MODEL NO.
T8580
2018 Escalade Sports
2L-7650-00
A D V A N T A G E
T A B L E T E N N I S T A B L E
A S S E M B L Y I N S T R U C T I O N S
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll-Free!
Fax: 1-866-873-3533 Toll-Free!
E-mail: customerservice@escaladesports.com
Please Do Not Return This
Product to the Store!
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE
®
SPORTS PRODUCT INFORMATION
1-866-873-3528
2018 Escalade Sports
2L-7650-00
2
TWO WRENCHES REQUIRED FOR
ASSEMBLY (NOT INCLUDED)
P R E - A S S E M B L Y T I P S
P R E - A S S E M B L Y T I P S
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
Please Do Not Return This Product to the Store!
1/2”
(QTY. 1)
NET & POST SET
5A-4319-00
7B-4069-00
NYLON LOCKNUT
5/16-18”
2B-6009-03
5/16-18 X 1-3/4”
1B-4170-00
P A R T S N E E D E D
HEX HEAD BOLT
PLASTIC WASHER
5/16”
3
CASTER BEAM
CONECTOR CHANNEL
2S-4707-01
PRE-ASSEMBLED TABLE TOP
4A-5434-00
CASTER BEAM ASSEMBLY
4A-8250-00
(QTY. 4)
(QTY. 8)
(QTY. 2)
(QTY. 8)(QTY. 8)
(QTY. 8)
2
3
4
5
6
H A R D W A R E I D E N T I F I E R ( A C T U A L S I Z E )
A C C E S S O R I E S
1
DETAIL A
ASSEMBLY TIP
4
2. Press the tab on the Safety Latch (#30) to unlock the H leg (#19) and raise
the Front legs (#15) until they are in the vertical position. See DETAIL A.
Safety Latch
1
15
19
30
DO NOT pull up from legs (#19)
because you can damage the table.
These legs raise automatically when
Front Legs (#15) are raised.
1. Lay Table Top (#1) painted side down, on a smooth, flat surface.
CAUTION: Make sure that the table top is secure on the
sawhorses and NEVER leave the table top unattended.
Table top can be set on two saw horses. Although this will make
assembly easier it is not necessary to complete assembly. Always use
shipping container to protect the painted surface of the table top.
Raise the Front legs
(#15) until they are in
the vertical position
5
1
3. Push up to lock both hinges (#16 & #17) so that the front legs
remain in the vertical position. See DETAIL B.
DETAIL B
16
17
Hinge Locked
PUSH UP
6
4. Insert Bolt (#4) through the Plastic Washer (#5), Connector Channel
(#3), H legs (#19), another Connector Channel (#3), another Plastic
Washer (#5) and a Locknut (#6) but do not tighten the hardware yet.
See DETAIL C.
2
8
4
2
4
6
5
DETAIL C
7B-4069-00
PLASTIC WASHER
5/16”
(QTY. 8)
5
HEX HEAD BOLT
5/16-18 X 1-3/4”
1B-4170-00
(QTY. 8)
6
NYLON LOCKNUT
5/16-18”
2B-6009-03
(QTY. 8)
5
DETAIL D
3
3
4
5
6
5
3
3
19
Do not tighten
until the next step
19
5. Insert the Caster Beam Assembly (#2) between the Connector
Channels (#3) then secure the assembly using bolts (#4), Washers
(#5), and Locknuts (#6) as shown in DETAIL D. Tighten all
hardware at this time.
2
6. Repeat steps 1-5 to assemble a second table
half.
HARDWARE NEEDED (ACTUAL SIZE)
7
7. Turn table half (#1) over and set it on its legs carefully. Repeat step for second table half (#1).
THIS STEP REQUIRES TWO OR MORE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON
ITS LEGS. BE CAREFUL, THE TABLE HALVES ARE HEAVY.
If needed use the leg
levelers to level the table.
8. Attach Net posts to the middle of the table where the table halves meet. See Figure 1.
CAUTION
1
1
9. Slide the Net into both Posts making sure that the white cloth of the net is at the top. Use strings at either end of the Net
to tighten the net and attach to the base of net post securely.
NET POST
NET
NET
POST
FIGURE 1
Loading...