Stiga PARK 100 B User Manual

STIGA PARK

100 B

8211-3014-08

1.

F

G

H

2.

3.

4.

2

GB

ENGLISH

SYMBOLS

The following symbols are displayed on the ma­chine in order to remind you about the safety pre­cautions and attention necessary when using the
machine.

The symbols mean:

Warning!
Read the instruction and safety manual be­fore using the machine.

Warning!
Do notput hands or feet underthe coverof
the machine when it is running.

Warning!
Beware of objects being flung out. Keep
spectators away.

Warning!
Beforestartinganyrepairwork,removethe
spark plug cable from the spark plug.

7b. Park 2000­Hook the tension roller spring H into the fastener,
just behind the front right wheel (fig 2).

8. Lift up the mower deck and hook the spring on
the implement lifting bar.

When changing the v-belt or removing the mower
deck, proceed in the reverse order.

ADJUSTING

1. Make surethat the tyres have thecorrect inflation
pressure:
Front: 0,6 bar (9 psi).
Rear: 0,4 bar (6 psi).

2. Stand the machine on a level floor. Slacken the
screws K and adjust the mower deck so that the
front and rear edges L come at the same distance
from the floor (fig 3). Tighten the screws.

Points 1 and 2 must be carried out toensure that the
mower deck mows evenly.

USE

ASSEMBLING

MOWER DECK

1.FittheattachmentsDonthefrontaxleprojections
by means of washers and locking clips (fig 1).

2. Fit the attaching arms of the mower deck on the
attachments on the machine.

3. Place on the v-belt betwe en the belt pulleyof the
mower deck and the centre belt pulley F of the ma­chine (fig 2).

4. The tensioning roller G should come on the left
side of the belt as viewed from the driving seat (fig

2)

5. Then pull the mower deck forwards so that the
holes in the attaching arms come in line with the
holes in the attachments on the machine.

6. Fit the bolts and tighten them.
7a. Park -1999:

Hook the tension roller spring H into the floor on
the right-hand side (fig 2).

MOWING HEIGHT

The mower deck has 5 fixed mowing heights,from
40 mm to 80 mm.

N.B. The stated mowing heights apply when the
machine is standing on firm ground.

MOWING HINTS

For the best effe ct follow this advice:

- mow regularly.

- use full throttle on the engine.

- keep the underside of the mower deck clean.

- use sharp blades.

- do not mow wet grass.

MAINTENANCE

Neitherthemotornorthemowerdeck
may be serviced unless:

- the motoris shut off.

- the ignition key is removed.

- the ignition cable is removed from the
spark plug.

- the parking brake is engaged.

- the mower deck is disengaged.

3

ENGLISH

GB

CLEANING

Each time after mowing wash off the underside of
the mower deck casing with a garden hose.

If grass has driedon, remove the mower deck and
scrape the underside clean.

If necessary, touch-up the underside with paint to
avoid rusting.

CHANGING DRIVE BELT BETWEEN
CENTRE BELT PULLEY AND MOW­ER DECK

1. Unhook the tension roller spring H (fig 2).

2. Unbolt the mower deck from the machine.

3. Push in the deck towards the machine.

4. Change the faulty v-belt. Always use a genuine
belt. The tensioning roller G should come on the
left side of the v-belt as viewed from the driving
seat (fig 2).

5. Bolt the mower deck on the attachments on the
machine.

6a. Park -1999:
Hook the tension roller spring H into the floor on
the right-hand side (fig 2).

6b. Park 2000­Hook the tension roller spring H into the fastener,
just behind the front right wheel (fig 2).

When the blades are due to be sharpened, the wet
grinding method with awaterstone orgrindstone is
to be used.

Following sharpening, the blades must
be balanced to avoid vibration damage.

CHANGING BLADES
Always use original spare parts when changing the
blades, blade attachments or bolts.

Always use original spare parts. Using
non-original spare parts can result in
the risk of damage even if they fit in the
machine.

When changing the blades, the blades central bolt
should also be replaced. It is provided with a lock­ing device. The blade bolts torque: 65 Nm.

SPARE PARTS

STIGA original spare parts and accessories are
constructed exclusively for STIGA machines.
Note that non original spare parts and accessories
have not been checked or approved by STIGA.

Usageof such parts and accessoriescan
influence the machines operability and
safety. S TIGA cannot be he ld responsi­ble for injuries c ause d by these prod­ucts.

CHANGING DRIVE BELT IN MOWER
DECK

1. Remove the mower deck from the machine.

2. Remove thetransmission casingover the mower
deck.

3. Releasethe springM whichholds thetensioning
roller (fig 4).

4. Change the v-belt and assemble in the reverse
order. Always use a genuine belt.

BLADES

Make sure the blades are always sharp. This gives
the best mowing results.

SHARPENING
For safety reasons the blades must not be sharp­ened on an emery wheel. Incorrect sharpening (=
high temperature) can result in the blades becom­ing brittle.

STIGA reserves the right to modify the product without
prior notice.

4

MOWING AHEAD

BOX 1006 · SE-573 28 TRANÅS

www.stiga.com