Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Table of contents
Introduction ..................................................................................................................................... 2
Symbols used in this Manual ........................................................................................................................ 2
Important Instructions ................................................................................................................................... 2
Note on the Warranty ..................................................................................................................................... 2
Technical Short Information .......................................................................................................... 2
Order Information ........................................................................................................................... 2
Dimensions ..................................................................................................................................... 3
Mounting options ............................................................................................................................ 5
Open the housing ........................................................................................................................... 7
CPU inside ....................................................................................................................................................... 8
Internal Connector List: .................................................................................................................................... 9
Panel Connector List: ..................................................................................................................................... 10
Jumper List: .................................................................................................................................................... 10
Jumper Settings ............................................................................................................................................. 11
BIOS Power Setting ..................................................................................................................................... 12
Panel Connector Pin Assignments ................................................................................................................ 14
Internal Connector Pin Assignment ............................................................................................................... 17
24V-to-12VDC – Converter ............................................................................................................................ 23
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Introduction
Symbols used in this Manual
This symbol point out to especially information.
Important Instructions
This chapter contains instructions which must be observed when using your Flatman Monitor.
The manufacturer’s instructions provide useful information on your device.
Note on the Warranty
Due to their limited service life, parts which by their nature are subject to a particularly high degree of wear
(wearing parts) are excluded from the warranty beyond that provided by law. This applies to the CMOS
battery, for example.
Technical Short Information
Housing Interfaces
RAL 7021 powder coated 4x USB3.0
(WxDxH) 180 x 134 x 68mm (Heatsink included) 3x GbE LAN
Weight: 1300g 2x Display Port
Integrated SBC 2x COM (RS232, RS422, RS485, BIOS configurable)
CPU Intel® Haswell ULT i5-4300U
4GB RAM
Storage: 64GB mSATA SSD
Hardware Monitor Windows7, Windows8, Linux
Voltages, Temperature Environment
Fanless passive cooling
EMC Operating temp.: 0 °-50°C ambient
EN55022 class B Humidity: 10%-90% @ 39°C, non condensing
(option up to 8GB)
Power Consumption UIN IIN PIN
Standby 24 V 0,020 A 0,5 W
Windows IDLE 24 V 0,308 A 7,4 W
Windows typical workload (BurnIn with max. load) 24 V 0,800 A 19,2 W
Windows with CPU at TDP (Thermal Design Power selected in Thermal-analysis-tool) 24 V 0,990 A 23,8 W
Windows with max. workload & max. Graphics adjusted in Thermal-analysis-tool &
turbo mode (max. current consumption) 24 V 1,440 A 34,6 W
Test Setup: Windows 7 pro. 64bit; 4GB RAM ; 60GB mSATA
Order Information
Order# Description
EN00-004001-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 64GB mSATA
EN00-004002-01 RAIL-PC-5101; Intel Haswell i5-4300U, 8GB RAM, 128GB mSATA
EN00-004003-01 RAIL-PC-5101; Intel Haswell i5-4300U, 8GB RAM, 256GB mSATA
EN00-004004-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 32GB mSATA
EN00-004005-01 RAIL-PC-5101; Intel Haswell i5-4300U, 4GB RAM, 128GB mSATA
(option: w/ i7-4650)
16-30VDC Input via Phoenix Connector PSC 1,5/ 3-F
(option: up to ?GB)
Power
OS Support
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Dimensions
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Mounting options
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Always make sure to mount the DIN rail retaining clamp in upper position
The heatsink is flippable according to the Rail PC mounting. Make sure that the airflow always works in
upright direction.
