STIGA
TORNADO
51 S
PRO 51 S
8211-0225-10
SVENSKA
S
1
2
3
1.
3. LS 45
5. LS 45
FULL
ADD
FULL
ADD
3x
2.
FULL
0,15 l.
ADD
4. XTE
3x
6. XTE
STOP
H
I
7. 8.
S
SVENSKA
10. 9.
11.
13. XTE 14.
15. 16.
12. LS 45
0.7-0.8 mm
40 Nm
ENGLISH
GB
SYMBOLS
The following symbols are displayed on the
machine in order to remind you about the safety
precautions and attention necessary when using
the machine. The symbols mean:
Warning! Read the Instruction Book and
Safety Manual before using the machine.
Warning! Keep spectators away. Beware
of objects being flung out.
Warning! Do not put hands or feet under
the cover of the machine when it is
running.
Warning! Before starting any repair work,
remove the spark plug cable from the
spark plugs.
Warning! Always tilt the
lawnmower backwards when
cleaning the underside. Petrol and
oil can run out if the lawnmower is
tilted in the other direction.
ASSEMBLING
EJECTION SHIELD
Under no condition must the machine be
started without the ejection shield being
fitted on the machine. If it is not fitted,
stones and other flying objects may
easily be ejected by the rotating blade.
Fit the ejection shield in the holes on the chassis
with the help of two nuts. Tighten the nuts fully
(fig. 1).
HANDLEBAR
Move the upper part of the steering handle
upwards and tighten the locking knobs (fig. 2). The
height of the handle can be adjusted in three
different positions.
USING THE MOWER
BEFORE STARTING
FILL THE CRANKCASE WITH OIL
The lawn mower is delivered without any
oil in the motor crankcase. The
crankcase must, therefore, be filled with
oil before the motor is started the first
time.
Remove the oil dipstick (fig. 3,4). Fill the engine's
crankcase with 0.6 litres of good quality oil
(service class SE, SF or SG) Use SAE 30 or SAE
10W-30 oil.
Fill until the oil reaches the “FULL/MAX” mark
on the dip stick. Do not fill with too much oil.
CHECKING THE OIL LEVEL
Check before using the machine that the oil level is
between “FULL/MAX” and “ADD/MIN” on the
dipstick.
Remove and dry the dipstick (fig. 3,4). Slide it
down completely and tighten it. Unscrew and pull
it up again. Read-off. If the oil level is low, fill with
oil up to the “FULL/MAX” mark.
FILL UP THE PETROL TANK
Never remove the filler cap or fill with
petrol while the engine is running or still
warm.
Never completely fill the petrol tank.
Allow a little room for the petrol to
expand if necessary.
Some engines have an extra safety cover under the
regular fuel cap. This must not be reinstalled.
Preferably use environmentally friendly petrol, i.e.
alkylate petrol. This type of petrol has a
composition that is less harmful to people and
nature. It has e.g. no lead additives, no oxygenators
(alcohols and ethers), no alkenes and no benzene.
NOTE! If you change to
environmentally friendly petrol in an
engine previously run on ordinary leadfree petrol (95), the petrol
manufacturer’s recommendations must
be followed carefully.
Ordinary lead-free 95 octane petrol can also be
used. You must never use 2-stroke petrol mixed
with oil. NOTE! B ear in mind that lead-free petrol
is a perishable; do not purchase more petrol than
can be used within thirty days.
GB
ENGLISH
STARTING THE ENGINE
Keep hands and feet well away from the
rotating blade. Never put your hand or
foot under the blade casing or in the
grass evacuation unit while the motor is
running.
1. Place the lawn mower on flat, firm ground. Do
not start in high grass.
2. Make sure the spark plug lead is connected to
the spark plug.
3. When starting a cold engine: Press down the
primer fully 6 times (fig. 5,6).
When starting a warm engine the primer does
not need to be used. If the engine stops due toa
lack of petrol, refill and press down the primer
3 times.
4. Press in the Start/Stop-loop H against the
steering. Note that the Start/Stop loop H must
be kept pressed-in to prevent the engine from
stopping (fig. 7).
5 Grasp the starter handle and start the engine by
pulling briskly on the starter handle.
IN/ OUT COUPLING OF THE DRIVE
Engage the drive by pressing coupling clamp I
against the steering handle. Disengage the drive by
releasing coupling clamp I (fig. 7).
