1B-6195-00
13
3M-6274-00
14
2W-5045-02
15
8S-6842-02
16
8S-6850-07
17
4A-5423-02
18
1A-4107-00
19
2S-4597-01
20
8S-4157-02
21
2S-6879-10
22
TOP ONLY
SIDE RAIL - RIGHT HAND
SIDE RAIL - LEFT HAND
END RAIL
#8 X 9/16 SHEET METAL SCREW
U-SUPPORT CLIP (PLASTIC)
CASTER BEAM ASSEMBLY
CASTER BEAM ONLY
3" CASTER - NON LOCKING
3" CASTER - WITH LOCK
3/8" PUSH NUT
STOP SPOOL
3/8-16 X 2 3/4 HEX HEAD BOLT
TUBE PLUG - 1" X 2"
BOTTOM BOARD
LINKAGE
STRUT TUBE
HINGE & MOUNTING BRACKET ASSEMBLY
LEG ASSEMBLY
MOUNTING BRACKET ONLY
U SUPPORT
1" U-CLIP
2
2
2
2
140
4
2
2
2
2
4
8
8
4
1
4
4
4
4
8
2
6
15
31
7
28
14
16
32
43
28
9
2L-5040-00
Key#Part #DescriptionQty.
23
1B-4138-00
24
1B-4137-00
25
2S-6343-00
26
3M-4147-00
27
1B-6495-00
28
2B-4053-00
29
30
1B-4097-01
31
1B-6459-00
32
1N-0001-00
33
1B-4082-99
34
2B-4047-98
35
1B-4089-00
36
7B-4061-00
37
7B-6161-00
38
2B-6087-00
39
2B-4054-00
40
3M-6715-00
41
5A-6700-01
42
2L-5040-00
43
2S-6875-01
44
WB-1007-99
9
#10-24 X 1/2 PHILLIPS PAN HEAD SCREW
1/4-20 X 2 1/2 HEX HEAD BOLT
LEG MOUNTING BRACKET
1 3/4 LEG CAP
3/8-16 x 3 1/2 HEX HEAD BOLT
3/8-16 NYLOC JAM NUT
NOT USED
1/4-20 x 1 1/2 PHILLIPS HEAD SCREW
1/4-20 X 3 1/4 CARRIAGE BOLT
1/4-20 WING NUT
#8 X 9/16 SHEET METAL SCREW
1/4-20 NYLOC JAM NUT
#8-32 x 1 1/4 SHEET METAL SCREW
3/4 OD X 13/32 ID X 3/4 LONG SPACER
1/2 OD X 9/32 ID X 3/8 LONG SPACER
1/4" PLASTIC WASHER
3/8" PLASTIC WASHER
CORNER PROTECTOR
66" NET & POST SET (NOT SHOWN)
OWNERS MANUAL - T8690
SUPPORT PLATE
#10-24 LOCKNUT
4
8
4
4
4
12
4
4
4
4
12
4
4
4
12
8
4
1
1
4
4
MESA
NÚMERO DE MODELO
DE TENIS
T8690
MANUAL DEL USARIO
1.Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los
pasos antes de empezar cada paso.
2.Algunas partes pequeñas pueden ser empacadas dentro de las partes grandes . Verifique en el
interior de todas las partes y cartones antes de ensamblar o solicitar partes.
3.No ajuste las partes hasta que las instrucciones se lo indiquen. Si las partes se ajustan antes de lo
indicado, es posible que los orificios no queden alineados y las partes queden fuera de su lugar. Deje las tuercas
levemente flojas hasta que las instrucciones le indiquen ajustarlas.
4.Herramientas necesarias: ””Desarmador Phillips, dos llaves de 9/16 y dos llaves de 7/16 (Puede utilizar una
llave ajustable en vez de llaves).
Por favor no devuelva este producto a la tienda!
Contacte el departamento de servicio al cliente de Escalade® Sports:
Teléfono:1-866-873-3528¡Sin costo alguno!
