STI 7535 User Manual

Protective Cabinet

STI-7534, STI-7535 and STI-7535AED

Features

• Clear, protective polycarbonate cover with siren/strobe alarm.

• Design allows visibility at any angle.

• Complete with mounting hardware and gasket.

• Includes wire shelf, backing plate and siren/strobe alarm — AED models

• External mounting tabs or internal drill dimples.

• Cover includes a coated steel internal mounting plate with a baked on white

enamel finish.

• Siren/strobe alarm lens is red. Also available with amber, green, blue or white lens.

• Siren offers 32 user selectable tones.

• Alarm can be set for a piercing 100 dB or 85 dB.

• Independent strobe and siren timing of 15 seconds, 30 seconds, 60 seconds or

continuous.

• Powered by a 9 VDC battery or external 12-30 volts.

• Low battery indicator.

We protect the things that protect you.

CONTENTS

Warnings ..................................................................................................page 2

Cleaning Instructions ..............................................................................page 2

Dimensions ..............................................................................................page 3

Specifications ..........................................................................................page 3

Installation of Cabinet ............................................................................page 4

Installation of Alarm ................................................................................page 4

Alarm Electronic Setup ............................................................................page 5

Alarm Tones ............................................................................................page 5

Alarm Timing and Volume ......................................................................page 5

Alarm Terminal Strip Connections ..........................................................page 6

Alarm Electronics Assembly ....................................................................page 6

Assembly Parts List ................................................................................page 7

Operation ................................................................................................page 7

Warranty ..................................................................................................page 7

Accessories & Replacement Parts............................................................page 8

WARNINGS

All units are recommended for indoor use. Unit must be tested periodically to
verify the life of battery. STI recommends you change the 9 Volt battery twice
a year. When purchasing a siren/strobe alarm, you will need to periodically
test the connections to make sure audibles function at a sound level to alert
staff. Installer may need to purchase a simple audio-meter, typically available
at your local electronics store, to measure the sound in areas where the alarm
is expected to be heard during normal noise environment. Results from this
test may prove it beneficial to purchase additional siren/strobe alarm units.

All specifications and information shown are current as of publication and
subject to change without notice.

CLEANING

1. Rinse cover with water to remove abrasive dust and dirt.

2. Wash with soap or mild detergent using a soft cloth. (DO NOT SCRUB.)

3. Rinse once more, then dry with a soft cloth or chamois.

4. To remove grease or wet paint, rub gently with a cloth wetted thoroughly
with naphtha, then wash and rinse. (DO NOT USE RAZOR BLADES.)

2

DIMENSIONS

1

4

.

2

in

.

(

3

6

0

m

m

)

1

2

.2

in.

(

3

1

0

mm)

BOTTOM VIEW

F

RONT VIEW

6.44 in.

(

164mm)

2

3

.

5

in

.

(

5

9

7

m

m

)

1

6

.

5

in

.

(

4

1

9

m

m

)

1

/4

”

D

I

A

M

E

T

ER

SPECIFICATIONS

OPERATING VOLTAGE Internal power 9 VDC battery (not included)

OPERATING TEMPERATURE 32°F -120°
POWER CONSUMPTION Stand by: 50µA

SIREN VOLUME Low: 85 dB

ALARM TIMING Independent control for siren and strobe:

LOW BATTERY WARNING LED flash once every 30 seconds

FORM C DRY CONTACTS 0-30VAC/DC, 1 Amp
RATED FOR Contacts reset after longest alarm setting

KEY SWITCH Alarm on: normally closed
ALARM SWITCH Stand by: normally open contact required
POLYCARBONATE UL94V-2

FLAMMABILITY RATING

Remote power 12-30 VDC

Siren low volume: 85mA
Siren high volume: 90mA
Strobe: 25mA

High: 100 dB

15s, 30s, 60s, continuous

3

DRILL

3-/16 DIA HOLES

19018 ANCHOR

#8-10

(2) PROVIDED

19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED

BASE PLATE

18074 SWITCH LOCK

SUB-SA505 KEY SWITCH
MOUNTING BRACKET

3 9/32 in.

