STIEBEL ELTRON ULTRONIC 2 W User Manual [en, es, fr]
OPERATION AND INSTALLATION MANUAL
GUÍA DE OPERACIÓN E INSTALACIÓN
MODE D’EMPLOI ET MANUEL D’INSTALLATION
TOUCHLESS AUTOMATIC HIGH-SPEED HAND DRYERS
SECADORES DE MANO DE ALTA VELOCIDAD SIN CONTACTO
SÉCHOIRS DE MAIN SANS CONTACT AUTOMATIQUES ET ULTRA RAPIDES
»ULTRONIC™ 1 S
»ULTRONIC™ 1 W
»ULTRONIC™ 2 S
»ULTRONIC™ 2 W
STIEBEL ELTRON, Inc.
17 West Street | West Hatfi eld, MA 01088
Tel. 413-247-3380 | Fax 413-247-3369
Email info@stiebel-eltron-usa.com
www.stiebel-eltron-usa.com
Simply the Best
CONTENTS | OPERATION
OPERATION
1. Important instructions __________________________ 3
1.1 Symbol key _____________________________________________3
1.2 Symbols in this document
2. Safety precautions ______________________________ 4
3. Register your product ___________________________ 5
4. Instructions for the end user ___________________ 5
4.1 General use information ____________________________5
4.2 User servicing instructions __________________________5
INSTALLATION
5. Installation instructions for the licensed
installer __________________________________________ 6
6. Minimum clearances ____________________________ 6
7. Mounting the unit _______________________________ 7
7.1 Recommended mounting heights ____________ 7
7.2 Wall mounting ___________________________________ 7
_________________________3
8. Electrical connections ___________________________ 8
9. Dimensions _______________________________________ 9
10. Technical data ___________________________________ 9
11. Warranty ________________________________________ 10
12. Environment and recycling ____________________ 10
13. Wall-mounting template _______________________ 29
2 | ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS WWW.STIEBEL-ELTRON-USA.COM
GENERAL INFORMATION
m
th
t
t
IMPORTANT INSTRUCTIONS
1. Important Instructions
Read this entire manual. Failure to follow all the
guides, instructions and rules could cause personal
injury or property damage. Improper installation,
adjustment, alteration, service and use of this unit can
result in serious injury.
This unit must be installed by a licensed electrician and
plumber. The installation must comply with all national,
state and local electric codes. Proper installation is the
responsibility of the installer. Failure to comply with
the installation and operating instructions or improper
use voids the warranty.
Save these instructions for future reference.
Installer should leave these instructions with the
consumer.
If you have any questions regarding the installation,
use or operation of this hand dryer, or if you need
any additional installation manuals, please call our
technical service line at 800-582-8423 (USA and Canada
only). If you are calling from outside the USA or Canada,
please call USA 413-247-3380 and we will refer you to
a qualifi ed Stiebel Eltron service representative in your
area.
This is the safety alert symbol. It is used to alert
!
you to potential personal injury hazard. Obey
all safety messages that follow this symbol to avoid
possible injury or death.
1.1.2 Symbols
Symbol Description
Injury
Electrocution
Burns or scalding
Other situations
!
1.1.3 Keywords
KEYWORD
DANGER The keyword DANGER indicates
information that must be observed,
otherwise serious injury or death
will result.
WARNING The keyword WARNING indicates
information that must be observed,
otherwise serious injury or death
may result.
CAUTION The keyword CAUTION indicates
information that must be observed,
otherwise relatively serious or light
injuries may result.
1.2 Symbols in this document
ENGLISH
The chapter Operation is intended for homeowners,
heating contractors, plumbers and electricians.
The chapter Installation is intended for heating
contractors, plumbers and electricians only.
1.1 Symbol key
1.1.1 Layout of safety information
1
1 Symbol (see 1.1.2 "Symbols")
2 Keyword (see 1.1.3 "Keywords")
3 Designations (see 1.1.2 "Symbols")
4 Information text
WWW.STIEBEL-ELTRON-USA.COM ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS | 3
2
DANGER Electric shock
Before any work on the appliance,
disconnect all poles from the
power supply.
3
e
4
This symbol ( ) indicates that you must do
something. The necessary actions are indicated in a
step-by-step fashion.
General Information
This is the general information icon.
Please read and pay careful attention to all general
information notes.
GENERAL INFORMATION
SAFETY PRECAUTIONS
2. Safety precautions
Please read and follow these instructions.
