TABLE
TENNIS TABLE
MODEL NO.
T8562
O W N E R ’ S M A N U A L
1. Read this manual carefully before starting assemb ly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. Do not tighten hardware until instructed to do so. If hardware is tighten too soon, mounting holes
may not align and parts may not easily fit togeth er. Leave locknuts slightly loose until you are instructed to
tighten them.
4. Tools required for assembly: Phillips Screwdriver, Adjustable Wrenches, Rubber Hammer.
5. To make assembly as easy as possible, place all parts of the table in a cleared area and remove the packaging
material. Do not dispose of the packing material until assembly is completed. For he lp in identifying parts,
use the Parts List, Hardware Identification and the Exploded Drawings.
An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you
6.
could overtighten the hardware and strip the screws.
Save this instruction manual and your proof of purchase (receipt) in the event that the manufacturer has to
7.
be contacted for replacement parts.
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone: 1-866-873-3528 Toll-Free!
Fax: 1-866-873-3533 Toll-Free!
E-mail: tabletennis@escaladesports.com
Mailing Address(correspondence only):
Escalade Sports
PO box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMATION
R
QUESTIONS
2L-5056-00
Escalade Sport products may be manufactured and/or
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific
R
licensed
under the following patents.
product.
C
2014 Escalade Sports
R
THREE YEAR LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of three (3) years from the original
purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free
from defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS
VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO
FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL
AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above three (3) year warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and/or Product, or component thereof, for any product which may prove defective under normal use and proper care, and
which our examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
tabletennis@escaladesports.com
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE®
SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE THREE (3) YEAR WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT
OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY
OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to
state.
CAUTION
THIS IS A TABLE TENNIS TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP ON TABLE!
FAILURE TO COMPLY WITH THIS CAUTION COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMA GE!
UNLEVEL FLOORS
If table does not seem level, it is probably because flooris not level. Move table several inches (set table in
playing position) in different directions to find the best location for the table. If the floor is extremely
unlevel, table may not play or operate properly. If table is high in the center, adjust levelers on the outer legs.
CARE AND MAINTENANCE
You havepurchased a quality productthat will give youyears ofenjoyment. By following these simplemaintenance steps you will addto the life of your newtable.
The top(playingsurface) of your tableisofaluminumconstruction. Itcanbeaffectedby atmospheric conditions, meaning both temperature and humidity. This
may cause a slight sag or distortion as top expands or contracts. This is normal and should not cause concern as it does not detract from the play or utility value
of the table.
STORAGEOF YOUR TABLE
Windgusts can blow over or unexpectedlyopenthe table; Storein protectedarea. Whenyour table is not in use, it should be folded up in a dry area.
CLEANINGYOUR TABLE
To clean your tableuse a softdamp NOT WET cloth only. To prevent damage to your table'splaying surface DO NOT useany chemicals, abrasive,or cleaning
products onyour table's playing surface.
IMPORTANT: Periodically, lubricate all moving parts, including pivot points, to assure smooth opening and closing.A light lubricant such as WD-40is recommended.
2
1/4-20 X 3 1/4 Hex Head Bolt (4 pieces)
14
26
19
11
1/2 OD X .281 ID X 3/4 Long
Plastic Spacer (12 pieces)
24
3/4 OD X 1/4 ID Plastic Washer
(16 pieces)
#10-24 Locknut (4 pieces)
HARDWARE IDENTIFICATION
12
1/4-20 Nylon locknut
(16 pieces)
1/4-20 X 2 1/4 Phillips Pan Head Screw (4 pieces)
17
#10-24 X 2 1/2 Phillips Pan Head Screw (4 pieces)
#10-24 X 3/4 Thumb
Screw (4 pieces)
1/4-20 X 2 3/4 Carriage Bolt (4 pieces)
10
#8 X 5/8 Phillips Pan Head Screws (12 pieces)
15
27
M12 Hex nut (4 pieces)
20
1/4-20 X 2 3/4 Hex Head Bolt (4 pieces)
21
3
#10 Flat Washer (12 pieces)
37
1. Slide a Caster Wheel with Lock (#13) into Caster Beam
as shown in FIGURE 1. On the other end of the Caster
Beam attach a Caster Wheel without Lock (#9). Make
sure you have one Caster Wheel with lock and a Caster
Wheel without lock for each Caster Beam.
Repeat this step to attach the Casters to the second
Caster Beam.
READ AND FOLLOW ALL ASSEMBLY, OPERATING,
AND SAFETY INSTRUCTIONS CAREFULLY . AT LEAST
TWO (2) ADULTS ARE NEEDED TO PUT THIS TABLE
TOGETHER!
Parts Needed:
2 pcs - #8 Caster Beam
2 pcs - #9 Caster without lock
2 pcs - #13 Caster with lock
8
9
8
13
13
2. Attach Cross Tube (#7) to Caster Beam Assemblies (#8) using four Thumb Screws (#26) as shown
in FIGURE 2.
4
3. Attach four Strut Tubes (#4) and four Linkage Tubes
(#25) to Caster Beam Assembly using four Carriage
Bolts (#10), four Spacers (#11) and four Locknuts (#14)
as shown in FIGURE 3.
Snug, but do not overtighten the #14 Locknuts as
this is a pivot point.
NOTE: make sure
linkage and Strut tube
are turned as shown.
