Stiga T8521 Owner's Manual

O W N E R ’ S M A N U A L

Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2L-4242-00

TABLE TENNIS TABLE

MODEL NO.

T8521

2015 Escalade Sports

Contact Escalade® Sports customer service department at: Phone: 1-866-873-3528 Toll-Free!

Fax: 1-866-873-3533 Toll-Free! E-mail: customerservice@escaladesports.com

Please Do Not Return This Product to the Store!

Contact Escalade® Sports customer service department at: Phone: Toll – Free ! Fax: 1-866-873-3533 Toll – Free ! E-mail: tabletennis@escaladesports.com Mailing Address (correspondence only): Escalade Sports PO Box 889 Evansville, IN 47706

1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering parts.

3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.

5. Tools required for assembly: Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches (Ratchet and 9/16”, 7/16” Sockets are recommended and can be substituted for wrenches).

6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten screws.

7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for replacement parts.

Please Do Not Return This Product To The Store!

Please visit our Website at:

www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE

SPORTS PRODUCT INFORMATION

P R E - A S S E M B L Y T I P S

2015 Escalade Sports

P R E - A S S E M B L Y T I P S

1-866-873-3528

1/4" Plastic Washer

Washer

Plastic

3/8"

1/4-20 X 3 1/4 Carriage Bolt

#8 X 9/16

SMS

#8-32 X 1 1/4

Sheet Metal Screw

3/8" Long Spacer

3/4" Long Spacer

1/4-20 X 2 3/4 Hex Head Bolt

HARDWARE IDENTIFIER

3/8-16

Locknut

1/4-20 X 1 1/2 Phillips Truss Head Screw

1/4-20

Locknut

3/8-16 x 3 1/2 Hex Head Bolt

(Qty. 4)

(Qty. 20)

(Qty. 4)

(Qty. 8)

(Qty. 4)

1/4-20 Wing Nut

Sorting your hardware ahead of time will speed up assembly time. Sort all your hardware now so it will be ready before you start assembly.

NOTE:

1. Attach Wood Bottom Board (#15) to Caster Beam Assemblies (#8)

as shown in Figure 1. Turn Caster Beams as shown and attach

board with four Carriage Bolts (#31) and four Wing Nuts (#32).

Tighten Wing Nuts securely.

(Qty. 4)

1/4-20 Wing Nut

Caster

with Lock

HARDWARE NEEDED

1/4-20 X 3 1/4 Carriage Bolt

(Qty. 4)

NOTE: Make sure logos are right side up and

facing the outside as shown.

Figure

Caster

with Lock

Note: Support Plate (#43) is on the inside of Caster Rail (#8) as shown.

READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2) ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!

CA UTION:

ASSEMBLY TIP

On the top of each page you will find a picture of the

Hardware Needed (to scale) along with the Quantity,

Key# and Description. You can lay the hardware on

the picture to identify and sort the hardware.

2. Attach Strut Tubes (#17) and White Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 2. a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster

Beam (#8) as shown in the Top View and Figure 2.

b) Slide one Hex Bolt (#27) through one linkage (#16) one Spacer (#36) pass through Caster Beam (#8), followed by one

Plastic Washer (#39), Strut Tube (#17), another Plastic Washer (#39), inner Support Plate (#43) and Lock Nut (#28).

c) Repeat on other end of Caster Beam (#8) and on second Caster Beam. d) Tighten Nuts (#28) on Bolts (#13) securely. e) Tighten Nuts (#28) on Bolts (#27) securely.

Note: Linkages & Strut

tubes must be turned as

shown or table will not

operate correctly.

(Inner Plate)

TOP VIEW

3/8-16

Locknut

(Qty. 4)

HARDWARE NEEDED

3/8-16 x 3 1/2 Hex Head Bolt

(Qty. 4)

36 39

3/4" Long Spacer

(Qty. 4)

3/8" Plastic

Washer (Qty. 8)

Figure

If you want to see a video on how to insert Screw (#35) go to:

http://www.escaladesports.com/customer-service/instruction-videos

Scan with your smartphone:

3. Rotate U-support (#21) that is on bottom of Table Top until you see the screw holes in the slots of U-clips (#22).

If necessary Slide U-support (#21) side to side and back and forth to see holes. See Figure 3 & Detail A.

4. Insert Screw (#35) through slot in U-clip (#22) and into U-support (#21). See Figure 3 & Detail A.

Thread screw all the way into U-support until it touches the back of the tube. There should be about 3/8” of screw (#35) left sticking out. Repeat for second Screw (#35) and U Clip (#22).

NOTE: To aid in assembly use a cordless drill but DO NOT over tighten screws. Wear safety glasses.

HARDWARE NEEDED

#8-32 X 1 1/4

Sheet Metal Screw

(Qty. 2)

Detail A

Note: This end has NO stripe.

