STI 7511F-HTR User Manual

Safety Technology International, Inc.

2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
T

oll Free: 800-888-4784 • E-mail: [e-mail]

W

eb: www.sti-usa.com

Safety Technology International (Europe) Ltd.

U

nit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: [phone]
Fax: [phone] • Freephone: 0800 085 1678 (UK only)
E

-mail: [e-mail] • Web: www.sti-europe.com

IF CONDUIT HUB

IS NEEDED ORDER

SUB-6297B20

HUB KIT, GASKET

AND FASTENERS

NOTE:

SUB KIT IS

3/4 in. RIGID

DIE CAST

SUB-6297B20

3/4” NPT CONDUIT

HUB KIT (NOT

INCLUDED)

MOUNTING TABS & FASTENERS
19013 #10 x 1 1/2” PAN HEAD SCREW

07503 THUMB LOCK (SHOWN)
STI-7511F-HTR
18050 KEYLOCK STI-7510F-HTR

19033 PLASTIC ANCHOR

19013 #10 x 1-1/2 PAN

H

EAD SCREW (4) PROVIDED

0

6297T MOUNTING
T

AB (4) PROVIDED

19033 #10-12 PLASTIC
ANCHOR (4) PROVIDED

0

6297A-M BACK BOX

629721A FRAME GASKET

19002 #8-32 x 3/8”
PAN HEAD MACH SCREW
(4) PROVIDED

SUB-7500-HTR ASSEMBLY

19051 #8-32 x 3/8”
F

LAT HEAD SCREW

(4) PROVIDED

19083 M-F #8-32 x 3/8”
STANDOFF (4) PROVIDED

*

ADDITIONAL STANDOFFS MAY BE REQUIRED
WHEN USING A WATERTIGHT CONDUIT HUB.
19083 M-F #8-32 x 3/8”
1

9093 M-F #8-32 x 1-1/2”
1

9056 M-F #8-32 x 3”
(

NOT INCLUDED)

1

8021 3/4” NPT
WATERTIGHT CONDUIT
HUB (NOT INCLUDED)

0

7503 THUMB LOCK - STI-7511A-HTR

1

8050 KEY LOCK - STI-7510A-HTR

629723 COVER GASKET

DRILL (4) 1/4” DIAMETER

HOLES 1 1/4” DEEP

BACK BOX

HEAT
O

N

POWER

REMOVE

H

EAT

O

N

P

OWER

5.59 in.

(142mm)

7.53 in.(191mm)

4.04

1.88

INSTALLATION INSTRUCTIONS

1. Remove heater plate assembly (Illustration 1) from back box by
removing 4 flat head screws and set aside.

2. Mount back box and cover assembly in desired position. With
hinges horizontal or vertical, insert the (4) mounting tabs into
the back box slots (see Illustration 2). Mark and drill (4) 1/4”
diameter holes 1 1/4” deep. Insert plastic anchors and screw
back box to wall with (4) #10 x 1 1/2” screws.

3. Route wires for heater and appliance into back box through
conduit or small hole properly sealed.

ILLUSTRATION 1

ILLUSTRATION 2

Electronic warranty form at www.sti-usa.com/wc14

INSTALLATION OF HEATED POLYCARBONATE ENCLOSURE STI-7510A&F-HTR, STI-7511A&F-HTR

All specifications and information shown were current as of publication, and are subject to change without notice.

7510A-HTR IS JULY 2007

LOW TEMPERATURE

W

ARNING TERMOSTAT

C

LOSE @ 32°F

OPEN @ 50°F

ALUMINUM MOUNTING PLATE

TERMINAL BLOCK
(4 WIRE CONNECTION)

LED CONTROL

THERMOSTAT HOLDER

RESISTOR HEATER

OVER TEMP SAFETY

THERMOSTAT

OPEN @ 120°F

CLOSE @ 90°F

LOW
TEMP

POWER

THUMB LOCK

6

29723 HINGED COVER

629721A FRAME

06297F-M BACK BOX

SUB 7500-HTR ASSEMBLY 1/8 in.

CONTROL THERMOSTAT

CLOSED @ 50°F OPEN @ 70°F

S

TANDOFF MALE FEMALE

#

8-32 x 3/8”

19051 (4)

#8-32 x 3/8 FLAT

HEAD MS

“HEAT ON” RED LED

“POWER ON” GREEN LED

ADDITIONAL EYELET FOR SECONDARY LOCK

DEVICE WIRING ACCESS HOLE

ELECTRONIC DEVICE

MOUNTING HOLES

Safety Technology International, Inc.

2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Toll Free: 800-88 8-4784 • E-mai l: info @sti-us a.com
W

eb: www.sti-usa.com

Safety Technology International (Europe) Ltd.

U

nit 49G Pipers Road • Park Farm Industrial Estate • Redditch

W

orcestershire • B98 0HU • England • Tel: [phone]
Fax: [phone] • Freephone: 0800 085 1678 (UK only)
E-mail: [e-mail] • Web: www.sti-europe.com

4. Connect heater power and control wires. Note: Terminals are not

JUNE2008

ILLUSTRATION 3

polarity sensitive.

a. Connect low temperature monitor terminals to supervisory panel

if used (see Illustration 3).

b. Connect power terminals to power source. 12-24 volt AC/DC.

• Heating capacity is determined by input voltage. Be sure
the power source has enough capacity to support the load
at the input voltage.

12 Volt, 19 WATTS

16.5 Volt, 36 WATTS

24 Volt, 77 WATTS

• 16.5 VAC adapter included

ILLUSTRATION 4

5. Mount the heater plate assembly to the back box with
control thermostat toward bottom of enclosure (see
Illustration 4). Be sure to route wires for electronic device
through the hole in the center of the heater plate before
attaching heater plate. For vertical mounting (hinges to
right or left side) be sure control thermostat is towards
the bottom of the enclosure.

6. Connect the electronic device and mount to the heater
plate in mounting holes indicated using #6 - 32 x 1/2”
screws (2) provided.

NOTE: If moisture buildup occurs, drill a weep

hole on bottom side of back box.

7510A HTR INSTALL