By pressing down the handlebar so that the driving
wheels release their grip on the ground, turning,
reversing, moving round trees etc. can be done
without having to disengage the drive system.
STOP OF ENGINE
The motor may be very warm
immediately after it is shut off. Do not
touch the silencer, cylinder or cooling
flanges as it can cause burns and injury.
1. Release Start/Stop-loop H to stop the engine
(fig. 7). This loop must not be disengaged (e.g.
through fixing it in the depressed position
against the steering), as the engine cannot be
stopped.
2. If the lawn mower is left unattended to, remove
the lead from the spark plug.
If the start/stop loop no longer works,
stop the engine by removing the lead
from the spark plug. Immediately take
the lawn mower to an authorised
workshop for repairs.
CUTTING HEIGHT
Shut off the motor before adjusting the
cutting height.
Do not set the cutting height so low that
the blade can hit uneven ground.
Avoid mowing when the grass is wet. The grass
then sticks to the underside of the casing, giving
poor mowing results.
The mower is fitted with a single lever control for
adjusting the cutting height. Pull the lever
outwards and adjust the cutting height on one of
the 8 positions to be most suitable for your lawn
(fig. 8).
MAINTENANCE
No service is to be made on the motor or
grass cutter unit without first switching
off the motor and removing the spark
plug cable from the spark plug.
Stop the motor and remove the spark
plug cable if the mower is to be lifted,
e.g. with transportation.
If the machine is to be tilted the fuel tank
must be emptied and the sparking plug
of the engine kept upwards.
CLEANING
After each time it is used the mower should be
cleaned. This is particularly important on the
underside of the mower casing. Wash out with the
garden hose. The mower will then last longer and
function better.
Note! High pressure washing units should not be
used. If grass has dried on to the cutterhead casing
it can be removed by scraping. If necessary, give
the underside a touch of paint to prevent rusting.
Clean the silencer and the surrounding
area regularly to remove grass, dirt and
flammable waste products.
Note that you should clean the area under the
timing gear casing once or twice a year. Set at the
lowest mowing height. Slacken the screws and
remove the timing gear casing (fig. 9). Clean with
a brush or compressed air.
The inside of the drive wheels should be cleaned
once a season. To clean a wheel, remove the hub
cap, screw, washer, and wheels. Brush or blow the
gear and the gear ring on the wheel to clean them
from grass and dirt (fig. 10). Remount the wheel.
ENGLISH
GB
COOLING SYSTEM
Before use, the engine's cooling system should be
cleaned. Clean the cylinder's cooling fins and the
air intake, removing any grass cuttings, dirt and the
like.
LUBRICATION
Set at the lowest mowing height. Slacken the
screws and remove the transmission casing (fig. 9).
Lubricate the driveshaft by the plastic bushings/
slide bearings I with oil or oil spray at least once a
season (fig. 11).
CHANGING OIL
Replace the oil when the engine is warm
and the fuel tank is empty. Take care
while draining as the oil is hot, this is to
prevent burns.
Change the oil the first time after 5 hours of
operation, and subsequently after every 50 hours
of operation or once a season. Remove the oil
dipstick and allow the oil to run out into a vessel.
Be careful not to let any oil run on to the grass.
Fill with new oil: use oil of SAE 30 or SAE 10W30 quality. The crankcase holds approx. 0.6 litre.
Fill until the oil reaches the “FULL/MAX” mark
on the dip stick.
AIR FILTER
A dirty and blocked air filter reduces the engine
output and increases engine wear.
Clean the filter every three months or after every
25 hours of use, which ever occurs first. More
often if the lawn mower is used on dusty ground.
Briggs & Stratton LS45: Carefully remove the air
cleaner so that no dirt falls down into the
carburettor (fig. 12). Take out the foam plastic
filter element and wash it in liquid detergent and
water. Dry the filter element. Pour a little oil on the
filter element and squeeze it in. Refit the air
cleaner.
Briggs & Stratton XTE 60: Loosen the screw and
fold down the cover of the air cleaner. Carefully
remove the filter cartridge (fig. 13). Knock it
against a flat surface. Replace the filter cartridge
with a new one if it is still dirty.
SPARKING PLUG
Never remove the spark plug or the
ignition lead when checking to see if
there is any spark, always use an
approved test instrument.