The small milling boundary of the heatsink has to be mounted to the small rim of the Box housing
mounted with two M4x8 (max. length)
counter sunk bolds
Important note: For operating mode has to be inserted a thermal grease between heatsink
and mounting plate
(example for heatsink mounting and airflow:)
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Open the housing
To open the housing just remove five screws:
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Block Diagram
Box PC with Intel® Haswell i5-4300U
CPU inside
1 X LVDS
Connector
2 X Display Port
Connectors
4-DI/4-DO
Wafer
SPI Flash
ROM
4 X USB3.0
Ports
TPM
(optional)
2 X COM
Ports
H/W
Monitor
CHRONTEL
CH7511B
DP
DI/DO
SPI
USB3.0
LPC
Super I/O
Fintek
F81803U
Haswell
ULT
Processors
Audio Codec
Reltek
ALC662
HD
DDR3LLVDS eDP
SATA
USB2.0
PCIE x 1
GbE PHY
Intel I218-LM
Intel I210-AT
GbE Controller
Intel I210-AT
GbE Controller
IN/OUT/MIC
1 X DDR3 SO-DIMM
Sockets
2 X SATA
Connector
1 X USB2.0
PIN Header
1x mPCIE / mSATA
2 X Mini-PCIE
1x mPCIE
Sockets
3 X RJ45
Connectors
Audio
PIN Header
Watch Dog
Timer
Audio AMP
IS31AP2010B
Speaker Out
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
2 X Speaker
Connectors
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Top View:
/ mSATA
Internal Connector List:
Label Function
BAT1 Battery Power Input Wafer
BZ1 Onboard Buzzer
CN1 SATA HDD Power Output Wafer
CN5 USB2.0 Port 4, 5 Pin Header
CN7 Right Channel 3W Audio AMP Output Wafer
CN8 Left Channel 3W Audio AMP Output Wafer
CN9 Audio Pin Header
CN10 Digital Input / Output Pin Header
CN14 P80_Header LPC
CN15 RS-232 / 422 / 485 Port 1 Wafer
CN16 RS-232 / 422 / 485 Port 2 Wafer
CN17 SIM Interface Wafer for MPCIE2
CN18 Backlight Power Output Wafer for LVDS1
DIMM1 DDR3 Memory SO-DIMM Socket
FAN1 CPU FAN Wafer
FP1 Front Panel 1 Pin Header
FP2 Front Panel 2 Pin Header
LVDS1 Primary 24-bit, 2-channel LVDS Panel Connector
mPCIE1 Mini-PCIE Express v1.2 Socket / mSATA
mPCIE2 Mini-PCIE Express v1.2 Socket
SATA1 Serial ATA Port 0 Connector
SATA2 Serial ATA Port 1 Connector
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Panel Connector List:
Label Function
CN2 USB3.0 Port 0,1 Connector
CN3 USB3.0 Port 2,3 Connector
CN11 GbE LAN1 RJ-45 Connector
CN12 GbE LAN2 RJ-45 Connector
CN13 GbE LAN3 RJ-45 Connector
DP1 DP Connector
DP2 DP Connector (Dual Mode)
X1 COM1
X2 COM2
PWR Input Power Connector (3pin Phoenix)
Jumper List:
Label Function
JP1 Panel & Backlight Power Selection for LVDS1
JP2 AT_ATX Mode / MPCIE1 mSATA / mPCIE Selection
JP3 Backlight Power Enable Selection for LVDS1
JP4 MPCIE Activity LED Indication
JP5 USB POWER Selection
JP6 Flash Description Security Over-ride
JP7 RTC Reset Selection
JP8 SRTC Reset Selection
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Jumper Settings
JP1: Panel & Backlight Power Selection for LVDS1 (Pitch 2.54mm)
(not used for Rail-PC-System !!)
21
65
Jumper Setting Status
1
2
1-3 Backlight Power = +12V
3-5 Backlight Power = +5V
2-4 Panel Power = +3.3V
4-6 Panel Power = +5V
JP2: AT_ATX Mode / MPCIE1 mSATA / mPCIE Selection (Pitch 2.54mm)
Jumper Setting Status
1
2
1-3 ATX Mode
3-5 AT Mode (Default)
2-4 mPCIE1 mSATA Selected (Default)
4-6 mPCIE1 mPCIE Selected
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Importent note:
There is no „power-on-button“ on the device available:
Therefore the jumper JP2 (AT/ATX Mode) has always set to „AT-Mode“!
According to this the BIOS setting for Power Mode is „Power Off“!