4
25
14
READ AND FOLLOW ALL ASSEMBLY, OPERATING,
AND SAFETY INSTRUCTIONS CAREFULLY. AT LEAST
TWO (2) ADULTS ARE NEEDED TO PUT THIS TABLE
TOGETHER!
Hardware Needed:
4 pcs - #10 Carriage Bolt
4 pcs - #11 Spacer
4 pcs - #14 Locknut
Parts Needed:
4 pcs - #4 Strut Tube
4 pcs - #25 Linkage Tube
10
NOTE: make sure
linkage tube is arched
in this direction.
11
Figure 3
NOTE: make sure
linkage tube is arched
in this direction.
5
4. A) Attach two Square Legs (#1) between Leg Mounting Brackets (#23) and Leg Mounting Bracket &
Brace Assemblies (#6) using two Hex Head Bolts (#21), four Plastic Flat Washers (#24)
and two Locknuts (#14) as shown in FIGURE 4 & DETAIL A.
Attach middle holes of two Square Legs (#1) to Leg Mounting Bracket & Brace Assemblies (#6)
using two Phillips Rd. Hd. Bolts (#17), two Flat Washers (#37) and two Locknuts (#19) as shown in
FIGURE 4 & DETAIL A.
B) Install one Hex Nut (#27) to each Leg Leveler
(#28). Then install Leg Levelers to Square Legs
as shown in FIGURE 4.
Repeat for other Table Top.
Hardware Needed:
2 pcs - #14 Locknut
2 pcs - #17 Phillips Rd. Hd. Bolt
2 pcs - #19 Locknut
2 pcs - #21 Hex Head Bolt
4 pcs - #24 Flat Plastic Washer
2 pcs - #27 Hex Nut
2 pcs - #37 Flat Washer
DETAIL
17
A
37
1
19
14
Parts Needed:
2 pcs - #1 Square Leg-Silver
1 pc - #2 Aluminum Top Assembly
2 pcs - #28 Leg Leveler
28
27
1
37
17
21
19
14
24
21
23
24
Do not use
bottom two holes.
NOTE:Hole is not on center and
must be assembled as shown with
offset hole toward middle of table.
6
6
23
Figure 4
Middle of table is
end without stripe.
6
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE T OPS
THEMSELVES. DO NOT GRASP METAL LEGS, USUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
LEGS AND TRY TO ASSEMBLE. TABLE TOPS ARE
HEAVY - DO NO T AT TEMPT TO A SSEMBLE
ALONE!
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STAN DING U NATTEN DED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
5. Attach table top to base assembly. Pivot Strut Tubes (#4)
up and then with at least one adult on each side of table
top, lift top and align ends of U-support Tube (#3) with
tops of strut tubes on caster beams as shown in
FIGURE 5. Slide tubes together.
Repeat for other Table Top.
3
Figure 5
NOTE: PIVOT STRUT TUBES
UP AS SHOWN.
4
7
6. A) Attach U-Support (#3) and Strut Tubes (#4) using two Phillips Rd. Hd. Screws (#15) as shown in FIGURE 6.
Note: If hinge (#5) is positioned as shown in DETAIL B, you will have to rotate the hinge to the position shown in Detail C.
DO NOT unscrew the hinge, you can rotate the hinge without unscrewing it from the table. If you want to see a video on how
to position Hinge (#5) go to: http://www.escaladesports.com/customer-service/videos.html
B) Attach Long Hinge & Mounting Bracket Assemblies (#5) to Strut Tubes (#4) using two Bolts (#12), two Spacers (#11), two Flat Plastic
Washers (#24) and two Locknuts (#14) as shown in FIGURE 6 & DETAIL C.
Tighten Nuts snug, but DO NOT OVERTIGHTEN, hinges must pivot. CAUTION: Hinges must be positioned exactly as shown or
table will not operate correctly and could be damaged. DO NOT take Hinges off.
C) Attach Linkage Tubes (#25) to Square Legs (#1) using two Hex Head Bolts (#20), two Flat Plastic Washers (#24), two Spacers
(#11) and two Locknuts (#14) as shown in FIGURE 6.
D) Attach two Corner Protectors (#29) to Top Assembly using four Screws (#15) with four Washers (#37) as shown in FIGURE 6.
Repeat for other Table Top.
Hardware Needed:
4 pcs - #11 Spacer
2 pcs - #12 Phillips Rd. Hd. Bolt
4 pcs - #24 Flat Plastic Washer
4 pcs - #14 LockNut
ATTENTION: If hinge is positioned as shown
below (DETAIL B), rotate the hinge as shown in
DETAIL C. Do not take hinge off.
6 pcs - #15 Phillips Rd. Hd. Screw
4 pcs - #37 Washer
2 pcs - #20 Hex head Bolt
5
4
DETAIL B
INCORRECT POSITION OF HINGE
CAUTION: Position hinges exactly as
shown in DETAIL C or table will not
operate correctly and could be damaged.
29
37
Part Needed:
2 pcs - #29 Corner Protector
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE INSTALLED!
DO NOT LEAVE TABLE STANDING
UN ATTENDED. IT COULD BE KNOCKED
OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
15
14
3
20
1
24
1
1
4
14
12
DET
24
AIL
C
5
CORRECT POSITION OF HINGE
In the correct position Hinge (#5) will look
like a “V” when attached to Strut Tube (#4).
25
15
4
1
1
14
24
11
Figure 6
12
5
NOTE: Tighten screws snug, but do not
overtighten, causing screws to strip in
metal tube.
8
Loading...