REFERENCE
AND
INSTRUCTION MANUAL
OPTEC® 1000
VISION TESTER
Stereo Optical Company, Inc.
8600 W. Catalpa Ave., Suite 703, Chicago, IL 60656 USA
Phone: 1.773.867.0380 or 1.800.344.9500 Fax: 1.773.867.0388
Email: Sales@StereoOptical.com
www.StereoOptical.com
Optec is a registered trademark of Stereo Optical Company, Inc.
©2018 Stereo Optical Co.,
Inc. All rights reserved. Unless indicated otherwise, all trademarks are the
property of Stereo Optical Co., Inc. in the United States and other countries.
TABLE OF CONTENTS
I. Introduction 1
II. Vision Testing
2
III. Operating the Control Panel of the OPTEC
®
1000 3
a. Figure #1 4
IV. Administering the Tests
6
V. Maintenance of the OPTEC
®
1000 Vision Tester 7
VI. Figure #2
8
Figures #3 and #4
9
VII. Test Slides
10
1
I. INTRODUCTION
Good vision i
s a precious gift, which should be guarded, cherished,
and nurtured throughout life. To maintain good vision, frequent vision
screenings and periodic visual exams are necessary. In this way, an
awareness of inadequate vision or changes in vision can be noted. The
eye-care professional can then correct most visual problems. Without
these screenings, many children and adults would have undetected visual
difficulties, having a direct effect on their quality of life.
Eye-care professionals feel that the earlier vision screening can
begin, the more rewarding the results can be. This attention should be
continued throughout adult life, with specific attention to the working years.
Stereo Optical's OPTEC
®
1000 Vision Tester does this screening
very efficiently. It is a precision instrument designed to do quick, accurate,
reliable, and confidential screening. It will identify those who have a
problem and need professional assistance.
THE OPTEC® 1000 VISION TESTER
The OPTEC
®
1000 is engineered for ease of use. The instrument
is automatic with no moving parts. The instrument weighs only 12 pounds
and has a convenient handle for easy portability. The OPTEC
®
1000 can
be used on a desk, tabletop or countertop, requiring less than two square
feet of space. All tests are concealed in a closed housing which allows
only the subject being tested to view the targets.
2
The dispo
sable headrest tissues insure the applicant a hygienic
environment. The headrest also triggers the illumination for the test when
pressure is applied. If the subject backs off or is in the wrong position,
there will be no light in the instrument.
All tests required have been mounted on one easy to change
slide.
For the operator, all switches are conveniently located on a
remote control panel that can be placed anywhere for the operator's
convenience. Each switch is color coded for immediate identification.
II. VISION TESTING
To be a skillful tester you must become familiar with the
OPTEC
®
1000 Vision Tester.
Look into the instrument and note what happens when the eye
switches are ON and OFF. It is important to recognize whatever the
subject may be describing and be able to answer any questions.
Concentrate on acquiring a smooth delivery of instruction and description
of the test target. The tester's expertise can help relax the subject, get
better cooperation and a more accurate response.
3
When
speaking to the subject, never act surprised or provoked by
their responses or lack of response. Give the subject every opportunity to
demonstrate their best vision.
If the subject is wearing glasses or contact lenses, they should
wear them during the testing to determine whether they meet the
requirements for corrected vision.
The table or counter should be of convenient height with sufficient
surface space for the instrument. Normal room lighting is acceptable, but
care should be taken to avoid light shining on the lenses or on the
subject's face.
III. OPERATING THE OPTEC
®
1000
The first step is to connect the control panel to the instrument.
Connect the multi-prong plug to the back of the control panel. The plug will
fit in only one way. Push the plugs together and tighten the screw on each
side of the plug. You should not have to unplug the control panel once you
have joined the instrument and panel together.
Plug control panel into an electrical outlet by using the black cord
with the three (3) prong plug. (110 V AC)
CONTROL PANEL OPERATIONS
CONTROL SWITCHES: From left to right; (see figure #1)
4
Figure #1
TOP ROW:
First: Right Eye Switch: Orange color; when the switch is turned
ON (depressed) the right eye will see the target, when the
switch is turned OFF (raised) the right eye will see nothing.
Second: Left Eye Switch: Green color; same as above. When both
switches are ON together, the subject will see with both eyes
(binocularly).
Third: Day/Night Control: White color; when this switch is raised,
daylight conditions are simulated in the instrument. When the
switch is depressed, night-time conditions are simulated in the
instrument.
Most testing is done under day-light conditions.
Fourth: Power Switch: Red color; this controls the power for the
instrument. Depressed, the power is ON. Raised, the power is
OFF.