18075 REPLACEMENT
#801 KEY

ENCLOSURE

ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN

WIRE ACCESS HOLE

ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN

M

19033 ANCHOR

(4) PROVIDED

04875 MOUNTING PLATE

PROVIDED

19002 SCREW
#8-32 x 3/8 in.
(4) PROVIDED

OPTIONAL SHELF
MOUNTING POSITION

0

7530WR
ADJUSTABLE SHELF
INCLUDED WITH
STI-7531AED ONLY

07530 CABINET
ASSEMBLY

6297530
GASKET PROVIDED

06298
M

OUNTING TABS (4) PROVIDED

19013 SCREW
#10 x 1 1/2 in.
(

4) PROVIDED

MOUNTING
TAB SLOTS

STI-7530 KEYLOCK

STI-7531 AND

STI-7531AED THUMBLOCK

INSTALLATION OF CABINET

Note: Installation of cabinet

should be before
installation of alarm
because the mounting
bracket butts up to
cabinet.

1. Insert the (4) 06298
mounting tabs fully into
backbox mounting tab
slots. Use rubber mallet if
necessary.

2. After selecting a suitable
location, place cabinet in
closed position, against the wall. Mark and drill (4) 1/4 in. diameter holes.
Insert the (4) 19033 anchors. Mount cabinet by driving in the four #10 x
1 1/2 in. screws.

3. For STI-7531AED select one of the two shelf mounting locations, install
shelf. Close and lock cabinet.

INSTALLATION OF ALARM

STEP 1 - MOUNTING OPTIONS

TO KEY MOUNT PLATE OR INTO WALL WITHOUT ELECTRICAL BOX

4

1

ALARM TIMING

VOLUME

STROBE TIMING

ON

OFF

1

2

3

4

5

0

S1

ALARM TONE

S

2

ALARM TIMING
S

TROBE TIMING

V

OLUME

LED QTY 10

LOW BATTERY

INDICATOR LED

TERMINAL STRIP

T

AMPER SWITCH

(REAR VIEW)

WIRE ENTRY

BATTERY

B

ATTE RY CABLE

SIREN

O

STEP 2 - ELECTRONIC SETUP -

O

SELECT ALARM TONE AND TIMING SEQUENCE

NOTE: Select-Alert must be on a flat surface and lens must be

installed or the tamper switch will trigger the alarm.

STEP 3 - ALARM TONES - S1

1 2 3 4 5

1 0 0 0 0 0 BUZZ

*

2 1 0 0 0 0 SLOW ON/OFF
3 0 1 0 0 0 SLOW SIREN
4 1 1 0 0 0 3 BEEP/PAUSE/REPEAT
5 0 0 1 0 0 UFO FAST
6 1 0 1 0 0 FAST SIREN
7 0 1 1 0 0 #5 FAST
8 1 1 1 0 0 #2 MEDIUM
9 0 0 0 1 0 #5 MEDIUM

10 1 0 0 1 0 SWOOP MEDIUM
11 0 1 0 1 0 #3 MEDIUM
12 1 1 0 1 0 BUZZ TONE
13 0 0 1 1 0 STEADY FAST
14 1 0 1 1 0 SWOOP SLOW
15 0 1 1 1 0 CONTINUOUS
16 1 1 1 1 0 FAST REPEAT

WIRES TO SIREN

1 2 3 4 5

17 0 0 0 01 STANDARD ALARM
18 1 0 0 0 1 #3 FAST
19 0 1 0 0 1 #5 SLOW
20 1 1 0 0 1 FAST BEEP
21 0 0 1 0 1 SOUND A
22 1 0 1 0 1 SOUND B
23 0 1 1 0 1 SOUND C
24 1 1 1 0 1 SOUND D
25 0 0 0 1 1 SOUND D LOUD
26 1 0 0 1 1 SOUND E
27 0 1 0 1 1 SOUND F
28 1 1 0 1 1 SOUND G
29 0 0 1 1 1 SOUND H
30 1 0 1 1 1 #4 LOW
31 0 1 1 1 1 SOUND K
32 1 1 1 1 1 CONTINUOUS FAST

NOTE: Sound may be disabled by clipping

wires to the siren. THIS WILL VOID ALL
WARRANTIES. Remove two screws on
circuit board; leave enough length of
wire to possibly reattach in the future.
Then insulate wires to prevent shorting
to electronic components.