(Default settings ex factory)
BIOS Power Setting
Control Group Structure Name BIOS Defaults Possible Setting
ACPI Sleep State S3 (Suspend to Ram) Suspend Disabled - S3 (Suspend to Ram)
Restore AC Power LOSS Power OFF Power Off - Power On - Last State
Power Saving Mode Disabled Disabled - Enabled
Resume Event Control
Resume from S3 By PS/2 Keyboard Disabled Disabled - Enabled
Resume from S3 By PS/2 Mouse Disabled Disabled - Enabled
Resume By PCIE Device Disabled Disabled - Enabled
Resume By RingRTC Alarm Disabled Disabled - Enabled
Resume By RTC Alarm Disabled Disabled - Enabled
► WatchDog Timer Configuration
JP3: Backlight Power Enable Selection for LVDS1 (Pitch 2.00mm)
(not used for Rail-PC-System !!)
21
65
Jumper Setting Status
1
2
1-3 Backlight
3-5 Backlight
2-4 Active High
4-6 Active Low
Enable
Enable
JP4: mPCIE Activity LED Indication (Pitch 2.54mm)
(not used for Rail-PC-System !!)
1
2
Pin Description
1 LED+
2 LED-
JP5: USB Power Selection (Pitch 2.00mm)
1
2
3
Jumper Status
1-2 Short USB power will be cut off in S4 & S5 state.
2-3 Short USB power will be cut off in Deep S5 state.
Voltage = +3.3V
Voltage = +5V
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
JP6: Flash Description Security Over-ride (Pitch 2.54mm)
1
2
Jumper Status
1-2 Open Disabled
1-2 Short Enabled
JP7: RTC Reset Selection (Pitch 2.54mm)
1
2
Jumper Status
1-2 Open Normal Operation
1-2 Short Clear RTC CMOS
JP8: SRTC Reset Selection (Pitch 2.54mm)
1
2
Jumper Status
1-2 Open Normal Operation
1-2 Short Clear ME Registers
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Panel Connector Pin Assignments
PWR: Input Power Connector
Pin Signal Mating connector
1
1 GND
2
2 Shield
3
3 VCC
X1: COM1 RS-232/422/485 (via internal cable connection to CN15)
X2: COM2 RS-232/422/485 (via internal cable connection to CN16)
Phoenix Contact
PSC 1,5/ 3-F
Order# 1841909
Pin RS-232 RS-422
1
2
3
4
5
6
7
8
9
DCD Tx- DATA- Tx-
RxD Tx+ DATA+ Tx-
TxD Rx+ - Rx+
DTR Rx- - Rx-
GND GND GND GND
DSR - - -
RTS - - -
CTS - - -
RI - - -
CN2: USB3.0 Port-0,1 Type-A Connector
Pin Signal Name Pin Signal Name
1 +USBA_VCC 10 +USBB_VCC
2 USBA_D- 11 USBB_D3 USBA_D- 12 USBB_D4 GND 13 GND
5 USBA_RX- 14 USBB_RX6 USBA_RX+ 15 USBB_RX+
*：The power source of +USBVCC can be selected by JP5.
7 GND 16 GND
8 USBA_TX- 17 USBB_TX9 USBA_TX+ 18 USBB_TX+
Half Duplex
RS-485
Full Duplex
RS-485
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
left
Box PC with Intel® Haswell i5-4300U
CN3: USB3.0 Port-2,3 Type-A Connector
Pin Signal Name Pin Signal Name
*：The power source of +USBVCC can be selected by JP5.