5
Fifth: Ready Light: Green color; this will light when the subject
applies pressure to the headrest trigger and is in the proper
position to be tested.
MIDDLE ROW: Perimeter Test
First: Yellow Color: 45° nasal perimeter test. When the switch is
held down, a momentary light will flash in the face plate. The
light will appear on the opposite side from the side you are
testing.
Second: Blue Color: 55° temporal perimeter test
Third: Blue Color: 70° temporal perimeter test
Fourth: Blue Color: 85° temporal perimeter test
These switches are momentary. They will only flash as long as
pressure is applied and will flash along the side you are testing. The
same switches are used for testing both right and left sides. Turn the
eye switch off for the eye not being tested.
BOTTOM ROW: Test Switches
First: TEST #1: White color; depress switch and test will be
illuminated. Press again to turn illumination off when test is
finished. Proceed to TEST #2.
Second, Third and Fourth: TEST #2, #3 AND #4: White color; same as
above. If you are only doing one test, you can leave it on and
the light will go off or on automatically as the subjects apply
pressure to the headrest trigger.
6
IV. ADMINISTERING THE TEST
Turn the power on by depressing the red power switch. Depress
the two eye switches--orange and green, being sure the white switch
(day/night) is NOT
depressed but in the raised position. Pull off the first
headrest tissue so there is a clean tissue available for the subject.
Have a subject step forward and adjust the height of the
instrument. Have the subject hold the instrument with both hands, one on
each side, looking into the lenses. The subject's forehead should press
against the headrest trigger. The green ready light on the control panel
should light.
Depress the switch marked TEST #1 and administer the test.
Check your score key for correct answers. Depress switch marked TEST
#1 again so it will turn off. Proceed to switch marked TEST #2 for the next
test. Continue this process until all testing is completed.
PERIMETER TESTING
Ask the subject to look straight ahead. Use the top line of the
center column of an acuity test as a fixation point. Turn left eye off (switch
raised). Press the switches in the middle row of the control panel in any
sequence. Ask the subject to point to where they see a light flashing. Once
you have gone through all four positions, turn the left eye on and the right
eye off, following the same procedures.
IMPORTANT CHECKPOINTS:
• Be certain the instrument is plugged into a 110-120V AC outlet.
7
• Push
RED power switch on control panel to activate the
instrument.
• Check both eye switches to be certain they are depressed (ON).
• Tear off headrest tissue so a clean tissue is ready for the next
subject.
• Be certain the subject presses their forehead against the headrest
trigger so the illumination in the unit is activated and the GREEN
"READY" indicator on the control panel is lit.
• Be certain you have a score key available.
V. MAINTENANCE OF THE
OPTEC
®
1000 VISION TESTER
Stereo Optical's OPTEC® 1000 Vision Tester was designed to
minimize maintenance. It has been engineered and built for a lifetime of
use. The only annual maintenance required is simple and does not
necessitate a service call. There are no moving parts with the
OPTEC
®
1000.
The only components requiring occasional maintenance are:
• EYEPIECE LENSES: The external sides of these lenses need to
be cleaned occasionally (see figure #2). Care should be taken not
to use any abrasive material on these lenses. Use the cleaner
supplied with the vision tester. It is important to dry the lenses with
a soft cotton cloth or tissue.
• CLEANING OF SLIDE: Open the slide cover door and remove
the slide. Use a damp soft cloth or tissue with lens cleaner and
wipe both sides of the slide.
8
• EXTERIOR: The aluminum and ABS plastic of which the
instrument body is made can be cleaned with a damp cloth and a
mild detergent. Make sure control panel is disconnected.
• CHANGING LIGHT BULBS: When you have a burned out bulb,
identify which test is affected. Turn the power (RED switch) off.
Unplug the instrument from the electrical outlet. Remove screws
from top left and right rear of instrument. Take a firm grasp of the
two knobs in the center of the back door and pull back and down
(see figure #3). The door will open and the eight (8) light bulbs will
be exposed (see figure #4). With two fingers slide the burned-out
bulb and socket out. Replace the bulb with a blue coated bulb,
(Optec
®
2000-226). It is suggested that you replace the bulb
opposite the burned out one at the same time. Slide the socket
and bulb back into the track with the screw head on the socket top,
on the outside of track. Close the door and replace the two screws.
Turn power back on by plugging the cord into wall socket and
depressing the red switch. You are now ready to continue testing.