Fax:1-866-873-3533¡Sin costo alguno!
Correo Electronico:tabletennis@escaladesports.com
Apartado postal (sólo para correspondencia):
Escalade Sports
PO Box 889
Evansville, IN 47706
Visite nuestra página Web internacional: www.escaladesports.com
SOLUCION DE PROBLEMAS POR INTERNET ASISTENCIA TÉCNICA
PEDIDO DE PARTES POR INTERNET PREGUNTAS FRECUENTES
MÁS INFORMACIÓN SOBRE PRODUCTOS DE ESCALADE® SPORTS
Los productos Escalade® Sports se pueden fabricar y/o producir bajo las siguientes patentes.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Puede haber patentes en trámite. Una o más patentes mencionadas y/o en trámite pueden cubrir productos específicos.
2L-5040-00
ÓÓ
2010 Escalade Sports
ÒÒ
IDENTIFICADOR DE TORNILLOS
27
3/8-16 x 3 1/2 Tornillo de Cabeza Hexagonal
28
3/8-16 Tuerca
de Seguridad
CANT. (4)
31
1/4-20 X 3 1/4 Tornillo de Carruaje
35
#8-32 X 1 1/4
Tornillo para lamina
de metal
CANT. (4)
CANT. (4)
CANT. (4)
36
Separador de 3/4”
37
Separador de 3/8”
30
32
38
1/4"
Rondana
de
Plastico
CANT. (12)CANT. (4)CANT. (4)
34
1/4-20 Tuerca de Seguridad
CANT. (12)
1/4-20 X 1 1/2 Tornillo Phillips
CANT. (4)
33
1/4-20
Tuerca de
Mariposa
CANT. (4)
#8 X 9/16
Tornillo SMS
CANT. (4)
39
3/8"
Rondana
de
Plastico
CANT. (8)
244423
1/4-20 X 2 1/2 Tornillo de Cabeza Hexagonal
CANT. (8)
#10-24 Tuerca de
Seguridad
CANT. (4)
2
2
#10-24 X 1/2 Tornillo Phillips
CANT. (4)
ADVERTENCIA!
LEA Y SIGA TODAS LAS INSTRUCCIONES DEL
ENSAMBLADO, LAS OPERACIONES Y LAS INSTRUCCIONES
DE SEGURIDAD. POR LO MENOS SE REQUIERE DE DOS (2)
ADULTOS PARA ENSAMBLAR LA MESA!
31
1. Una la Tabla Inferior (#15) a el Carril con Llantas (#7)
como esta mostrado en la Figura 1. Voltee los Carriles
como están ilustrados y una la Tabla Inferior con los
cuatro Tornillos de Carruaje (#31) y las cuatro Tuercas
de Mariposa (#32). Atornille las tuercas asegurándose
que estén apretadas y seguras.
Nota: La placa de Soporte
(#43) debe de estar en el lado
de adentro del carril con llantas
(#7) como está mostrado.
31
43
7
15
Figura 1
32
7
32
2. Una los Tubos Estructurales (#17) y los Tubos Conectores (#16) a los Carriles con Llantas (#7) como están mostrados en la Figura 2.
a) Afloje los Tornillos (#13) y las Tuercas (#28) para que el Tubo Estructural (#17) pueda caber entre la Placa de Soporte (#43) y Carril con Llantas (#7) como esta mostrado en la Vista de arriba y la Figura 2.
b) Deslice un Tornillo de Cabeza Hexagonal (#27) a través del Carril con Llantas (#7), seguida por una Rondana de Plástico (#39),
Tubo Estructural (#17), otra Rondana de Plástico (#39), Placa de Soporte (#43), un Separador (#36), Tubo Conector (#16), y Tuerca
de Seguridad (#28 ). Como están mostrados en la Vista de arriba y la Figura 2.
c) Repita en el otro lado del Carril (#7) y en el segundo Carril con Llantas.
d) Apriete los Tornillos (#13) y las Tuercas (#28) hasta que queden asegurados.
e) Apriete las Tuercas (#28) en los Tornillos (#27) hasta que queden asegurados.