Figure

NOTE: Prepare an area for the assembly of the second table top half. If necessary, move the first table top half aside with the aid of a helper. Be sure to place it in a location where it won't be disturbed or damaged. If setting on its side, be sure to place the bottom edge no less than 12 inches away from the wall. Also be sure to place carpet or pieces of the shipping carton down to protect table top edges. If floor is not carpeted, brace table top half with a heavy object to keep it from sliding.

5. Repeat step 3-4 to complete a second Table Top Assembly.

DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE

TABLE STANDI NG UNA TTENDED. IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.

6. Attach Table Top Assembly to Base Assembly as

shown in Figure 4. Pivot Strut Tubes (#17) up as

shown; then, with at least one adult on each

side of Table Top, lift top and align ends of U-

support tube (#21) with tops of Strut Tubes (#17)

as shown in Figure 4. Lower the table in a

controlled manner and as even as possible so the

Strut Tube goes in the U-Support evenly. Carefully

slide tubes together.

AT LEAST TWO (2) ADULTS ARE NEEDED TO COMPLETE THE REST OF THIS ASSEMBLY! WHEN ASSEMBLING TOPS TO BASE, HANDLE TOP ASSEMBLIES BY GRASPING ONLY THE TOPS THEMSELVES. DO NOT GRASP METAL LEGS, USUPPORT, LINKAGE, OR HINGES. THESE PARTS CAN MOVE AND COULD PINCH FINGERS OR HANDS CAUSING SERIOUS INJURY! ASSEMBLE AS SHOWN WITH LEGS FULLY CLOSED AND TOPS IN A VERTICAL POSITION. DO NOT OPEN

O ASSEMBLE. TABLE TOPS ARE

LEGS AND TR HEAVY -

HEAVY ALONE!

Y T

DO NOT ATTEMPT TO ASSEMBLE

Table Top Assembly

With at least 2 adults, slide Table Top Assembly onto Strut Tubes (#17).

Figure

U-Support

Strut Tube

PIVOT STRUT

TUBES UP

Strut Tube

HARDWARE NEEDED

DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE

1/4-20 X 1 1/2 Phillips Truss Head Screw

(Qty. 2)

Note: If hinge (#18) is positioned as shown in Detail B, you will have to rotate the hinge to the position shown in Detail C. DO NOT unscrew the hinge, you can rotate the hinge without unscrewing it from the table.

1/4-20 Locknut

(Qty. 2)

1/4" Plastic

Washer

(Qty. 2)

7. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 5 & Detail C. With

hinge positioned as shown, align hole in hinge with hole in Strut Tube and attach with ¼” Screw (#30), Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38) goes between Strut Tube and Hinge. Tighten nut securely. Repeat for other Hinge.

CAUTION: Hinges must be positioned exactly as shown or table will not operate correctly and could be damaged.

If you want to see a video on how to attach hinges to Strut tube go to:

http://www.escaladesports.com/customer-service/instruction-videos

Or Scan QR code with

your smartphone:

INSTALLED! DO NOT LEAVE TABLE STANDING UNATTENDED. IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.

ATTENTION: If hinge is positioned as

shown here (Detail B), Rotate the hinge as shown in Detail C. Do not take hinge off.

Elbow

Detail B

Incorrect position

of hinge with elbow

pointing up.

CAUTION: Position hinges exactly as shown in Detail C or table will not operate correctly and could be damaged.

Detail C

Elbow

Correct position

of hinge with elbow pointing down

In the correct position Hinge #18

will look like a “V” when attached

to Strut Tube (#17).

Hinge Assembly

with “elbow”

pointing down.

Figure

Hinge Assembly

with “elbow”

pointing down.

Plastic Washer goes between Strut Tube (#17) and Hinge (#18)

HARDWARE NEEDED

1/4-20 X 2 3/4 Hex Head Bolt

(Qty. 2)

1/4-20 Locknut

(Qty. 2)

37 5

8. Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#5) as shown in Figure 6. Align holes in U-support with holes in Strut Tubes and thread screw (#5) into hole in Strut Tube (#17). Tighten screws all the way but be careful not to over tighten as you could strip threads on screws.

9. Attach Linkages (#16) to Leg (#19) as shown in Figure 6. Pivot Leg (#19) out from the table top and pivot both linkages (#16) up and align hole in

Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg (#19) using Hex Head Bolt (#29), Spacer (#37) and Locknut (#34). Spacer (#37) goes between Linkage and Leg. Attach other Linkage to Leg the same way. Tighten nuts securely.

10. With at least two adults, repeat Steps 7-9

for other table top assembly.

#8 X 9/16

3/8" Long Spacer

(Qty. 2)

DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE STANDING UNATTENDED. IT COULD BE KNOCKED OVER CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.

Screw

(Qty. 2)

Note: Make sure

to install #5

Figure

screws

Spacer goes between Linkage Arm (#16) and Leg (#19)

Note: Make sure

to install #5

screws

+ 19 hidden pages

Stiga T8521 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual