Page 1
Table Of Contents
Congratulations on the purchase of your new motorized treadmill. To help ensure the
enjoyable and trouble-free operation of your new treadmill, we strongly suggest you read this
manual carefully and follow its recommendations.
MX850
MX800
Important Safety Instruction ..............1
Assembly Instruction .........................2
CONSOLE OPERATION ..................4
Preset Program .................................9
Utilizattion .....................................12
Maintenance...................................13
2006/11(MX8-3)
Page 2
Never use extension cords between the treadmill
and wall outlet.
,
1
Pls pay attention , the power cable need individual power source strictly ,
can not be usage mutual power supply with another equipment.
Page 3
10
11
12
13
14
15
16
17
1
2
3
4
5
6
7
8
9
Frame
Base frame
Support handle-Left
Support handle-Right
Handlebar-Left
Handlebar-Right
Console bracket
Handle rail
Console
Rack-Left
Rack-Right
Base frame cover-Left
Base frame cover-Left
Base frame cover-Left
Base frame cover-Right
Base frame cover-Right
Base frame cover-Right
Parts
Since your treadmill is a heavy piece of equipment, we recommend that after taking off the top portion of the box,
you slit the corners of the lower carton and fold down the sides. This will eliminate the need for you to pick up the
treadmill over the sides of the box.
Prior to starting the assembly process take all of the parts out of the box, remove all plastic bags, and lay them out
on the floor to become familiar with the compoents. Make sure that you remove all parts packaged underneath the
readmill. You may need to slightly pick up the back of the treadmill to get better access to the parts on the bottom.
You will notice that the treadmill is completely assembled except for the handlebars and the display window.
MX800/MX850
21
23
18
17
22
21
22
21
22
8
11
9
23
20
22
22
21
19
23
19
13
20
22
23
14
10
23
23
16
18
3
5
6
12
1
2
4
15
24
24
Hardware、tool
Screws Already in Place on the Treadmill
22
M8(12PCS)
washer
Tool
18
SCREWS
M10*75L(2PCS)
19
M10*10t(2PCS)
20
SCREWS
M8*15L(6PCS)
21
SCREWS
M8*20L(6PCS)
23
SCREWS
M4*10L(14PCS)
nylon nut
24
#8*5/8"L(4PCS)
SCREWS
28
(1PCS)
25 26 27
Wrench-6mm
T Handle
Wrench
Triangle screw
driver
Wrench
(1PCS) (1PCS) (1PCS)
Page 4
Step 1: Handlebars assembly
MX800/MX850
3
Step 2: Racks assembly
Step 3: Compete assembly
FIG-6
FIG-7
23
23
FIG-9
22
FIG-8
8
21
22
21
7
1. Flat the shipping box and take out packing material, Styrofoam, parts, screw bag and manual etc. from box.(FIG 1)
2. Remove screws/washers 18 19 20 22 from base frame and screws/washers 21 22 from Right/Left handle bar.(FIG 2)
3. Upright the completed support handles and handlebars.Pls set up handle bar 5 6 with supporting handle 3 4 by
attached 21 22 screw and washer and fix it.(FIG 3)
4. Attach and tighten screw 18 and nut 19 on left support handle. Attach and tighten screw 20 and washer 22 on right
support handle. Repeat the same on right side.(FIG 4)
5. Attach base frame covers 13 and 14 to match cover 12 on left base frame and then tighten with screws 23 24. (FIG 4)
6. Repeat the same on right side for base frame covers 15 16 17 . (FIG 5)
Warning:
1. Be careful to avoid machine tilt or getting hurt.
2. Do not have the wire harness(inside of handlebars) get pinched.
1. Attach and tighten screw and washer 21 22 on
right/left handlebars.
2. Attach left rack 10 on left handlebar and tighten with
screws 23.
3. Repeat the same on right side for right rack
assembly.
14
23
24
24
23
13
3
4
6
5
20
22
18
12
19
FIG-5
20
22
18
19
15
1. Attach handle rail on handlebar and then tighten with
screws/washers 21 22. (FIG 8)
2. Adjust console bracket 7 and console to a proper
position and then tighten the 4 pcs of screws 20 22
underneath of handlebar. (FIG 9)
FIG-3
22
21
18
19
19
18
22
20
22
20
22
21
4
21
22
21
22
20
22
20
22
22
20
Page 5
4
MX800
Buttons and Windows
Incline up:
This will select program/level in setting mode before starting.