Vista de arriba
16
28
36
43
Nota: Los Tubos Estructurales
deben de estar volteados como
está mostrado, si no la mesa no
operara correctamente.
39
17
12
16
Figura 2
7
17
17
39
28
36
7
27
3
13
16
27
13
3. Ponga la mesa del lado pintado boca abajo, en un lugar plano y
liso. Use el cartón donde vino la mesa para proteger el lado
pintado. Adjunte las patas (# 19) al tablero de la mesa con los
Tornillos Hexagonales (#24), dos Rondanas de Plástico (#38) y la
Tuerca de Seguridad (#34). Sujete la abrazadera de la pata al
soporte (#25) con los Tornillo Phillips (#23) y Tuerca de Seguridad
#10-24 (#44) como está mostrado en el Detalle 1. Inserte los
Tapones de las patas (#26) a las Patas (#19) como mostrado en la
Figura 3.
4. Gire el Tubo de Soporte-U (#21) hasta que se vean los hoyos a
través de las ranuras de las Abrazaderas-U (#22) donde iran los
tornillos. Descienda el Tubo de Soporte-U (# 21) de lado a lado
para ver los hoyos, si es necesario. Ver Figura 3.
Nota: Para facilitar el ensamblado se puede utilizar un taladro
inalámbrico y una broca Phillips únicamente para el paso 5. Use
anteojos de seguridad.
5. Inserte el Tornillo (#35) a través de las ranura de la abrazadera-U
(#22) y dentro del Tubo de Soporte-U (#21). Ver Figura 3.
Atornille al Tubo de Soporte-U hasta que toque el fondo del tubo. El
Tornillo (# 35) debe sobresalir aproximadamente 3/8”. Repita lo
mismo para el otro tornillo como se muestran en la Figura 3.
6. Repita los pasos 3-5 para ensamblar la otra mitad de la mesa.
26
24
19
38
Detalle 1
Abrazadera
44
34
23
25
Figura 3
19
35
35
21
35
Nota: Si es necesario deslice el
Soporte-U hacia delante y hacia
atrás hasta que vea el hoyo.
Tablero
21
Ensamblado
22
4
ADVERTENCIA!
POR LO MENOS SE REQUIEREN DOS (2) ADULTOS
PARA TERMINAR EL RESTO DEL ENSAMBLADO!
CUANDO ENSAMBLE LOS TABLEROS A LA BASE,
MUEVA EL TABLERO SOSTENIENDOLO ÚNICAMENTE
DE LA PARTE POSTERIOR, NO SE DETENGA DE LAS
PATAS DE METAL, DEL TUBO DE SOPORTE-U, DE LOS
TUBOS CONECTORES Ó DE LAS BISAGRAS. ESTAS
PARTES PUEDEN MOVERSE Y PODRÍAN LASTIMAR
LOS DEDOS O LAS MANOS, CAUSANDO LESIONES
GRAVES. POR FAVOR ENSAMBLE LA MESA COMO SE
MUESTRA, CON LAS PATAS COMPLETAMENTE
CERRADAS Y EL TABLERO EN POSICIÓN VERTICAL.
NO ABRA LAS PATAS Y TRATE DE ENSAMBLARLAS. LOS
TABLEROS ESTÁN MUY PESADOS-NO INTENTE
ENSAMBLAR (ARMAR) LA MESA SÓLO!
7. Una el Tablero Ensamblado a la base (que usted
ensamblo anteriormente siguiendo los pasos 1 y 2),
como está mostrado en la Figura 4. Mueva los Tubos
Estructurales (#17) hacia arriba como está mostrado;
después con por lo menos un adulto en cada lado de
la mesa, levante y alinee las orillas del Tubo de
Soporte-U (#21) insertelos en las puntas de los Tubos
Estructurales (#17) en los Carriles con Llantas (#7)
como están mostrados en la Figura 4. Deslice los
Tubos hasta que esten juntos.