!
Failure to follow these instructions could
result in serious bodily injury or death.
There are no user-servicable parts. Service of
the unit must be performed by qualifi ed service
technicians.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a) Use the unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch
power off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to
the service panel.
WARNING
!
To reduce the risk of fi re, or electric shock,
do not use this hand dryer with any solid state
speed control device.
DANGER Electrocution
Before proceeding with any installation,
adjustment, alteration, or service of this unit all
circuit breakers and disconnect switches servicing
the unit must be turned off. Failure to do so could
result in serious personal injury or death.
DANGER Electrocution: The unit must be
properly grounded. Failure to electrically
ground the product could result in serious personal
injury or death.
WARNING Injury
Where children or persons with limited
physical, sensory or mental capabilities are allowed
to control this appliance, ensure that this will only
happen under supervision or after appropriate instructions by a person responsible for their safety.
Children must be supervised to ensure that they
never play with the appliance.
WARNING Fire
Never operate this appliance ...
-if the minimum clearances to adjacent object surfaces are not maintained, for example to furniture,
net curtains, curtains, textiles or other fl ammable
materials (for minimum clearances, see specifi cation/dimensions chapter).
- in rooms where the appliance is at risk from fi re
or explosion as a result of chemicals, dust, gases or
vapors.
- in the direct proximity of pipes or containers that
carry or contain fl ammable or explosive materials.
- if work such as laying cables, grinding or sealing is
carried out in the installation room.
- if sprays, fl oor polish or similar products containing petroleum are used. Vent the room suffi ciently
before using unit.
- if an appliance component is damaged, the appliance has fallen over or already had a fault.
DANGER Electrocution
Never remove the unit's cover unless the
electricity servicing the unit is turned off. Failure
to do so could result in serious personal injury or
death.
4 | ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS WWW.STIEBEL-ELTRON-USA.COM
GENERAL INFORMATION
OPERATION
REGISTER YOUR PRODUCT
3. Register your product
You must register this product within 90
days of purchase on our website in order to
activate the standard warranty or to be eligible for
the extended warranty. Go to our web site at:
www.stiebel-eltron-usa.com and click on register
your product.
Before beginning the registration process, we
suggest that you gather the necessary information
which will be as follows:
Type, Example: Ultronic 1 S (from the black label that
is on the bottom of the unit)
Number listed after "Nr."
Place of Purchase
Purchase Date
First & Last Name
Email address
Physical Address
Phone Number
INSTRUCTIONS FOR THE END USER
4. Instructions for the end user
4.1 General use information
In order to dry your hands most effi ciently, please use
the following procedure:
Shake off excess water over the wash basin
Place hands underneath the unit at a distance of
4˝ - 7˝
Rub your hands together as if you were washing
them
Your hands will be dry in approximately 15 seconds.
The Stiebel Eltron Ultronic series hand dryers are
equipped with an infrared sensor switch. This sensor
will activate the unit when hands are placed underneath
it. Approximately 7 seconds after the hands have been
removed, the unit will automatically shut off.
The sensor is the black rectangle located underneath the
unit between the air exit and air inlet grills. The sensor
switch will not work properly if it has been covered by
gum or dirt. If the sensor is obstructed, the hand dryer
will switch off automatically to prevent it from running
continuously.
4.2 User servicing instructions
ENGLISH
IF YOU HAVE ANY QUESTIONS CONCERNING THE
REGISTRATION PROCESS OR WARRANTY OPTIONS,
PLEASE CONTACT STIEBEL ELTRON USA DIRECTLY AT
(800)-582-8423.
Limited liability warranty:
Stiebel Eltron, Inc. is not liable for damages to the unit,
damage to personal property, bodily injury, or loss of
life due to the following conditions:
- Non-observance of these instructions
-Incorrect use
- Installation of the appliance by unqualifi ed personnel
- Unauthorized modifi cations
-Technical modifi cations
- Use of unauthorized spare parts
The Ultronic hand dryer does not contain any
!
parts serviceable by the lay person. In case of
malfunction please contact a licensed electrician.
CAUTION Fire
Never spray cleaning spray into the air slot.
Ensure that no moisture can enter the appliance.
To clean the housing use a soft cloth with a mild
detergent if necessary. Never use any abrasive cleaners
since they will scratch the fi nish of the unit. Never spray
water or cleaning fl uids directly on hand dryer. While
cleaning the unit, make sure the electric eye switch is
not covered.