STEP 4 - ALARM TIMING AND VOLUME - S2

ALARM

*

15 seconds 1111 High
30 seconds 1010 1
60 seconds 0101 Low
Continuous 00 00 0

TIMING

1 = ON 0 = OFF

*Factory default settings

5

1 2

STROBESIREN

3 4 5

VOLUME

05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE

1

9002 SCREW
#8-32 x 3/8 in.
(

4) PROVIDED

E

LECTRONICS

I

NSTALL ED

BASE PLATE

WIRE ACCESS HOLE

1

9016 TAMPER-PROOF

TOOL (1) PROVIDED

19011 TAMPER-PROOF
SCREW

ROUTE WIRES
THRU HOLE

REMOTE POWER IN

12-24 VDC, 125mA

(OPTIONAL)

+

-

OFF ON

MAIN POWER

CONTROL TO
KEY SWITCH

STAND

BY

REED

SWITCH FROM CABINET

FORM "C"

DRY CONTACTS

NORMALLY OPEN

COM

+

-

D

C

I

N

K

E

Y

S

W

I

T

C

H

A

L

A

R

M

S

WI

T

C

H

N

C

C

O

M

N

O

NORMALLY CLOSED

ACTIVE

STEP 5 - ELECTRONICS ASSEMBLY

Wiring: After mounting circuit board assembly, connect wires. Refer to terminal strip connections (step 6).

ens installation: Slide lip of lens behind circuit board mounting plate. Rotate lens into position. Secure with

L

amperproof screw and special wrench. Unit will not operate properly if lens cover is not installed.

t

!

STEP 6 - TERMINAL STRIP CONNECTIONS

6

NOTE: “DC IN” are the only

polarity sensitive
terminals. When
external power is
used, battery will
act as a backup.
“Dry Contacts: NC,
COM, NO” are used
for remote alarm
monitoring.

ASSEMBLY PARTS LIST
SIREN/STROBE ALARM

QTY. PART # DESCRIPTION

1 05000 Electronics assembly (includes base plate & electronics assembly)
1 05050-R Red lens (unless otherwise specified)
1 09723 Key switch mounting bracket
2 18075 #801 key
1 18074 Switch lock
1 18151 N.C. reed switch and magnet (installed in cabinet)
4 19002 Screw #8-32 x 3/8 in.
2 19039 Screw #6 x 1 1/4 in.
2 19018 Anchor #8-10
1 19011 #8-32 x 1/2 in. tamper screw
1 19016 Tamper wrench
1 BAT-9VDC 9 volt battery

CABINET

1 07530 Hinged polycarbonate enclosure
4 06298 Mounting tabs
4 19013 #10 x 1 1/2 in. screw
4 19033 Plastic anchor
1 07530WR Wire shelf (Included with AED models only)
1 04875 Mounting plate
4 19002 #8-32 x 3/8 in. screw
1 06297530 Gasket
1 07503 Thumb lock - STI-7535 models
1 18050 Key lock
2 18054 CH751 Key

}

STI-7534 models

STEP 7 - OPERATION

• Turn key switch on to arm.

• Cycle key switch to reset alarm.

• Alarm will sound when cabinet is opened (alarm switch is electronically
closed), alarm cover is removed or unit is removed from the wall.

• To service, turn key switch off.

WARRANTY INFORMATION

• Three year guarantee against breakage of polycarbonate in normal use

(one year on electro mechanical and electronic components).

• Electronic warranty form at www.sti-usa.com/wc14.

7

ACCESSORIES AND REPLACEMENT PARTS

AED-LBL AED label - 2 included (applied to sides of

cabinet; must be factory installed)

STI-SA5000-R Replacement Siren/Strobe Alarm
18054 Replacement key for cabinet lock on STI-7534
18075 Replacement key for Siren/Strobe Alarm
07530WR Wire shelf (included with AED models)

2306 Airport Road

Waterford, Michigan 48327-1209

Phone: [phone] • Toll Free: 800-888-4784 • Fax: [phone]

www.sti-usa.com

Safety Technology International (Europe) Ltd.

Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch

Worcestershire • B98 0HU • England • Tel: [phone]

Fax: [phone] • Freephone: 0800 085 1678 (UK only)

E-mail: [e-mail] • Web: www.sti-europe.com

Printed in USA SUBJECT TO CHANGE WITHOUT NOTICE Inst. Sht. STI-7535/STI-7535AED, JAN2014