ADVERTENCIA!
!
NO ABRA LA MESA EN LA POSICIÓN DE JUEGO,
HASTA QUE AMBAS MITADES DE LA MESA ESTÉN
INSTALADAS NO DEJE LA MESA LEVANTADA SOLA.
PODRÍA CAERSE SOBRE ALGUIEN CAUSANDO HERIDAS
SERIAS Ó DAÑO DE PROPIEDAD.
!
Tablero
Ensamblado
Por lo menos 2 adultos se
requieren para deslizar el
Tablero Ensamblado sobre
los Tubos Estructurales (#17).
17
21
17
GIRE
ESTRUCTURAL
TUBO
ARRI
BAHACIA
Figura 4
7
7
5
8. Atornille el Tubo del Soporte-U (#21) a los Tubos Estructurales
(#17) con los dos Tornillos (#33) como está mostrado en
Figura 5. Alinee los hoyos de los tubos de Soporte-U con los
Tubos Estructurales e inserte los Tornillos (#33) en los orificios de
los Tubos Estructurales (#17) Apriete los tornillos totalmente pero
tenga cuidado de que no queden sobre apretados ya que podría
barrer la cuerda de los tornillos si los sobre aprieta.
Nota: Debido a los requisitos de envío, la bisagra (# 18) puede venir
colocada como se muestra en Detalle A, usted tendrá que girar la
bisagra a la posición que se muestra en Detalle B. NO desatornille la
bisagra, usted puede girar la bisagra sin desatornillarla de la mesa.
Si desea ver un vídeo para ver la posición de bisagra (# 18) vaya a:
9. Una las Bisagras (#18) a los Tubos Estructurales (#17) como
están mostrados en la Figura 5 y Detalle B. Coloque la
bisagra en la misma posición como está mostrada; alinee el
hoyo de la bisagra con el hoyo del Tubo Estructural y únalo con
el Tornillo ¼” (#30), la Rondana de Plástico (#38) y la Tuerca de
Seguridad (#34). La Rondana de Plástico (#38) va entre el Tubo
Estructural y la Bisagra. Asegúrese que la tuerca esté apretada y
segura. Repita el mismo procedimiento para la otra bisagra.
ADVERTENCIA: Las bisagras deben ir exactamente en la
misma posición como están mostradas ó la mesa no
operará correctamente y puede ser dañada.
10. Una el Tubo Conector (#16) a la Pata (#19) como está
mostrado en la Figura 5. Gire el Tubo Conector (#16) hacia
arriba y gire la pata hacia abajo y alinee el hoyo en el Tubo
Conector con el hoyo en la Pata (#19). Una el Tubo Conector
(#16) a la Pata (#19) usando el Tornillo de Cabeza Hexagonal
(#24), el Separador (#37) y la Tuerca de Seguridad (#34). Los
Separadores (#37) van entre el Tubo Conector y la Pata. Una el
otro Tubo Conector a la Pata de la misma manera. Asegúrese
que las tuercas estén apretadas y seguras.
11. Adhiera los Protectores de la Esquina (#40) a las esquinas de la
mesa. Presionando con precisión las lengüetas dentro de los
hoyos de los protectores de las esquinas en los rieles. Esté
seguro que las lengüetas estén bien alineadas con los
hoyos antes de empujarlos. Ya que se podrían romper las
lengüetas si no están alineados correctamente.
12. Por lo menos dos adultos se requieren para repetir los
pasos 7 al 11 para el ensamblado de la otra mitad de la mesa.
ADVERTENCIA!
NO HABRÁ LA MESA EN LA POSICIÓN DE JUGAR HASTA
QUE AMBOS TABLEROS ESTÉN INSTALADOS! NO DEJE LA
MESA PARADA SIN ATENDER. SE PUEDE CAER Y PUEDE
CAUSAR HERIDAS GRAVES O DAÑOS MATERIALES.
