STI 34150, 34100, 34151, 34101 Installation And Operation Manual

— 1 —

Installation and Operation Manual

STI Wireless Driveway Monitor

TM

Part of the Wireless Alert Series

Thank you for purchasing the STI Wireless Driveway Monitor. Your satisfaction is very important to us.
Please take the time to read this manual carefully to get the most from your new product.

How the products works:

Because of its patented magnetometer sensor transmitter system, the Driveway Monitor will only be
triggered by cars or trucks - not people, animals and so forth. When a vehicle passes the Motion Alert®
Sensor Transmitter next to the driveway, the receiver unit inside the office or home sounds a chime
and flashes the alert light. The earth has a uniform magnetic field around it. A vehicle creates a slight
disturbance in the earth’s field. The sensor transmitter detects this disturbance and transmits a signal
to the receiver.

Before you start:

Refer to this drawing to become familiar with all the parts.

BATTERY POWERED SENSOR

TRANSMITTER

SOLAR POWERED SENSOR

TRANSMITTER

Models: STI-34150 - Battery Power Kit
STI-34100 - Solar Power Kit

STI-34151 - Battery Powered Sensor
STI-34101 - Solar Power Sensor

SENSOR

TRANSMITTER

CAP

SENSOR

TRANSMITTER

BASE

MOUNTING

TUBE CAP

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

2 “C” BATTERIES
(NOT INCLUDED)

SENSOR TRANSMITTER

12” MOUNTING TUBE

MOUNTING STAKE

SENSOR

TRANSMITTER

BOTTOM

SENSOR

TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER
BOTTOM SCREWS

RECHARGEABLE
NiMH BATTERIES

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

12” MOUNTING TUBE

— 2 —

Install batteries into the sensor transmitter

1. Remove the sensor transmitter cap by turning it counterclockwise.

2. WITHOUT PULLING ON THE BRASS ANTENNA OR ANY WIRES, grasp the outside of
the battery/circuit board holder by the finger notches, twist gently and pull out. Insert
two “C” alkaline batteries (not included).

3. Replace the battery holder/sensor transmitter and sensor transmitter cap.

4. To test or program sensor transmitter, place the sensor transmitter on a table or
counter approximately 5-10 ft. away from the receiver.

Sensor transmitter can be

activated by rotating

and will make a faint clicking noise to verify operation.

5. Sensor should be programmed to receiver before mounting outdoors. Refer to
receiver instructions for programming. (Model STI-34150 is factory programmed for
your convenience.)

Battery Powered (STI-34150 & STI-34151):

FINGER

NOTCHES

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.

FINGER

NOTCHES

DRIVEWAY

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.

25' OR MORE

3' OR

LESS

12'

MAX

FINGER NOTCHES

DO NOT

PULL ANTENNA!

SENSITIVITY

ADJUSTMENT

Sensitivity Adjustment:

The factory default setting (HIGH) may be adjusted by changing the jumper position inside the
sensor transmitter.

1. Unscrew cap.

2. Position the jumper to desired sensitivity (as shown).

 •LOW:Positionjumperonthetwobottompegs.
 •MEDIUM:Completelyremovejumperorhangonmiddlepeg.
 •HIGH:Positionjumperonthetwotoppegs.

3. Replace cap.

FINGER

NOTCHES

DRIVEWAY

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.

25' OR MORE

3' OR

LESS

12'

MAX

FINGER NOTCHES

DO NOT

PULL ANTENNA!

SENSITIVITY

ADJUSTMENT

Low Sensitivity Setting:

•

•

•

Jumper Location

Medium Sensitivity Setting:

•

•

•

Jumper Location

High Sensitivity Setting:

•

•

•

Jumper Location

SENSOR TRANSMITTER BOTTOM
SCREWS

RECHARGEABLE NiMH BATTERIES

FINGER

NOTCHES

REMOVE PLASTIC TAB
FROM BATTERIES

DRIVEWAY

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM

STREET.

25' OR MORE

3' OR

LESS

12'

MAX

DO NOT

PULL ANTENNA!

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

Sensitivity Adjustment:

The factory default setting (HIGH) may be adjusted by changing the jumper position inside
the sensor transmitter.