WWW.STIEBEL-ELTRON-USA.COM ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS | 5
INSTALLATION
INSTALLATION INSTRUCTIONS FOR THE LICENSED INSTALLER
5. Installation instructions for the
licensed installer
WARNING: TO REDUCE THE RISK OF FIRE,
!
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be
done by qualifi ed person(s) in accordance with all
applicable codes and standards, including fi re-rated
construction.
b) When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden utilities.
DANGER Electrocution
Before proceeding with any installation,
adjustment, alteration, or service of this unit all
circuit breakers and disconnect switches servicing
the unit must be turned off. Failure to do so could
result in serious personal injury or death.
6. Minimum clearances
WARNING Electrocution
Do not install unit where it can accidentally
be splashed with water. Observe all minimum
clearance requirements. Failure to do so could result
in serious personal injury or death.
Do not install the hand dryer in DANGER ZONES 0, 1,
or 2 (see upper right diagram). Doing so may allow
the unit to be splashed with water which could
result in serious personal injury or death.
24”
)
mm
(600
3
2
1
0
24”
(600
mm
)
mm
89”
(2250
118”
(3000
)
)
mm
WARNING Electrocution
Do not install unit where it can accidentally
be splashed with water, failure to do so could result
in serious personal injury or death.
All electrical work must comply with national
and applicable state and local electrical codes.
The circuit should be equipped with a “ground fault
interrupter” where required by local, state or national
electrical codes.
The Ultronic hand dryer must have its own independent circuit using cable of the appropriate size
protected by a correctly rated circuit breaker. The
Ultronic 1 S/W units are designed for 110-120 Volt
electrical service and require a 15 amp circuit breaker and a #14 gauge copper wire. The Ultronic 2 S/W
units are designed for 220-240 V or 208 V electrical
service and require a 15 amp circuit breaker and a
#14 gauge copper wire.
0 DANGER ZONE: do not install unit in bathtubs
showers, or wash basins.
1 DANGER ZONE: do not install directly above bathtubs
or showers.
2 DANGER ZONE: do not install within 24˝ of bathtubs
or showers
3 SAFE AREA: unit must be installed in this area,
outside of DANGER ZONES 2, 1 and 0.
´
(127 mm)
(40 mm)
1.6”
(130 mm)
(PP)
12”
5.1”
26_07_31_0167
Before mounting the unit to the wall, ensure
all minimum distances are met for safety and
performance considerations.
6 | ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS WWW.STIEBEL-ELTRON-USA.COM
D0000020798
INSTALLATION
MOUNTING THE UNIT
The unit must be installed at least 5˝ from
perpendicular walls.
The unit must be installed at least 12˝ above
countertops to avoid splashing the unit.
Ensure the air outlet is not obstructed
7. Mounting the unit
lone fü
rM
ont
a
ENGLISH
7.1 Recommended mounting heights
Age Age Height
Adult man 54˝ (1350 mm)
Adult woman 48˝ (1250 mm)
Preschool /
kindergarten
3 - 5 32˝ (810 mm)
26_07_32_0025
Rotate the 2 lock screws one turn clockwise until
they come to a full stop.
26_07_32_0047
Remove the housing by gently lifting upward from
the bottom. This will allow the hooks to disengage
from the attachment eyelets (see A, B, below). Once
the hooks have detached, pull the cover gently
forward to remove it.
Elementary
school
6 - 10 36˝ (910 mm)
Middle
school
10 - 13 44˝ (1120 mm)
High school 13 - 18 48˝ (1250 mm)
7.2 Wall mounting
Transfer the four mounting points to the wall
by using the enclosed drilling template and drill
mounting holes (see drawing, upper right).
2.
1.
A
B
A) Hooks B) Attachment eyelets
3.
26_07_32_004626_07_32_0041
WWW.STIEBEL-ELTRON-USA.COM ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS | 7
INSTALLATION
ELECTRICAL CONNECTIONS
8. Electrical connections
1 Wiring block
Install a 1/2˝ electrical connector in the back part of
housing in the hole located below the wiring block
(1, above).
Feed wires through connector; tighten clamp down
on wire.
The “live” wires must be connected to the slots
on the terminal marked N/L and L. The ground
wire must be connected to the slot on the terminal
marked with the ground symbol.
Put the housing back onto the front of the unit.
Lift upward to reengage the hooks into the
attachment eyelets.
Press the housing down gently so it locks in place.
2.
1
1.
3.