ADVERTENCIA: Si la bisagra esta
40
colocada como esta mostrada en el
Detalle A, gire la bisagra como esta
mostrada en el Detalle B. No la
desatornille la bisagra de la mesa.
16
17
37
24
18
34
34
16
19
30
33
La Rondana de Plástico va
38
entre el Tubo Estructural
(#17) y la Bisagra (#18)
30
34
21
19
16
38
37
18
34
18
24
Bisagra en la
posición de envío.
PRECAUCIÓN: Las Bisagras deben de
ser colocadas exactamente como están
mostradas ó la mesa no trabajará
correctamente y puede ser dañada.
33
Detalle B
30
18
Bisagra en p
para Ensamblar.
En la posición correcta la
Bisagra #18 se verá como
una “V” cuando está
conectada al Tubo (#17).
Detalle A
17
34
38
17
osición
17
Figura 5
6
INSTRUCCIONES PARA ABRIR Y CERRAR
ADVERTENCIA!
PONGA ATENCIÓN AL ABRIR Y AL CERRAR LA MESA. MENORES DE EDAD QUE NO SABEN EL USO
APROPIADO DE LAS INSTRUCCIONES NO SE LES DEBE PERMITIR ABRIR Y CERRAR LA MESA. EL
MANEJO O USO INCORRECTO DE LA MESA PUEDE CAUSAR LESIONES GRAVES O DAÑOS
MATERIALES. NO DEBEN DE PARARSE, SUBIRSE O BRINCAR SOBRE LA MESA. LA HUMEDAD Y LA CONDENSACIÓN DAÑARÍAN LA SUPERFICIE DE LA MESA. LA MESA DEBE ESTAR EN EL INTERIOR
Y EN UN LUGAR SECO.
PARA ABRIR:
1. Sostenga la orilla de arriba. Suavemente jale hacia afuera hasta la posición media. Continúe
jalando hasta que se desenganche de el clip de plastico y las patas se apoyen sobre el piso. No
dejar la mesa parcialmente abierta en la posición media. Ver figura 6A y 6B.
2.Baje el segundo tablero como se describe en el paso 1.
3.Asegure las cuatro bisagras. Ver Figura 7.
4.Asegure los postes al centro de la mesa y deslize la red sobre ellos. Ver figura 8.
Figura 8
NOTA: La red debe estar tensa. Estirar bien. Esto asegurará la tensión correcta.
Posición a la
mitad
Bisagra en
posición
asegurada.
POSICION PARA JUGAR SOLO
Figura 6A
Figura 6B
Clip de
Plástico
PARA CERRAR:
1.Retire la red y los postes de la mesa.
2. Desenganche las cuatro bisagras.
3.Levantar una mitad del tablero al punto medio hasta que se
enganchen los clips de plástico. Continúe levantando hasta
cerrar.
4.Levante la otra mitad del tablero de la misma manera. Ver
figura 9.
Figura 9
POSICION PARA GUARDAR
Presione para
asegurar bisagra
Figura 7
SI LA MESA NO ESTA ALINEADA CORRECTAMENTEFigura 10
1. Ponga la mesa en posición para de juego y asegure las bisagras como se muestra en la
....
Figura 7.
2. Afloje las tuercas de mariposa (# 32) adjuntas a los tornillos (# 31) con el fin de crear
....
suficiente espacio para alinear las dos mitades de la mesa. Ver Figura 1.
3. Con la ayuda de otros dos adultos, empuje las dos mitades de la mesa hasta que estén
....
alineadas las dos mitades y volver a apretar las tuercas con alas (# 32) como se muestra en la
....
Figura 10.
POSICION DE JUEGO
: (ver )
VISTA DE ARRIBA
Figura 10
7
GARANTÍA LIMITADA POR UN AÑO
Esta garantía para consumidores de la compra original de cualquier producto ESCALADE SPORTS (en adelante denominado el
es aplicable
®
"Producto").