This will increase the elevation in 1 increment.
Incline down:
This will select program/level in setting mode before starting.
This will decrease the elevation in 1 increment.
START/STOP:
This will start the treadmill and this will stop the
treadmill. There will also be an emergency stop switch.
(Safety Key)
MODE:
This will accept programs/level selection. And this
will switch display data on data window during exercise.
SPEED up:
This will select program/level in setting mode before starting.
This will increase the speed in 0.1 km/h or 0.1 mph
SPEED down:
This will select program/level in setting mode before starting.
This will decrease the speed in 0.1 km/h or 0.1 mph
ENTER:
This will set-up each program. into every step.
Quick keys for speed /incline:
Quick keys for incline: 4,6,8,10
Quick keys for speed: 4,6,8,10(km/hr)
If the light under each button is flashing, it means
to use that button for next setup process.
There are 1 LCD window and 3 LED windows.
1)WIN0(Incline) window: shows level of incline
2)WIN1:shows Time, Distance, Calories, Pulse, Lap, Scan
3)WIN2(Speed) window: shows speed
Handlebar toggle for incline and speed adjustment
1. Left: for incline adjustment. Increase or decrease by 1 every time.
2. Right: for speed adjustment. Increase or decrease by
0.1 km/hr every time.
Page 6
5
MX850
Buttons and Windows
Incline up:
This will select program/level in setting mode before starting.
This will increase the elevation in 1 increment.
Incline down:
This will select program/level in setting mode before starting.
This will decrease the elevation in 1 increment.
START/STOP:
This will start the treadmill and this will stop the
treadmill. There will also be an emergency stop switch.
(Safety Key)
MODE:
This will accept programs/level selection. And this
will switch display data on data window during exercise.
SPEED up:
This will select program/level in setting mode before starting.
This will increase the speed in 0.1 km/h or 0.1 mph
SPEED down:
This will select program/level in setting mode before starting.
This will decrease the speed in 0.1 km/h or 0.1 mph
ENTER:
This will set-up each program. into every step.
Quick keys for speed /incline:
Quick keys for incline: 4,6,8,10
Quick keys for speed: 4,6,8,10(km/hr)
If the light under each button is flashing, it means
to use that button for next setup process.
There are 4 LED windows and 12 Alpha numeric display.
Handlebar toggle for incline and speed adjustment
1. Left: for incline adjustment. Increase or decrease by 1 every time.
2. Right: for speed adjustment. Increase or decrease by
0.1 km/hr every time.
Page 7
6
TFT-LCD TV
MENU Mode: Allowing user to adjust the value of Brightness, Contrast, Color and Tint.
1.Hold "MODE" for 3~4 seconds into "MENU"model. Using button CH+ and CH- to select the item you like to
set up.
2.Using button VOL+ and VOL- to adjust value of each item as below.
Press to power on or power off TV display.
AV/TV
CH+
CH-
VOL+
VOL -
Button function:
Button Function
1. Press to select TV/Video/MP3 Function. TV-AV-MP3
2. Hold for 3~4 seconds: enter into "MENU" to setup screen.
1. In TV mode: Press to select channel.
2. In MENU mode: Press to select item to set up.
1.In TV/Vedio/MP3 mode: Press to adjust volume.
2. In MENU mode: Press to adjust the value of each item.
POWER ON/OFF
Item
BRIGHTNESS
CONTRAST
SHARP
COLOR
TINT
MUTE
TV SYSTEM
AUTO SCAN
RESET
QUIT
Description
Adjust BRIGHTNESS. 0 ~ 63
Adjust CONTRAST. 0 ~ 63
Adjust SHARP. 0 ~ 7
Adjust COLOR. 0 ~ 63
Adjust TINT. 0 ~ 63
Mute ON/OFF
Select TV system. NTSC-M、NTSC-J、PAL-BG、PAL-DK、PAL-AI、
SECAM-BG、SECAM-DK、SECAM-L according to Tuner.
ON/OFF
Return to DEFAULT value.
Press VOL+ or VOL- to exit MENU mode.
Page 8
7
MX800/MX850
Manual Function
12 Preset Programs
Target Heart Rate Program
This program automatically modifies the speed and incline to maintain a preset target heart
rate. This target is established in the setup process. The chart on this owners manual should
be used to determine the appropriate target heart rate. To set up the target heart rate program,
you will need to enter the workout time, age, your target heart rate and max. desired speed.
1. Attach safety key and press "MODE" into selecting program mode.
2. Using speed arrow buttons to choose "HRC" program. Then press "ENTER".
3. Using speed or incline arrow buttons to input your age (13-80). Then press "ENTER".
4. Using speed or incline arrow buttons to input your target heart rate (60-180). Then press "ENTER".
5. Using speed arrow buttons to input max. desired speed (3-20). Then press "ENTER".
6. Using speed or incline arrow buttons to input Max, desired incline (5-15). Then press "ENTER".
7. Using speed or incline arrow buttons to input workout time (10~99 Min.) . Then press "START".
Console of 3LED & 1LCD is with 1 Manual function, 12 preset programs, 1 H.R.C program,
Body Mass and 2 user setting programs.
Console of 4 LED & 12 character Alphanumeric LED is with 1 Manual function, 12 preset
programs, 1 H.R.C program.
MX800: 1. Attach safety key and press "MODE" into selecting program mode.
2. Using speed arrow buttons to choose "Manual" function, then press "ENTER".
3. Time window is flashing. Using speed or incline arrow buttons to input workout time (10~99 Min.)
4. Press "START".
MX850: 1. Attach safety key and 12 Alpha bumericdisplay shows "Welcome To Strength Master".
2. Press "Mode" into Mannual aditing mode. 12 Alpha numeric display shows "SET TIME".
3. Using speed or incline arrow buttons to input workout time.(10~99 Min.) Press "ENTER".
4. Press "START".
P1~P5: Automatically change the speed of the treadmill throughout the workout.
P6~10: Automatically change the level of incline for the treadmill belt.
P11: 5km distance program. Automatically change the level of incline for the treadmill belt. The user sets the
speed to a desired level and the program modifies the incline. The user can override the incline for any
segment within the workout but at the end of each workout segment the program will override any
adjustments made to the incline.
P12: 10km distance program. Automatically change the level of incline for the treadmill belt. The user sets
the speed to a desired level and the program modifies the incline. The user can override the incline fo
rany segment within the workout but at the end of each workout segment the program will override any
adjustments made to the incline.
1. Attach safety key and press "MODE" into selecting program mode.
2. Using speed arrow buttons to choose desired preset program "P1~P12". Then press "ENTER".
LCD window shows speed (P1~P5) or incline (P6~P12)
3. Using incline arrow buttons to choose desired level (L1~L3). Then press "ENTER"
4. Using speed or incline arrow buttons to input workout time (10~99 Min.)
Page 9
8
MX800/MX850
1. Attach safety key and press "MODE" into selecting program mode.
2. Using speed arrow buttons to choose "Body Mass" program. Then press "ENTER".
3. Using speed or incline arrow buttons to input your sex, height, weight, and age. Then press "ENTER".
4. LCD window shows "Please Hold". Please hold the hand pulse grips.
5. It shows BMI on LCD window value after 25 seconds measurement.
Notes:
1) It shows E4 if it does not read signal from hand pulse grips.
1. Attach safety key and press "MODE" into selecting program mode.
2. Using speed arrow buttons to choose "User 1" or "User 2" program. Then press "ENTER".
3. Using speed or incline arrow buttons to input workout time. (10~99 Min.) Then press "ENTER".
4. During setup process: Incline window shows level of incline, Time window shows number of segment,
Speed window shows speed level.
5. Using incline arrow buttons to input level of incline for each segment. Using speed arrow buttons to input
speed level for each segment. Then press "ENTER" for next segment till finish all 30 segments.
Notes:
1) After press "START", there is a warming period for first 3 minutes at incline level 5 and speed 3.0km/hr.
2) After warming up, the program compares actual heart rate and target heart rate every 12-15 seconds.
3) If the actual heart rate is less than target heart rate, increases speed by 0.2km/h every time and
increases incline by 1 once changing speed by 5 times. If the actual heart rate is reached target heart
rate, decreases speed by 0.2km/h every time and decreases incline by 1 once changing speed by 5
times.
4) If the speed is increased up to max. target speed, then speed can not be increased anymore
eventhough the actual heart rate is still less than target heart rate.
5) If it does not read heart rate signal from user in 30 seconds after warming up period, the treadmill
stops into runend mode.
under weight 20
IBW 21~24
Overweight 25~29
Overweight 30~34
Overweight 40
Body Mass Index Comparison table
>
=
Body Mass
(Only for MX800)
User setup programs
(Only for MX800)
TARGET HEART RATE PROGRAM: This program automatically modifies the speed and incline to maintain a
preset target heart rate. This target is established in the setup process. The chart on this owners manual should be
used to determine the appropriate target heart rate. To set up the target heart rate program, you will need to enter the
workout time, your age, and your target heart rate.
Increased Performance Range
Aerobic Training Range
Weight Loss Training Range
Heart Rate BPM
Page 10
9
MX800
P1 P2 P3 P4 P5
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
SEGMENT
P1
1 2 3 4 5 6 7 8 9
P2
P3
P4
P5
2 2 2 3 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2 3 3 2 2
3 3 3 4 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3 4 4 3 3
4 4 4 5 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4 5 5 4 4
2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 6 6 6 4 4 4 2 2 2
3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 7 7 7 5 5 5 3 3 3
4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 8 8 8 6 6 6 4 4 4
2 2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3 2 2 2
3 3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3
4 4 4 6 6 6 8 8 8 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4
1 1 1 3 3 3 6 6 6 7 7 7 7 8 8 8 8 7 7 7 7 6 6 6 3 3 3 1 1 1
2 2 2 4 4 4 7 7 7 8 8 8 8 9 9 9 9 8 8 8 8 7 7 7 4 4 4 2 2 2
3 3 3 5 5 5 8 8 8 9 9 9 9 9 9 9 9 8 8 8 5 5 5 3 3 3
1 1 1 7 7 7 2 2 2 9 9 9 9 2 2 2 2 9 9 9 9 2 2 2 7 7 7 1 1 1
2 2 2 8 8 8 2 2 2 3 3 3 3 2 2 2 8 8 8 2 2 2
3 3 3 9 9 9 2 2 2 4 4 4 4 2 2 2 9 9 9 3 3 3
P6
P7
P8
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
P9
2 2 2 3 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2 3 3 2 2
3 3 3 4 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3 4 4 3 3
4 4 4 5 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4 5 5 4 4
Speed
Program
10 10 10
10 10 10 10
10 10 10 10
10 10 10
10 10 10 10
11 11 11 11 11 11 11 11
P10
P11
P12
Incline
Program
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 6 6 6 4 4 4 2 2 2
3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 7 7 7 5 5 5 3 3 3
4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 8 8 8 6 6 6 4 4 4
2 2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3 2 2 2
3 3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3
4 4 4 6 6 6 8 8 8 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4
1 1 1 3 3 3 6 6 6 7 7 7 7 8 8 8 8 7 7 7 7 6 6 6 3 3 3 1 1 1
2 2 2 4 4 4 7 7 7 8 8 8 8 9 9 9 9 8 8 8 8 7 7 7 4 4 4 2 2 2
3 3 3 5 5 5 8 8 8 9 9 9 9 9 9 9 9 8 8 8 5 5 5 3 3 3
1 1 1 7 7 7 2 2 2 9 9 9 9 2 2 2 2 9 9 9 9 2 2 2 7 7 7 1 1 1
2 2 2 8 8 8 2 2 2 3 3 3 3 2 2 2 8 8 8 2 2 2
3 3 3 9 9 9 2 2 2 4 4 4 4 2 2 2 9 9 9 3 3 3
2 2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3 2 2 2
3 3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4 3 3 3
4 4 4 6 6 6 8 8 8 9 9 9 8 8 8 7 7 7 6 6 6 5 5 5 4 4 4
2 2 2 3 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2 3 3 2 2
3 3 3 4 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3 4 4 3 3
4 4 4 5 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4 5 5 4 4
10 10 10
10 10 10
10 10 10 10
10 10 10 10 10 10 10 10
11 11 11 11 11 11 11 11
10 10 10
(5km)
(10km)
P6 P7 P8 P9 P10 P12
(10km)
P11
(5km)
Speed Program:
Incline Program:
Page 11
10
MX850
P1 P2 P3 P4 P5
P6 P7 P8 P9 P10 P12
(10km)
P11
(5km)
Speed Program:
Incline Program:
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
SEGMENT
P1
1 2 3 4 5 6 7 8 9
P2
P3
P4
P5
2 2 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2
3 3 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3
4 4 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4
2 2 3 3 4 4 5 5 6 6 7 7 7 8 8 8 6 6 6 4 4 4 2 2
3 3 4 4 5 5 6 6 7 7 8 8 8 9 9 9 7 7 7 5 5 5 3 3
4 4 5 5 6 6 7 7 8 8 9 9 9 8 8 8 6 6 6 4 4
2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 5 5 4 4 3 3 2 2
3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 6 6 5 5 4 4 3 3
4 4 6 6 6 8 8 8 9 9 9 8 8 7 7 6 6 5 5 4 4
1 1 3 3 6 6 6 7 7 7 8 8 8 8 7 7 7 6 6 6 3 3 1 1
2 2 4 4 7 7 7 8 8 8 9 9 9 9 8 8 8 7 7 7 4 4 2 2
3 3 5 5 8 8 8 9 9 9 9 9 9 8 8 8 5 5 3 3
1 1 7 7 7 2 2 2 9 9 9 2 2 9 9 9 2 2 2 7 7 7 1 1
2 2 8 8 8 2 2 2 3 3 2 2 2 8 8 8 2 2
3 3 9 9 9 2 2 2 4 4 2 2 2 9 9 9 3 3
P6
P7
P8
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
P9
2 2 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2
3 3 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3
4 4 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4
Speed
Program
10 10 10
10 10 10 10
10 10 10
11 11 11
P10
P11
P12
Incline
Program
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
2 2 3 3 4 4 5 5 6 6 7 7 7 8 8 8 6 6 6 4 4 4 2 2
3 3 4 4 5 5 6 6 7 7 8 8 8 9 9 9 7 7 7 5 5 5 3 3
4 4 5 5 6 6 7 7 8 8 9 9 9 8 8 8 6 6 6 4 4
2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 5 5 4 4 3 3 2 2
3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 6 6 5 5 4 4 3 3
4 4 6 6 6 8 8 8 9 9 9 8 8 7 7 6 6 5 5 4 4
1 1 3 3 6 6 6 7 7 7 8 8 8 8 7 7 7 6 6 6 3 3 1 1
2 2 4 4 7 7 7 8 8 8 9 9 9 9 8 8 8 7 7 7 4 4 2 2
3 3 5 5 8 8 8 9 9 9 9 9 9 8 8 8 5 5 3 3
1 1 7 7 7 2 2 2 9 9 9 2 2 9 9 9 2 2 2 7 7 7 1 1
2 2 8 8 8 2 2 2 3 3 2 2 2 8 8 8 2 2
3 3 9 9 9 2 2 2 4 4 2 2 2 9 9 9 3 3
2 2 4 4 4 6 6 6 8 8 8 7 7 7 6 6 5 5 4 4 3 3 2 2
3 3 5 5 5 7 7 7 9 9 9 8 8 8 7 7 6 6 5 5 4 4 3 3
4 4 6 6 6 8 8 8 9 9 9 8 8 7 7 6 6 5 5 4 4
2 2 3 3 4 4 4 3 3 3 2 2 2 3 3 3 4 4 4 3 3 3 2 2
3 3 4 4 5 5 5 4 4 4 3 3 3 4 4 4 5 5 5 4 4 4 3 3
4 4 5 5 6 6 6 5 5 5 4 4 4 5 5 5 6 6 6 5 5 5 4 4
10 10 10
10 10 10
10 10 10 10
10 10 10
11 11 11 11 11 11
10 10 10
(5km)
(10km)
10 10 10
10 10 10
11 11 11
10 10 10
Page 12
TFT-LCD TV
11
SEGMENT
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
Speed
Program
Incline
Program
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
1
LEVEL
1
LEVEL
2
LEVEL
1
LEVEL
2
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
LEVEL
2
LEVEL
3
LEVEL
2
LEVEL
3
LEVEL
3
LEVEL
1
P11
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P12