Clean the sparking plug regularly (every 100 hours
running). Use a wire brush for cleaning and adjust
the correct spark gap 0.7-0.8 mm (fig. 14).
Change the sparking plug if the electrodes are
excessively burnt or if the plug is damaged. The
recommendations of the engine manufacturers are
as follows:
Champion J19LM (RJ19LM) or another
equivalent spark plug ought to be used in Briggs &
Stratton engines.
ADJUSTMENT OF THE CLUTCH WIRE
If the drive cannot be engaged or disengaged, it
may be that the clutch wire needs adjusting.
Adjust as follows:
1. Remove the transmission cover by unscrewing
the screws S (fig. 9).
2. When the clutch loop is released it should be
possible to roll the mower without any
resistance. If this is not the case, loosen the
locking nut U and screw in the nipple T until the
mower can be moved backwards (fig. 15).
3. When the clutch loop is
pressed in approx. 2 cm
(position 1) there should be
some resistance when moving
the mower backwards. With
the clutch loop fully pressed
in (position 2) it should not be
possible to pull the mower
backwards. Loosen the
locking nut U and screw out
the nipple T until this position
is achieved.
4. Finally tighten the locking nut U.
GB
ENGLISH
CHANGING BLADES
Use protective gloves to prevent cuts
when changing blades.
Blunt and damaged blades tear off the grass and
spoil the look of the lawn after mowing.New, well
sharpened blades cut the grass cleanly, so that the
lawn looks green and fresh even after mowing.
Always check the blade after an impact. First
disconnect the ignition cable. If the blade system
has been damaged the defective parts must be
changed. Always use genuine spare parts.
To replace the blade, slacken the screw (fig. 16).
Fit the new blade so that the stamped STIGA
logotype is turned facing the blade attachment (and
not facing the grass). Refit as illustrated. Tighten
the screw fully to a torque of 40 Nm.
When replacing the blade, the blade screw should
also be replaced.
The guarantee does not cover damage to the blade,
blade holder or engine caused by running into
obstacles.
When replacing the blade, the blade holder and
blade screw, always use original spare parts. Nonauthentic spare parts could lead to the risk of
personal injury or damage, even if they fit the
machine.
SHARPENING OF THE BLADES
Sharpening of the blades must be done by wet
method grinding, using a whetstone or a
grindstone.
For the sake of safety, the blades should not be
sharpened on an emery wheel. A very high
temperature could cause the blade to become
brittle.
Once the blade has been sharpened, it
must then be balanced so as to avoid
vibration damage.
STORAGE
WINTER STORAGE
Empty the fuel tank. Start the engine and let it run
until it stops. The same petrol must not remain in
the tank for more than one month.
Tip up the mower and screw out the sparking plug.
Pour a teaspoon of engine oil in the sparking plug
hole. Pull out the starting handle slowly so that the
oil is distributed in the cylinder. Screw in the
sparking plug.
Thoroughly clean the mower and store it indoors in
a dry place.
SERVICING
Genuine spare parts are supplied by service
workshops and by many dealers.
www.stiga.com
EG-försäkran om överensstämmelse
EY-vaatimustenmukaisuusvakuutus
EU-overensstemmelseserklæring
EU-forsikring om overensstemmelse
EG-Konformitätsbescheinigung
1.Kategori
Luokka
Kategori
Kategori
Kategorie
Category
Catégorie
Categorie
Categoria
Categoría
Categoria
Kategoria
Категория
Kategorie
Kategória
Kategorija
2.Typ
Tyyppi
Typ e
Typ e
Typ
Typ e
3.Art.nr.
Tuotenumero
Art.nr.
Art.nr.
Art.-Nr.
Item no
4.Tillverkare
Valmistaja
Producent
Produsent
Hersteller
Manufacturer
5.Vibration
Tärinä
Vibration
Vibrasjon
Vibration
Vibration
Vibration
Vibratie
Vibrazioni
Vibración
Gräsklippare med bensinmotor
Bensiinimoottorikäyttöinen ruohonleikkuri
Plæneklipper med benzinmotor
Gressklipper med bensinmotor
Rasenmäher mit Benzinmotor
Lawnmowers with petrol engines
Tondeuses à moteur à explosion
Grasmaaiers met benzinemotor
Tosaerba con motori a benzina
Cortacéspedes con motor de gasolina
Máquinas de cortar relva com motores a gasolina
Kosiarki do trawy z silnikiem benzynowym
Газонокосилки с бензиновым двигателем
Sekačky trávy s benzinovým motorem
Benzinmotoros fűnyíró
Kosilnice z bencinskimi motorji
Typ e
Typ e
Tipo
Tipo
Tipo
Typ
N° d'article
Itemnr.