1. Remove the bottom of the sensor transmitter by removing the 3 screws on the bottom
of the unit.

2. Position the jumper to desired sensitivity (as shown below).

 •LOW:Positionjumperonthetwoleftmostpegs.
 •MEDIUM:Completelyremovejumperorhangfrommiddlepeg.
 •HIGH:Positionjumperonthetworightmostpegs.

3. Replace the bottom of the unit and secure with the 3 screws.

Solar Powered (STI-34100 & STI-34101):

1. Remove the bottom of the sensor transmitter by removing the 3 screws on the
bottom of the unit.

2. Remove the plastic tab between the batteries.

3. Replace the bottom of the unit and secure with the 3 screws. Place the sensor
transmitter in direct sunlight for 48 hours.

OR

4. Place batteries in a NiMH (nickel metal hydride) battery charger (before using). Once
charged, return the batteries to the sensor transmitter. Replace the bottom and secure with the 3 screws.

5. To test or program sensor transmitter, place the sensor transmitter on a table or counter approximately 5-10 ft. away from
the receiver. Sensor transmitter can be activated by rotating and will make a faint clicking noise to verify operation.

6. Sensor should be programmed to receiver before mounting outdoors. Refer to receiver instructions for programming. (Model
STI-34100 is factory programmed for your convenience.)

Low Sensitivity Setting:

•

•

•

Jumper Location

Medium Sensitivity Setting:

Jumper Location

High Sensitivity Setting:

Jumper Location

•

•

•

•

•

•

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

2 “C” BATTERIES
(NOT INCLUDED)

SENSOR TRANSMITTER

SENSOR

TRANSMITTER

BOTTOM

SENSOR

TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER
BOTTOM SCREWS

RECHARGEABLE
NiMH BATTERIES

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

+

+

-

B

-

SENSITIVITY

ADJUSTMENT

12” MOUNTING TUBE

Installation Instructions:

The Solar Sensor Transmitter must be placed in an area that receives partial or full sunlight. For both models, be sure the
location of the sensor transmitter is at least 25’ back from the main road. For a typical 12’ wide driveway, it is recommended
the sensor transmitter be no more than 3’ away from the driveway (see drawing). Additional sensor transmitters may be required
for driveways exceeding 12’. Sensor transmitter may be placed up to 1,000 feet away from receiver; however, range may vary
depending upon environment and use of wireless telephones, wireless routers and other similar devices.

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

2 “C” BATTERIES
(NOT INCLUDED)

SENSOR TRANSMITTER

SENSOR TRANSMITTER

BOTTOM

SENSOR TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER BOTTOM
SCREWS

RECHARGEABLE NiMH BATTERIES

REMOVE PLASTIC TAB
FROM BATTERIES

DRIVEWAY

3’OR
LESS

25' OR MORE

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.

12’

MAX

DRIVEWAY

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.

25' OR MORE

3' OR

LESS

12'

MAX

FINGER NOTCHES

DO NOT

PULL ANTENNA!

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

SENSITIVITY

ADJUSTMENT

12”MOUNTING TUBE

SENSOR TRANSMITTER CAP

SENSOR TRANSMITTER BASE

MOUNTING

TUBE CAP

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

2 “C” BATTERIES
(NOT INCLUDED)

SENSOR TRANSMITTER

12”MOUNTING TUBE

MOUNTING STAKE

SENSOR TRANSMITTER

BOTTOM

SENSOR TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER BOTTOM
SCREWS

RECHARGEABLE NiMH BATTERIES

REMOVE PLASTIC TAB
FROM BATTERIES

DRIVEWAY

3’OR
LESS

25' OR MORE

PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.

12’

MAX

25' OR MORE

3' OR

LESS

FINGER NOTCHES

DO NOT

PULL ANTENNA!

WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION

SENSITIVITY

ADJUSTMENT

12”MOUNTING TUBE

1. Place cap on tube.

2. Insert stake to opposite end of tube.

3. Place the tube (stake side down) into the ground within 3’ of the driveway

and more than 25’ from the road.

4. Gently hammer the cap side of the tube until stake is firmly in the ground.

5. Remove cap and place sensor transmitter on tube.

6. The sensor transmitter should have a clear line-of-site to the receiver to

improve performance.

7. Place the sensor transmitter so the vehicle does not pass between it and

the receiver.