(5km)
(10km)
1 2 3 4 5 6 7 8 9 10 11 12
2
3
4
2
3
4
3
4
5
4
5
6
3
4
5
2
3
4
3
4
5
4
5
6
3
4
5
2
3
4
3
4
5
2
3
4
2
3
4
3
4
5
4
5
6
5
6
7
6
7
8
7
8
9
7
8
9
8
9
10
8
9
10
8
9
10
8
9
10
6
7
8
4
5
6
2
3
4
2
3
4
4
5
6
6
7
8
7
8
9
7
8
9
6
7
8
5
6
7
4
5
6
3
4
5
2
3
4
7
8
9
7
8
9
1
2
3
3
4
5
6
7
8
8
9
10
8
9
10
7
8
9
7
8
9
6
7
8
3
4
5
1
2
3
9
10
11
9
10
11
1
2
3
7
8
9
2
2
2
2
3
4
2
3
4
9
10
11
9
10
11
2
2
2
7
8
9
1
2
3
4
5
6
3
4
5
2
3
4
2
3
4
3
4
5
2
3
4
3
4
5
4
5
6
3
4
5
2
3
4
3
4
5
2
3
4
5
6
7
6
7
8
2
3
4
3
4
5
4
5
6
7
8
9
7
8
9
8
9
10
8
9
10
6
7
8
4
5
6
2
3
4
8
9
10
8
9
10
2
3
4
4
5
6
6
7
8
7
8
9
7
8
9
6
7
8
5
6
7
4
5
6
3
4
5
2
3
4
7
8
9
7
8
9
1
2
3
3
4
5
6
7
8
8
9
10
8
9
10
7
8
9
7
8
9
6
7
8
3
4
5
1
2
3
9
10
11
9
10
11
1
2
3
7
8
9
2
2
2
2
3
4
2
3
4
9
10
11
9
10
11
2
2
2
7
8
9
1
2
3
8
9
10
8
9
10
2
3
4
4
5
6
6
7
8
7
8
9
7
8
9
6
7
8
5
6
7
4
5
6
3
4
5
2
3
4
3
4
5
3
4
5
2
3
4
3
4
5
4
5
6
2
3
4
2
3
4
3
4
5
3
4
5
4
5
6
3
4
5
2
3
4
P1 P2 P3 P4 P5
P6 P7 P8 P9 P10 P12
(10km)
P11
(5km)
Speed Program:
Incline Program:
Page 13
situation.
I
12
Page 14
with
wrench # 6
.
right
with wrench # 6
.
30 seconds.
When you feel the noise of running belt is louder,
please use silicone fluid spray on running belt. It is
easy and quick. Before proceeding, ensure the
treadmill power is off and unplugged. Fold up the
treadmill to upright position. Loosen the running
belt and then spray silicone on the inner side of
running belt from both sides. Ensure spray entire
running belt. Please see illustration. After spraying,
please align the running belt and adjust the running
belt tension.
on
13
GAP
GAP
Page 15
Horizontal Adjustment
14
MX800
MX850
MX800
MX800
MX850
1. Please check all cable connection is well connected.
2. The treadmill did not move after pressing "Start" and show E1 , please check if there is any part stuck.
3. The treadmill run for few seconds after pressing "Start" but stops, please check if the sensor
(near flywheel of front roller) is loose or defective.
4. Please check wires connected to motor are loose or not.
5. Please contact stores for service if E1 can not be solved.
When E6/E7 is displayed , remove safety key and insert it again to restart treadmill . If E6/E7 is still shown on
display, please check the following or call for service.
1. Reset incline value
(1) When the position of incline is lower than middle level, press " Mode" and incline "up" buttons. Hold both
buttons and the incline will be raised. Release the two buttons till the incline position is up to middle level.
(2) When the position of incline is higher than middle level, press " Mode" and incline "down" buttons. Hold both
buttons and the incline will be reduced. Release the two buttons till the incline position is down to middle level.
Please try it for few times. If you can not get the incline move, please contact stores for service.
Once the incline position is at middle level, please turn off power and re-start. Please see if E6 / E7 goes away.
If not, please contact stores for service.
2. Please check if red / white incline cables are well connected to MCB.
3. If the above steps can not reset incline , please contact stores for service.
Step1
Step3
Step2
Loading...