Sterling Plumbing Wall Surround with Backer Boards 71124106, ENSEMBLE 71120118, ENSEMBLE 71120128, ENSEMBLE 71120116 Specification Sheet
Page 1
ENSEMBLETM
Features
Compression molded from our exclusive solid Vikrell
•
material
Tongue-and-groove 4-piece modular design allows for
•
easy ″snap together″ installation
Durable high-gloss finish
•
10-year consumer/3-year commercial limited warranty
•
Compatible with 71121110, 71121120, 71121112, and
•
71121122
Allows for future attachment of grab bars
•
Complete unit rough-in dimensions include flange
•
60-1/4″ (153 cm) x 33-1/4″ (84.5 cm) x 54″
•
(137.2 cm)
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASTM E162
•
ASTM E662
•
CSA B45.5/IAPMO Z124
•
BATH AND WALL SURROUND WITH
®
BACKER BOARDS
71120116
ALSO 71120118, 71120126, 71120128
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Specified Model
Model Complete Unit Description Colors/Finishes
71120116 32″ (81.3 cm) bath and wall surround with backer boards, left drain ❑ 0 ❑ Other_____
71120118 32″ (81.3 cm) bath and wall surround with backer boards, above-the-floor left
drain
71120126 32″ (81.3 cm) bath and wall surround with backer boards, right drain ❑ 0 ❑ Other_____
71120128 32″ (81.3 cm) bath and wall surround with backer boards, above-the-floor right
drain
Model Wall Component Description Colors/Finishes
71124106 Complete wall set with backer boards ❑ 0 ❑ Other_____
❑ 0 ❑ Other_____
❑ 0 ❑ Other_____
Page 1 of 2
1061193-4-
D
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Page 2
ENSEMBLETM
Technical Information
Fixture*:
Basin area:
Bathing well, bottom 42″ (106.7 cm) x 20″ (50.8 cm)
Bathing well, top 54″ (137.2 cm) x 26″ (66 cm)
To overflow:
Water depth 13-3/4″ (34.9 cm)
Capacity 55 gal (208.2 L)
* Approximate measurements for comparison only.
Model Door maximum
71120116
71120118
71120126
71120128
6" (15.2 cm)
width
57-11/16″ (146.5 cm) 55-1/2″ (141 cm)
14" (35.6 cm)
(Typical)
Door maximum
height
30" (76.2 cm)
Installation Notes
Install this product according to the installation guide.
End stud positioning is critical if nailing-in flanges are used.
Double studding is recommended for pivot shower door
installations.
Attach grab bars at the specified backer board locations only.
16" (40.6 cm)
33-1/4" (84.5 cm)
33-1/4"
(84.5 cm)
2" (5.1 cm) D. Drain
3-1/2"
(8.9 cm)
60" (152.4 cm) Min
60-1/8" (152.7 cm) Max
Back Wall End Wall
2" (5.1 cm)
1" (2.5 cm)
3-1/2" (8.9 cm)
Dimensions Taken From
Center of Grout Lines
15-1/2"
(39.4 cm)
30" (76.2 cm)
Grab Bar
8-1/2"
(21.6 cm)
8-1/2"
(21.6 cm)
12" (30.5 cm) 18" (45.7 cm)
Grab Bar
1"
(2.5 cm)
1" (2.5 cm)
22-1/2"
8"
(57.2 cm)
(20.3 cm)
4" (10.2 cm)
21"
(53.3 cm)
20" (50.8 cm)
18" (45.7 cm)
1" (2.5 cm)
42"
(106.7 cm)
Grab Bar
46" (116.8 cm)
2" (5.1 cm)
3-1/2"
(8.9 cm)
Attachment Block Locations
(Typically 1" (2.5 cm) Inside Grout Lines)
Product Diagram
1-1/4" (3.2 cm)
54"
(137.2 cm)
2"
(5.1 cm)
75-1/4"
(191.1 cm)
60"
(152.4 cm)
Overflow
Detail
2-7/8" (7.3 cm)
Note: Right and left end walls are
the same, only mirrored.
Backer board locations
ENSEMBLETM BATH AND WALL SURROUND WITH BACKER BOARDS
Page2of2
1061193-4-
D
Loading...