Articolo n.
Nº de
referencia
Item nº
Fabricant
Fabrikant
Produttore
Fabricante
Fabricante
Producent
Vibração
Wibrac je
Вибрация
Vibrace
Vibr áció
Tresljaji
(ISO 5349)
6A.Garanterad ljudeffektnivå
Taattu äänitehotaso
Garanteret lydeffektniveau
Garantert lydeffektnivå
Garantierter Geräuschpegel
Guaranteed sound power level
Niveau de puissance acoustique garanti
Gegarandeerd geluidsniveau
Livello di potenza sonora garantito
Nivel de potencia de sonido garantizado
Nível de ruído garantido
Nieprzekraczalny poziom hałasu
Гарантированный предельный уровень шума
Zaručená úroveň hluku
Garantált hangteljesítményszint
Zajamčena raven zvočne jakosti
6B.Uppmätt ljudeffektnivå
Mitattu äänitehotaso
Målt lydeffektniveau
Målt lydeffektnivå
Gemessener geräuschpegel
Measured sound power level
Niveau de puissance acoustique mesuré
Gemeten geluidsniveau
Livello di potenza sonora misurato
Nivel de potencia de sonido medido
Nível de potência sonora medido
Nieprzekraczalny poziom hałasu
Замеренный уровень шума
Naměřená úroveň hluku
Mért hangteljesítményszint
Izmerjena raven zvočne jakosti
EC conformity declaration
Déclaration de conformité CE
EU-gelijkvormigheidsverklaring
Dichiarazione di conformità CE
Declaración de conformidad CE
STOP
S511
1. 11-4281
3. 11-4286
GGP Sweden AB
P.O. Box 1006
SE-573 28 Tranås
Sweden
2
7.1 m/s
Тип
Typ
Típus
Tip
Pozycja nr
Арт. изд.
Císlo položky
Tételszám
Izdelek, št.
Изготовитель
Výrobce
Gyártó
Proizvajalec
99 dB(A)
(L
WA)
97 dB(A)
Declaração de conformidade da CE
Deklaracja zgodności EC
Декларация EC о соответствии
Deklarace shody s EU
EK megfelelőségi nyilatkozat
8.Fabrikat
Val mis te
Fabrikat
Fabrikat
Fabrikat
Make
9.Klippbredd
Leikkuuleveys
Klippebredde
Klippebredde
Schnittbreite
Cutting width
Largeur de coupe
Snijwijdte
Larghezza di taglio
10.Serienr
Valmistenumero
Serienr.
Serienr.
Seriennummer
Serial number
Numéro de série
Serienummer
Numero di serie
Número de serie
Número de série
Numer seryjny
Заводской номер
Číslo série
Sorozatszám
Serijska številka
11.Motor / Moottori / Motor / Motor / Motor / Engine / Moteur / Motor /
Motore / Motor / Motor / Silnik / Двигатель / Motor / Motor / Motor
(Σ)
Fabrikat
Val mis te
Fabrikat
Fabrikat
Fabrikat
Make
Modell
Malli
Model
Modell
Modell
Model
12.Rotationshastighet
Pyörimisnopeus
Rotationshastighed
Rotasjonshastighet
Umdrehungsgeschwindigkeit
Rotation speed
Vitesse de rotation
Rotatiesnelheid
Velocità di rotazione
Régimen
Velocidade de rotação
Prędkość obrotów
Частота вращения
Rychl ost otáčení
Rotációs sebesség
Hitrost vrtenja
7.Anmält organ
Ilmoitettu laitos
Bemyndiget organ
Underrettet organ
Anmeldeorganisation
Notified body
Organisme notifié
Keuringsinstantie
Organismo notificato
Organismo notificado
Organismo notificado
Urząd zatwierdzający
Уполномоченная организация
Oprávnený orgán
Az értesítés címzettje
Obveščeni organ
Marque
Fabricage
Marca
Marca
Marca
Marka
Marque
Fabricage
Marca
Marca
Marca
Marka
Modèle
Model
Modello
Modelo
Modelo
Model
Ancho de corte
Largura de corte
Szerokość koszenia
Рабочий захват
Šířka sekání
Vágási szélesség
Širina košnje
Izjava ES o skladnosti
Торговая марка
Značka
Gyártmány
Znamka
STIGA
51cm
Se dekal på chassit
Katso tarra rungossa
Se mærkat på chassis
Se etikett på chassiset
Siehe Schild am Chassis
See label on chassis
Voir la plaque sur le châssis
Zie label op chassis
Vedi etichetta sul telaio
Véase la etiqueta en el chasis
Ver etiqueta no chassis
Patrz etykieta na podwoziu
См. табличку на шасси
Viz štítek na podvozku
Lásd az alvázon lévő adattáblát!