Figure #2
9
Figure #3
Figure #4
10
VII. TEST SLIDES
MULTIPLE ACUITY TEST SLIDE (1000-23)
ALLEN ACUITY TEST
1. Test #1
2. Both Eyes Illuminated
20/100
20/50
20/40
20/30
Before doing the Pre-School test use the two training cards supplied with
the Vision Tester to familiarize the child with the pictures he or she will see
in the Vision Tester. Review the training cards until the child is familiar and
comfortable with the pictures. Ask the child to identify the pictures in the
top line. Correctly identifying three or more pictures is a pass on this line.
• Read from left to right
• Both Eyes: 20/100 Top Line - Car, Phone, Birthday Cake, Horse
3. Test #2
4. Right Eye Illuminated
5. Left Eye Occluded
Now continue with lines A, B, and C. The last line in which the child
correctly identifies three or more pictures is their Acuity level. Repeat the
test with the left eye illuminated.
11
MULIPLE ACUITY TEST SLIDE (1000-023)
LETTER ACUITY
1. Test #3 & 4
2. Right & Left Eye Illuminated
20/200
20/100
20/70
20/50
20/40
20/30
20/20
Left Eye Right Eye
Ask the subject, "How many columns of letters do you see?" The answer is
three.
Then ask the subject to read line 5 completely. If this is correct, proceed to
line 6, if correct proceed to line 7, if correct, the subject has 20/20 vision, or
better, in the right eye, left eye, and both eyes together. The scoring key is
printed on the record form.
Two or more letters incorrectly identified on any one of lines (3 to 7) PER
COLUMN, is considered a FAIL for that acuity level IN THAT COLUMN.
A DIFFERENT ACUITY READING FOR EACH COLUMN IS POSSIBLE
WITH THE CENTER COLUMN BEING THE MOST CRITICAL. It is critical
because this is the binocular acuity test, while the right and left columns
are only monocular acuity tests. Our actual vision is binocular, not
monocular.
12
A monocular acuity test can be administered on the right or left eye by
occluding the eye not being tested. With one eye occluded, the subject will
only see two columns with letters.
Some of the binocular irregularities that can occur are:
1. Either right or left column appears fuzzy and blurred
2. A complete lack of targets in either right or left column will indicate a
vision problem
3. An intermittent disappearance of targets in either the right or left column
4.
Failure to fuse the right and left eye area of the slide into three columns
of letters
13
ELEMENTARY TEST SLIDE (1000-22)
TUMBLING “E” ACUITY
1. Test #1 & 2
2. Right Eye Illuminated
3. Left Eye Occluded
20/50
20/40
20/30
20/20
Left Eye Occluded Right Eye
Ask the child
to identify the direction the E’s are pointing: up, down, right,
or left, in the top line, starting with the large E. Confirm the last correct
answer by having the child read the corresponding line A, B, C, or D.
For example, the child has read through #4 correctly, 20/40 vision. The
child should then read line B (20/40).
The correct reading of four of the six symbols confirms 20/40 vision.
Proceed to line C; a correct reading of four of the six symbols will confirm
20/30. Then proceed to line D will be the same format. If read correctly, the
child has 20/20 vision.
20/200
20/100
20/70
20/50
20/40
20/30
20/20
14
Rep
eat with opposite eye. (Slide 1000-22)
20/50
20/40
20/30
20/20
Left E
ye Right Eye Occluded
THE PLUS LENS SYSTEM
• The plu
s lens system tests for excessive farsightedness
(hyperopia). The plus lens system supplied with the
"OPTEC
®
1000 Vision Tester" is a plus 1.75D; other powers are
available as optional equipment
• A child scoring 20/40 or poorer on TESTS #1 & #2 should not be
given the plus lens test. (Tests #3 & #4)
• Insert the lens into the slot at the top of the face plate with the label
away from the subject
• A child with normal vision will NOT be able to read the 20/20 line
through the plus lenses, a PASS.
• If the child CAN read the 20/20 line through the plus lens, he then
FAILS the test.
• The ability to clearly read 20/20 through plus lenses is abnormal
and could indicate excessive farsightedness.
• This test is very important for school age children
20/200
20/100
20/70
20/50
20/40
20/30
20/20
15
ELEMENTARY TEST SLIDE (1000-22)
VERTICAL & LATERAL PHORIA
1. Test #3
2. Right Eye ON
3. Left Eye Occluded
Left Eye Right Eye
Example of Viewing Slide with Both Eyes
Ask the child if he sees a box, the answer is affirmative. Then tell the child
a red ball is being thrown at the box, simultaneously, turn the LEFT Switch
ON.
Question: "Where does the ball land, in or out of the box?" Anywhere in
the box is PASS, outside the box is FAIL.