26_07_32_0042
Turn the two screws a full turn counterclockwise to
stop.
26_07_32_0045
26_07_32_0043
85_07_32_0002
8 | ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS WWW.STIEBEL-ELTRON-USA.COM
INSTALLATION
DIMENSIONS
9. Dimensions
10.2Ý (257 mm)
0.2Ý (3 mm)
0.16Ý (184 mm)
)
)
mm
6.34Ý (161
9.21Ý (234
)
mm
b01
11.38Ý (289
mm)
mm
3.86Ý (98
)
mm
3.2Ý (81
0.67Ý (17
mm)
7.56Ý (192 mm)
)
mm
(63
Ý
2.5
10. Technical data
Model No. Ultronic™ 1 S Ultronic™ 1 W Ultronic™ 2 S Ultronic™ 2 W
Item no. 231584 231585 231586 231587
Electrical Data
Phase single single single single
Voltage 120 V 120 V 208 V
Wattage 985 W 985 W
Amperage 8.5 A 8.5 A
775 W
3.85 A
240 V
1000 W
4.3 A
208 V
775 W
3.85 A
240 V
1000 W
4.3 A
ENGLISH
D0000020795
Minimum required
circuit breaker size
15 A
Min. required wire size #14 AWG copper
Dimensions
Height 11.4˝ / 289 mm
Width 10.1˝ / 257 mm
Depth 9.2˝ / 234 mm
Weight
Weight 9.7 lb. / 4.4 kg
Construction
Color Stainless steel Alpine white Stainless steel Alpine white
Housing aluminum
Degree of protection (IP) IP 23
Safety class system I
Other
Sound level 82 dB(A)
Air speed 210 mph / 94 m/s
Air volume 170.7 CFM / 190 m³/h
Drying time 15 seconds
WWW.STIEBEL-ELTRON-USA.COM ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS | 9
WARRANTY | ENVIRONMENT AND RECYCLING
11. Warranty
RESIDENTIAL & COMMERCIAL WARRANTY: STIEBEL ELTRON WARRANTS TO THE ORIGINAL OWNER THAT THE ULTRONIC SERIES
TOUCHLESS AUTOMATIC HAND DRYER WILL BE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS FOR A PERIOD OF THREE
(3) YEARS FROM THE DATE OF PURCHASE. SHOULD THE PART(S) PROVE TO BE DEFECTIVE UNDER NORMAL USE DURING THIS
PERIOD, STIEBEL ELTRON, INC. WILL BE RESPONSIBLE FOR REPLACEMENT OF THE DETECTIVE PART(S) ONLY. STIEBEL ELTRON,
INC. IS NOT RESPONSIBLE FOR LABOR CHARGES TO REMOVE AND/OR REPLACE THE DEFECTIVE PART(S), OR ANY INCIDENTIAL OR
CONSEQUENTIAL EXPENSES.
SHOULD THE OWNER WISH TO RETURN THE HAND DRYER FOR REPAIR, THE OWNER MUST FIRST SECURE WRITTEN AUTHORIZATION
FROM STIEBEL ELTRON, INC. THE OWNER SHALL BE REQUIRED TO SHOW PROOF OF PURCHASE DATE, AND TO PAY ALL TRANSPORTATION COSTS TO RETURN THE DEFECTIVE PART(S) OR HAND DRYER FOR REPAIR OR REPLACEMENT. WARRANTY IS VOID IF HAND
DRYER HAS BEEN INSTALLED OR USED IMPROPERLY OR IF DESIGN HAS BEEN ALTERED IN ANY WAY.
STIEBEL ELTRON, INC.
17 West Street
West Hatfi eld, MA 01088, USA
PHONE: 800-582-8423 or 413-247-3380
FAX: 413-247-3369
E-Mail info@stiebel-eltron-usa.com
www.stiebel-eltron-usa.com
12. Environment and recycling
Please help us protect the environment. Dispose of the
appliance and its packaging in accordance with national
regulations.
STIEBEL ELTRON, INC.
17 West Street
West Hatfi eld, MA 01088, USA
PHONE: 800-582-8423 or 413-247-3380
FAX: 413-247-3369
E-Mail info@stiebel-eltron-usa.com
www.stiebel-eltron-usa.com
10 | ULTRONIC™ 1 / ULTRONIC™ 2 TOUCHLESS AUTOMATIC HAND DRYERS WWW.STIEBEL-ELTRON-USA.COM
Loading...