Glej nalepko na šasiji
Марка
Značka
Gyártmány
Znamka
Модель
Model
Modell
Model
Briggs & Stratton
1. 10D902
2. 12H802
3000 rpm
ITS Testing &
Certification Ltd
Notified Body representative 0359
EG-försäkran om överensstämmelse
EY-vaatimustenmukaisuusvakuutus
EU-overensstemmelseserklæring
EU-forsikring om overensstemmelse
EG-Konformitätsbescheinigung
Denna produkt är i överensstämmelse med
- direktiv 89/336/EEG om elektromagnetisk kompatibilitet
- maskindirektiv 98/37/EEG med särskilda hänvisningar till direktivets bilaga 1
om väsentliga hälso- och säkerhetskrav i samband med tillverkning
- ljuddirektiv 2000/14/EG
Maskinen är utvecklad och tillverkad enligt följande standard:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Tämä tuote täyttää seuraavien direktiivien vaatimukset
- sähkömagneettista yhteensopivuutta koskeva direktiivi 89/336/ETY
- konedirektiivi 98/37/ETY viitaten erityisesti direktiivin liitteeseen 1, joka
käsittelee olennaisia terveys- ja turvallisuusvaatimuksia valmistuksen
yhteydessä
- meludirektiivi 2000/14/EG
Tuote on kehitetty ja valmistettu seuraavien normien mukaisesti:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Dette produkt er i overensstemmelse med
- direktiv 89/336/EØF om elektromagnetisk kompatibilitet
- direktiv 98/37/EØF om indbyrdes tilnærmelse af medlemsstaternes
lovgivning om maskiner med særlig henvisning til direktivets bilag 1 om
væsentlige sikkerheds- og sundhedskrav i forbindelse med konstruktion og
fremstilling
- direktiv 2000/14/EF om støjemission
Produktet er udviklet og fremstillet i overensstemmelse med følgende normer:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Dette produktet er i overensstemmelse med
- direktiv 89/336/EØF om elektromagnetisk kompatibilitet
- maskindirektiv 98/37/EØF med særskilte henvisninger til direktivets bilag 1
om vesentlige helse- og sikkerhetskrav i forbindelse med produksjon
- lyddirektiv 2000/14/EF
Produktet en utviklet og produsert i overensstemmelse med følgende normer:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Dieses Produkt ist in Übereinstimmung mit
- Direktive 89/336/EEG zur elektromagnetischen Kompatibilität
- Maschinendirektive 98/37/EEG mit besonderem Hinweis auf Anlage 1 der
Direktive über wichtige Gesundheits- und Sicherheitsanforderungen im
Zusammenhang mit der Herstellung
- Schallschutzdirektive 2000/14/EG
Das Erzeugnis ist in Übereinstimmung mit folgenden Normen entwickelt und
gefertig worden:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
This product conforms to
- Electromagnetic Compatibility Directive 89/336/EEC
- Machinery Directive 98/37/EEC with special reference to appendix 1 of the
directive regarding essential health and safety requirements in conjunction
with manufacturing
- Noise Emission Directive 2000/14/EC
This product has been developed and manufactured in conformance with the
following standards:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Ce produit est conforme à
- La Directive compatibilité électromagnétique 89/336/EEC
- La Directive machines 98/37/EEC, avec une référence particulière à
l'annexe 1 de la directive concernant les exigences essentielles en matière de
santé et de sécurité dans le cadre de la fabrication
- La Directive émissions de bruit 2000/14/EC
Le produit en question a été mis au point et fabriqué conformément aux
normes suivantes:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Dit product voldoet aan
- Richtlijn voor elektromagnetische compatibiliteit 89/336/EEC
- Richtlijn voor machines 98/37/EEC met speciale verwijzing naar aanhangsel
1van de richtlijn voor essentiële gezondheids-en veiligheidsvereisten i.v.m.