DURACIÓN DE LA GARANTÍA: Se garantiza este Producto al comprador original por un período de un (1) año a partir de la fecha de compra.
COBERTURA DE LA GARANTÍA: ESCALADE SPORTS le garantiza al comprador original que cualquier producto de su fabricación está libre de
defectos en los materiales y fabricación cuando se lo utiliza para el propósito establecido, bajo condiciones normales de uso. ESTA GARANTÍA
NO TIENE VALIDEZ SI EL PRODUCTO SE HA DETERIORADO POR ACCIDENTE, USO INDEBIDO, NEGLIGENCIA, MANTENIMIENTO
INCORRECTO, NO SEGUIR LAS INSTRUCCIONES QUE VIENEN CON EL PRODUCTO U OTRAS CAUSAS NO RELACIONADAS CON
DEFECTOS EN LOS MATERIALES O FABRICACIÓN.
APLICACIÓN DE LA GARANTÍA: Durante el período de garantía de un (1) año, ESCALADE SPORTS reparará o reemplazará con otro similar,
todo modelo o Producto o componente que resulte defectuoso bajo condiciones normales de uso y cuidado, cuando nuestra inspección
demuestre que a nuestra satisfacción el mismo realmente es defectuoso; sírvase contactar a nuestro Departamento de Garantía.
1-866-873-3528 / Departamento de Garantía (Warranty Dept.)
O escríbanos a:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
O por correo electrónico a:
tabletennis@escaladesports.com
Fuera de los gastos de envío, no se impondrá cargo alguno por la reparación o reemplazo de los productos en garantía. ESCALADE® SPORTS
recomienda asegurar los Productos por su valor antes del envío.
LIMITACIÓN DE LA GARANTÍA: TODA GARANTÍA ORIGINADA EN ESTA VENTA, INCLUYENDO EN FORMA NO TAXATIVA, LAS
GARANTÍAS IMPLÍCITAS DE COMERCIALIZACIÓN Y APTITUD PARA UN FIN ESPECÍFICO, TENDRÁ VIGENCIA POR UN PLAZO DE UN (1)
AÑO. ESCALADE® SPORTS NO SERÁ RESPONSABLE POR LA IMPOSIBILIDAD DE UTILIZAR EL PRODUCTO U OTROS COSTOS
INCIDENTALES O RELACIONADOS, PERJUICIOS O PERDIDAS GENERADAS POR EL CONSUMIDOR ANTE CUALQUIER OTRO USO.
Algunos estados no permiten la exclusión o limitación de las garantías implícitas o daños incidentales o conexos, de modo que las limitaciones
que anteceden pueden no ser aplicabes en su caso.
RECURSOS LEGALES: Esta garantía le otorga algunos derechos específicos además de otros derechos que varían según el estado.
CUIDADO Y MANTENIMIENTO
Ud. ha comprado un producto de calidad que podrá disfrutar muchos años. Si sigue estos simples pasos de mantenimiento, alargará la vida de la mesa.
TABLERO
El tablero (superficie de juego) está construido de aglomerado. Al igual que todos los productos de madera, se puede ver afectado por cambios de temperatura y humedad
causando una leve deformación por expansión o contracción. Esta situación es normal y no resta valor a la mesa ni afecta el juego. Después de armada, guardar plegada en
lugar seco cuando no está en uso para minimizar los efectos de cambios de temperatura y humedad.
GUARDADO DE LA MESA
Se debe guardar la mesa en el interior para prevenir daños en la superficie de juego. La humedad y los cambios buscos de temperatura pueden provocar alabeo, hinchazón,
fisuras o ampollado de la madera. Cuando la mesa no se encuentra en uso, guardar plegada en lugar seco. debido a la naturaleza del aglomerado, se puede alabear la
superficie. La humedad puede aumentar este efecto que es normal y no afecta el uso de la mesa.
