Sterling SVF User Manual

STERLING SEPARATED COMBUSTION UNITS QVSB, QVSD, MS & SVFS HORIZONTAL CONCENTRIC VENT KIT (Option #M5)

HCVS-2

This Horizontal Concentric Vent Kit utilizes one 8 inch termination in which both the discharge flue gas and the combustion air inlet pases.

KIT CONTENTS

(1) Part No. 3603 –

Concentric Vent Box Assembly (See Figure 1)

(1) Part No. 3604 –

Inlet Air Screen

(1) Part No. 3605 –

Flue Terminal Assembly

(1) Tube –

Silicone Sealant

(1) Part No. IIMOW6/7 –

Installation Instructions

VENTING REQUIREMENTS

Standard two pipe venting and concentric vent kits are certified by A.G.A. and C.G.A. as venting methods for our Separated Combustion Models QVSB, QVSD and QVSF. No other venting arrangements are approved or certified for use with Sterling Separated Combustion Unit Heaters and Duct Furnaces.

All pipes are field supplied; 24 gauge single wall galvanized steel is recommended. All joints must be sealed with either high temperature silicone or aluminum foil tape.

The maximum vent length for the combustion air inlet is 50 equivalent feet. The maximum vent length for the flue gas outlet is also 50 equivalent feet. Allow 10 equivalent feet for each 90 degree elbow, and 5 equivalent feet for each 45 degree elbow. See Figures 2 and 3 for typical installations of the Sterling Horizontal Concentric Vent Kit.

Table 1

Unit Air Inlet Discharge

Capacity Size Flue Size

100, 125, 150, 200 4" (102mm) 4" (102mm)

200, 225, 250 5" (127mm) 5" (127mm) 300, 350, 400 6" (152mm) 6" (152mm)

Figure 1– Concentric Vent Box Assembly - Dimensional Data

Lock Seam

In. (203 Mm) Dia. tack Ext.

5 In.

(127 mm)

10 In.

(254 mm)

5 In.

(127 mm)

Stove Pipe Crimp

5 In. (127 mm) Dia. Stack Ext.

6 In. (152 mm) Dia.

Stack Ext's.

8 In.

(203 mm)

17 In.

(432 mm)

(51 mm)

4 In.

(102 mm)

(178 mm)

2 In.

7 In.

2 In.

(51 mm)

D4499

HVAC PRODUCTS

260 North Elm St., Westfield, MA 01085

(413) 564-5540 Fax: (413) 562-5311

www.sterlinghvac.com

PROJECT:

UNIT TAG:

HORIZONTAL CONCENTRIC VENT KIT (Option #M5)

Figure 2– Typical Horizontal Vent Kit Installation

Separated Combustion Unit

Terminate To Vertical Requirements Shown In Figure 3.

To Outside Vent Cap

D4500

Increasers As Required (Field Supplied)

Flue Discharge

(2) Mounting Brackets (Field Supplied)

Combustion Air Inlet

Wall

Figure 3– Typical Horizontal Vent Kit Installation Requirements

Reducer/increaser As Required (Reducer Is Field Supplied)

Power Venter Assembly

Fan/Motor Assembly

Top View

D4498-1

D4498-2

Inlet Air Screen Part# 3604

Rear View

16 In. (406) Min. 24 In. (610) Max.

Flue Terminal Assembly (Field) Part # 3605 (Shown) or (Breidert) Part # 2221-2

Wall

Thimble

17 In. (432)

Concentric Vent Box Part # 3603

7 In.

(178)

60 In. (1524) Max.

6 Ft. (1.8 m) Min.

30 Ft. (9.2 m) Max.

10 In. (254)

Size Pipes According To

Table 1.

Flue Discharge

Combustion Air Inlet

Size Pipes According To

Table 1.

Flue Discharge

Pitch Pipes To Drain 1/4" Per Foot

Combustion Air Inlet

Separated

Combustion

Unit

Separated

Combustion

Unit