Sterling Bath Whirlpool 76111110, Bath Whirlpool 76111120, ENSEMBLE 76111110, ENSEMBLE 76111120 Specifications
ENSEMBLETM
Features
Compression molded from our exclusive solid Vikrell
•
material
Integral apron with removable access panel
•
Durable high-gloss finish
•
Pump with air switch and grounding-type plug-in cord
•
6 Jets
•
Optional three-piece wall set with generous storage
•
shelves
10-year consumer/3-year commercial limited warranty
•
16″ (406 mm) whirlpool bath depth (floor to top of
•
threshold)
60-1/4″ (1530 mm) x 43-1/2″ (1105 mm) x 20″
•
(508 mm) complete unit rough-in dimensions include
flange
60″ (1524 mm) x 42″ (1067 mm) x 19″ (483 mm)
•
complete unit finished dimensions include wainscot
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.19.7
•
ANSI Z124.1.2
•
ASTM E162
•
ASTM E662
•
UL 1795
•
HUD, UM Bulletin 73A
•
42″ (1067 mm) WHIRLPOOL BATH
®
76111110
ALSO 76111120
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Specified Model
Model Description Colors/Finishes
76 111110 42 ″ (1067 mm) whirlpool bath, left drain (shown) ❑ 0 ❑ Other_____
76111120 42″ (1067 mm) whirlpool bath, right drain ❑ 0 ❑ Other_____
Page 1 of 2
1021378-4-
H
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
ENSEMBLETM
Technical Information
Fixture*:
Basin area:
Bathing well 40″ (1016 mm) x 27″ (686 mm)
Top area 52″ (1321 mm) x 35″ (889 mm)
To overflow:
Water depth 11″ (279 mm)
Capacity 55 gal (208.2 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7
Model Door width Door maximum
76 111110
76111120
* Varies with alternative walls.
58-1/2″ (1486 mm) *NA
height
16"
(406 mm)
Required Electrical Service
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI):
Pump 120 V, 15 A, 60 Hz
Installation Notes
Install this product according to the installation guide.
Pump is supplied with a grounding type plug-in cord. Locate
the outlet behind the whirlpool, and within 24″ (610 mm) of
the pump.
Do not disassemble the pump or piping as this could void the
warranty.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical.
Studs should be positioned roughly as shown.
30" (762 mm)
14"
(356 mm)
6" (152 mm)
(Typical)
3-1/8" (79 mm)
Overflow Detail
24-1/2"
(622 mm)
1-1/2"
(38 mm)
3"
(76 mm)
60"
(1524 mm)
4"
(102 mm)
8"
(203 mm)
43-1/2"
(1105 mm)
42"
(1067 mm)
16"
(406 mm)
8-3/4"
(222 mm)
17-1/4"
(438 mm)
Drain Cutout
Ø 2" (51 mm) Drain
8-3/4"
(222 mm)
60-1/8" (1527 mm) Min
60-1/4" (1530 mm) Max
Product Diagram
3-1/2"
(89 mm)
19"
(483 mm)
43-1/2"
(1105 mm)
Pump
Motor
Location
20"
(508 mm)
Recommended Support Clip
Location (4 Total)
ENSEMBLETM 42″ (1067 mm) WHIRLPOOL BATH
Page2of2
1021378-4-
H
Loading...