Record the initial response.
16
ELEMENTARY TEST SLIDE (1000-22)
COLOR PERCEPTION
1. Test #4
2. Right & Left Eye Illuminated
Left Eye Right Eye
This color perception slide is made for a visual acuity of 20/50 or better in
both eyes. If the subject’s vision is below 20/50 he will fail the test, not
because of a color perception problem, but because of low acuity.
A person with normal color perception can identify the E's in each of the
eight blocks.
Acceptable color perception is correctly identifying five of the eight E' s.
Blocks 2 and 3 are the most difficult to identify, so it is recommended to
test block 1 then 4, 5, 6, 7, 8 and then come back to 2 and 3.
Question: To test, ask the child “Which way the E is pointing in each block?
The answer should be up, down, right or left, starting with block #1.
17
SECONDARY TEST SLIDE (1000-021)
LETTER ACUITY
1. Test #1 & 2
2. Right & Left Eye Illuminated
20/200
20/100
20/70
20/50
20/40
20/30
20/20
Left Eye Right Eye
Ask the subj
ect, "How many columns of letters do you see?" The answer is
three.
Then ask the subject to read line 5 completely. If this is correct, proceed to
line 6, if correct proceed to line 7, if correct, the subject has 20/20 vision, or
better, in the right eye, left eye, and both eyes together. The scoring key is
printed on the record form.
Two or more letters incorrectly identified on any one of lines (3 to 7) PER
COLUMN, is considered a FAIL for that acuity level IN THAT COLUMN.
A DIFFERENT ACUITY READING FOR EACH COLUMN IS POSSIBLE
WITH THE CENTER COLUMN BEING THE MOST CRITICAL. It is critical
because this is the binocular acuity test, while the right and left columns
are only monocular acuity tests. Our actual vision is binocular, not
monocular.
18
A monocula
r acuity test can be administered on the right or left eye by
occluding the eye not being tested. With one eye occluded, the subject will
only see two columns with letters.
Some of the binocular irregularities that can occur are:
1. Either right or left column appears fuzzy and blurred
2.
A complete lack of targets in either
right or left column will indicate a
vision problem
3. An intermittent disappearance of targets in either the right or left column
4. Failure to fuse the right and left eye area of the slide into three columns
of letters
19
SECONDARY TEST SLIDE (1000-21)
LATERAL PHORIA
1. Test #3
2. Right Eye Illuminated
3. Left Eye Occluded
Left Eye Right Eye
Ask the subj
ect, "Do you see a series of musical notes?" If the subject
does, ask, "How many?" The answer is 15. Tell the subject a white arrow
will appear. Simultaneously turn LEFT switch ON. Ask the subject, "The
arrow is pointing to which note?" An immediate response is desired.
The Lateral Phoria Test measures the relative posture of the eyes in the
horizontal plane. The arrow pointing to #8 is the ideal orthophoric, but the
arrow anywhere between #3 ½ and #12 ½ is within the accepted norms.
• Each number represents one(1) prism diopter of power.
• Exophoric scores are measured from note #8 to #15.
• Esophoric scores are from note #1 to #8.
NOTE: This test cannot be given to a subject with vision in only one eye.
This is a binocular test only.
20
SECONDARY TEST SLIDE (1000-21)
VERTICAL PHORIA
1. Test #4
2. Right Eye Illuminated
3. Left Eye Occluded
Left Eye Right Eye
Ask the subject, "Do you see a series of musical notes?" If the subject
says, “yes”, ask, "How many?" The answer is 7. Tell the subject a red
broken line will appear. Simultaneously turn LEFT switch ON.
Ask the subject, "The line crosses the round part of which note?"
The red broken line passing through note #4 is ideal or orthophoric.
Anywhere from 2 ½ to 5 ½ is the accepted norm.
The Vertical Phoria Test measures how the eyes work together on the
vertical plane.
• Each number represents ½ prism diopter of power.
NOTE: This test cannot be given to a subject with vision in only one eye;
this is a binocular test only.
PN 56179
Stereo Optical Company, Inc.
8600 W. Catalpa Ave., Suite 703, Chicago, IL 60656 USA
Phone: 1.773.867.0380 or 1.800.344.9500 Fax: 1.773.867.0388
Email: Sales@StereoOptical.com
www.StereoOptical.com
Optec is a registered trademark of Stereo Optical Company, Inc.
©2018 Ste
reo Optical Co., Inc. All rights reserved. Unless indicated otherwise, all trademarks are the
property of Stereo Optical Co., Inc. in the United States and other countries.
Loading...