To obtain optimal range:

STI recommends the use of the stake and tube included with your Driveway
Monitor. However, if you choose to mount the unit to an alternate mounting
device, please be sure the device is stable. STI does not recommend
mounting the sensor transmitter to a tree or a metal fence or gate.

TROUBLE SOLUTION

1. Check that the receiver is not in Temporary or Permanent Silent Mode (red LED solid).

2. Check the sensor transmitter by picking it up and rotating it. The sensor transmitter should make
a “faint clicking” noise.

3. Check that the sensor transmitter and receiver are within operating distance from each other.

4. Check the sensor transmitter batteries and replace if necessary.

5. Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”

The RECEIVER does
not sound when a
vehicle passes.

1. Check that the sensor transmitter and receiver are within operating distance from each other.

2. Change the Sensitivity in the sensor transmitter using the steps in “Sensitivity Adjustment.”

3. Check that the sensor transmitter and receiver are located so a vehicle does not pass between
them.

4. Change the location of the sensor transmitter by placing it closer to the edge of the driveway.

5. Bring the sensor transmitter close enough to the receiver so the receiver button is visible. Test the
sensor transmitter by passing a steel shovel or large magnet around the sensor transmitter. The
sensor transmitter should make a “faint clicking” noise and the red LED on the receiver should
flash.

6. Check the sensor transmitter batteries and replace if necessary. On the solar powered driveway
monitor, make sure the sensor transmitter is in direct sunlight and has been charged in direct
sunlight for at least 48 hours after replacing batteries. Use only AA (1.2v) NiMH rechargeable
batteries.

7. Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”

The SENSOR
TRANSMITTER does
not activate when a
car passes.

1. Sensor transmitter mounted firmly and not effected by wind?

2. Sensor transmitter at least 25’ away from the main road?

3. Be sure there are no other metal objects near the sensor transmitter that may move.

4. Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”

The RECEIVER sounds
when there is no
vehicle passing.

Call STI Technical Support at 800-888-4784 ext 202.

Still having problems

— 3 —

Important notice:

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning

theequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
 •Reorientorrelocatethereceivingantenna
 •Increasetheseparationbetweentheequipmentordevices
 •Connecttheequipmenttoanoutletotherthanthereceiver’s
 •Consultadealeroranexperiencedradio/TVtechnicianforassistance
Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)thisdevicemustaccept

any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly
approved by Safety Technology International, Inc. could void your authority to operate this equipment.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

Warranty information:

Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in
material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase.

Inst. Sht. WirelessDriveway JUNE2013

Additional Wireless Alert Series Products:

STI-34099 Single Channel Slave Receiver
STI-34104 4-Channel Receiver
STI-V34104 4-Channel Voice Receiver
STI-34108 8-Channel Receiver
STI-34101 Solar Powered Driveway Monitor Sensor
STI-34151 Battery Powered Driveway Monitor Sensor
STI-34201 Wireless Mailbox Alert Sensor
STI-34301 Wireless Garage Sentry Sensor
STI-34401 Wireless Universal Alert Sensor
STI-34501 Wireless Pool Alert Sensor
STI-34601 Wireless Doorbell Button
STI-34701 Indoor Wireless PIR
STI-34751 Outdoor Wireless PIR

STI-6200WIR Wireless Fire Extinguisher Theft Stopper
STI-6200WIR4 Wireless Fire Extinguisher Theft Stopper w/Receiver
STI-6400WIR Wireless Exit Stopper Door Alarm
STI-6400WIR4 Wireless Exit Stopper Door Alarm with Receiver
STI-6517A Stopper Station Shield with Sound
STI-6517B Stopper Station Shield with Sound and Transmitter
STI-30104 Lamp Controller
STI-30105 Extended Antenna
STI-34105 Voltamax 12VDC (500mA) Power Supply
STI-34106 Keyfob
STI-34109 Repeater
STI-34188 8-Zone Relay Board

Safety Technology International, Inc.

2306 Airport Rd • Waterford, MI 48327

Phone: [phone] • Fax: [phone]

[e-mail] • www.sti-usa.com

Safety Technology International (Europe) Ltd.

Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: [phone]

Fax: [phone] • Freephone: 0800 085 1678 (UK only)

E-mail: [e-mail] • Web: www.sti-europe.com