LIMPIEZA
Para limpiar la mesa, utilizar un trapo suave y húmedo solamente (NO MOJADO). Para evitar daños en la superficie de juego, NO UTILIZAR AGENTES QUIMICOS,
ABRASIVOS NI PRODUCTOS DE LIMPIEZA sobre el tablero.
MANTENIMIENTO
Lubricar todas las partes movibles, incluyendo los puntos de giro. Esto garantizará la seguridad y facilidad de uso.
Guardar en lugar cerrado para impedir daños en la superficie de juego. La humedad y los cambios bruscos de temperatura que se producen en patios o áreas similares
pueden provocar el alabeo, hinchazón, fisuras o ampollado de la madera.
PISOS DESNIVELADOS
Si la mesa no parece estar nivelada, probablemente se deba a pisos desparejos o desnivelados. Colocar la mesa en POSICION DE JUEGO y moverla algunas pulgadas en
distintas direcciones hasta encontrar una mejor ubicación. Si el piso está extremadamente desnivelado, no se puede utilizar la mesa adecuadamente. Si el tablero está más
alto en el medio, suplementar con una cuña las patas exteriores.
8
3
2
20
4
1
25
40
44
34
38
24
23
19
22
21
24
34
37
34
38
18
30
26
17
35
35
6
5
# de Ref. # de Parte
1
4A-6603-03
2
2S-6715-14
3
2S-6716-14
4
2S-6714-00
5
1B-4082-99
6
3M-6273-00
7
4A-7609-03
8
8S-6841-05
9
2Q-4017-00
10
2Q-4018-00
11
2B-4043-00
12
3M-6884-00
13
1B-6195-00
14
3M-6274-00
15
2W-5045-02
16
8S-6842-02
17
8S-6850-07
18
4A-5423-02
19
1A-4107-00
20
2S-4597-01
21
8S-4157-02
22
2S-6879-10
16
36
39
11
10
8
13
27
Lista de partes reemplazables para el modelo T8690
CLIP DE PLASTICO
CARRIL DE LLANTAS (ENSAMBLADO)
CARRIL DE LLANTAS (SOLAMENTE)
LLANTA DE - SIN SEGURO
LLANTA DE 3"
3/8" CONTRATUERCA
CARRETE
3/8-16 X 2 3/4
TAPÓN - 1" X 2"
TABLA INFERIOR
TUBO CONECTOR
TUBO ESTRUCTURAL
BISAGRA (CON SOPORTE DE MONTAJE)
PATA ENSAMBLADA
SOPORTE DE MONTAJE (SOLAMENTE)
TUBO DE SOPORTE-U
ABRAZADERA-U DE 1”
#10-24 X 1/2 TORNILLO PHILLIPS
1/4 20 X 2 1/2 TORNILLO HEXAGONAL
SOPORTE DE PATA
TAPÓN DE 1 3/4”
3/8-16 x 3 1/2 TORNILLO HEXAGONAL
3/8-16 TUERCA DE SEGURIDAD
NO USADO
1/4-20 x 1 1/2 TORNILLO PHILLIPS
1/4-20 X 3 1/4 TORNILLO DE CARRUAJE
1/4-20 TUERCA DE MARIPOSA
#8 X 9/16 TORNILLO SMS
1/4-20 TUERCA DE SEGURIDAD
#8-32 x 1 1/4 TORNILLO PARA LAMINA DE METAL
SEPARADOR DE 3/4”
SEPARADOR DE 3/8”
1/4" RONDANA DE PLÁSTICO
3/8" RONDANA DE PLÁSTICO
PROTECTOR DE ESQUINAS
66" RED Y POSTES (NO ENSEÑADOS)
MANUAL DEL USUARIO - T8690
PLACA DE SOPORTE
#10-24 TUERCA DE SEGURIDAD
2L-5040-00
Cant.
4
8
4
4
4
12
4
4
4
4
12
4
4
4
12
8
4
1
1
4
4
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.