fabricage
- Richtlijn voor geluidsproductie 2000/14/EC
Het product is in overeenstemming met volgende normen ontwikkeld en
vervaardigd:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Questo prodotto è conforme alla
- Direttiva sulla compatibilità elettromagnetica 89/336/EEC
- Direttiva Macchine 98/37/EEC con particolare riferimento all'appendice 1
della direttiva riguardante i requisiti essenziali in materia di salute e sicurezza
relativi alla fabbricazione
- Direttiva sulle emissioni sonore 2000/14/EC
Riferimento alle norme armonizzate:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Utfärdat i Tranås
Annettu Tranåsissa
Udfærdiget i Tranås
Utstedt i Tranås
Ausgefertigt in Tranås,
Schweden
Issued in Tranås
Fait à Tranås
Gepubliceerd in Tranås
Rilasciata a Tranås
Emitido en Tranås
Publicado em Tranås
EC conformity declaration
Déclaration de conformité CE
EU-gelijkvormigheidsverklaring
Dichiarazione di conformità
Declaración de conformidad CE
Wydano w Tranås
Выдано в Трано се
Vydáno v Tranåsu
Kibocsátva Tranåsban
Izdano v Tranås
Declaração de conformidade da CE
Deklaracja zgodności EC
Декларация EC о соответствии
Deklarace shody s EU
EK megfelelőségi nyilatkozat
Este producto respeta las siguientes normas:
- Directiva 89/336/CEE sobre compatibilidad electromagnética
- Directiva 98/37/CEE sobre máquinas, especialmente su anexo 1 sobre los
requisitos esenciales de seguridad y de salud relativos a la fabricación de las
máquinas
- Directiva 2000/14/CE relativa a las emisiones sonoras
Referente a standards armonizados:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Este produto está em conformidade com
- Directiva sobre Compatibilidade Electromagnética 89/336/CEE
- Directiva relativa às Máquinas 98/37/CEE com referência especial ao
apêndice 1 da directiva referente aos requisitos essenciais de saúde e
segurança em conjunto com os de fabrico.
- Directiva sobre Emissão de Ruído 2000/14/CE
Referencias à normas harmonizadas:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Ten produkt odpowiada następującym normom:
- Kompatybilność elektromagnetyczna - dyrektywa 89/336/EEC
- Maszyny - dyrektywa 98/37/EEC, a szczególnie dodatkiem 1 dyrektywy,
dotyczącym podstawowych wymogów w zakresie zdrowia i
bezpieczeństwa w związku z produkcją.
-Emisja hałasu - dyrektywa 2000/14/EC
W odniesieniu do norm harmonizujących:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Tento výrobek vyhovuje
- Smernici o elektromagnetické kompatibilite 89/336/EEC
- Smernici o strojních zarízeních 98/37/EEC se speciálním odkazem na
prílohu 1 uvedené smernice týkající se duležitých požadavku na ochranu
zdraví a bezpecnost v souvislosti s výrobou
- Smernici o emisích hluku 2000/14/EC
Použité harmonizované normy:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Ta izdelek je v skladu z
- Direktivo 89/336/EGS o elektromagnetni zdru_ljivosti
- Direktivo 98/37/EGS o strojih, s posebnim sklicevanjem na njen Dodatek
1 v zvezi z osnovnimi zdravstvenimi in varnostnimi zahtevami, skupaj s
proizvodnjo
- Direktivo 2000/14/ES o emisijah hrupa
Hivatkozás a harmonizált szabványokra:
- EN 836, EN 292-2, EN 1033, EN ISO 3767, EN ISO 14982
Mats Antonsson
2003-11-14
Certifieringsansvarig
Sertifioinnista vastaava
Certificeringsansvarlig
Sertifiseringsansvarlig
Für die Zertifizierung
verantwortlich
Certification Manager
Directeur de Cer tification
Certification Manager
Direttore Certificazione
Responsable de
certificación
Izjava ES o skladnosti
Director de Certificação
Kierownik ds. legalizacji
Начальник службы
сертификации
Vedoucí pro certifikaci
A tanúsításért felelős igazgató
Poslovodja za izdajo
certifikatov
www.stiga.com
GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS
Loading...