CN11: GbE LAN1 RJ-45 Connector
CN12: GbE LAN2 RJ-45 Connector
1 +USBA_VCC 10 +USBB_VCC
2 USBA_D- 11 USBB_D3 USBA_D- 12 USBB_D4 GND 13 GND
5 USBA_RX- 14 USBB_RX6 USBA_RX+ 15 USBB_RX+
7 GND 16 GND
8 USBA_TX- 17 USBB_TX9 USBA_TX+ 18 USBB_TX+
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX32 TX1- 6 TX23 TX2+ 7 TX4+
4 TX3+ 8 TX4-
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX32 TX1- 6 TX23 TX2+ 7 TX4+
4 TX3+ 8 TX4-
CN13: GbE LAN2 RJ-45 Connector
Pin Signal Name Pin Signal Name
1 TX1+ 5 TX32 TX1- 6 TX23 TX2+ 7 TX4+
4 TX3+ 8 TX4-
LED Diagram of LAN Connectors:
(front view)
right
left LED: activity / link right LED: 10/100/1000
off No LAN connectivity off 10 Mbit
yellow link green 100 Mbit
blinking activity orange 1 GbE
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
DP1: DisplayPort Port-1 Connector
Pin Signal Pin Signal
1 TX0+ 11 GND
2 GND 12 TX33 TX0- 13 GND
4 TX1+ 14 GND
5 GND 15 AUX+
6 TX1- 16 GND
DP2: Dual Mode DisplayPort Port-2 Connector *
* The Dual-Mode DisplayPort source automatically detects the presence of a plugged-in Dual-Mode DisplayPort cable
adaptor and provides the DVI or HDMI signal, as required, to support the connected DVI or HDMI monitor
7 TX2+ 17 AUX8 GND 18 HPD
9 TX2- 19 GND
10 TX3+ 20 PWR
Pin Signal Pin Signal
1 TX0+ 11 GND
2 GND 12 TX33 TX0- 13 GND
4 TX1+ 14 GND
5 GND 15 AUX+
6 TX1- 16 GND
7 TX2+ 17 AUX8 GND 18 HPD
9 TX2- 19 GND
10 TX3+ 20 PWR
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
Internal Connector Pin Assignment
BAT1: Battery Power Input Wafer
Pin Signal Name
1 +VBAT
2 GND
CN1: SATA HDD Power Output Wafer
1
2
3
4
Pin Signal Name
1 +12V
2 GND
3 GND
4 +5V
CN4: Power Input Wafer (internal cable connection to DC-DC-Converter)
Pin Signal
1 +Vin
2 GND
3 GND
4 +Vin
CN5: USB2.0 Port 10, 11 Pin Header
(not used for Rail-PC-System !!)
1
3
5
2
4
6
87
10
*：The power source of +USBVCC can be selected by JP7
Pin Signal Name Pin Signal Name
1 +USBVCC 2 +USBVCC
3 USB_A- 4 USB_B5 USB_A+ 6 USB_B+
7 GND 8 GND
9 KEY 10 GND
CN7: Right Channel 2W Audio AMP Output Wafer
(not used for Rail-PC-System !!)
Pin Signal Name
1 Speaker+
2 Speaker-
CN8: Left Channel 2W Audio AMP Output Wafer
(not used for Rail-PC-System !!)
Pin Signal Name
1 Speaker+
2 Speaker-
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
CN9: Audio Pin Header
(not used for Rail-PC-System !!)
Pin Signal Name Pin Signal Name
1 2
11
12
CN10: Digital Input / Output Wafer
(not used for Rail-PC-System !!)
CN15 / CN16: RS-232/422/485 Port 1 / 2 Wafer
1 MIC_IN_L 2 MIC_IN_R
3 MIC_IN_JD 4 GND
5 LINE_IN_L 6 LINE_IN_R
7 LINE_IN_JD 8 GND
9 LINE_OUT_L 10 LINE_OUT_R
11 LINE_OUT_JD 12 GND
Pin Signal Name
1 +5V
2 Digital Input 0
3 Digital Output 0
4 Digital Input 1
5 Digital Output 1
6 Digital Input 2
7 Digital Output 2
8 Digital Input 3
9 Digital Output 3
10 GND
CN17: SIM Interface Wafer for MPCIE2
(not used for Rail-PC-System !!)
Pin Signal Name
1 UIM_PWR
2 UIM_DATA
3 UIM_RESET
4 UIM_VPP
5 UIM_CLK
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
6 GND
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
CN18: Backlight Power Output Wafer for LVDS1
(not used for Rail-PC-System !!)
Pin Signal Name
1 BL_ADJ_PWM *
2 BL_ADJ_VOL *
3 GND
4 +5V / +12V **
5 +5V / +12V **
*：BL_ADJ can be setting in BIOS setup.
**：Backlight Power can be selected by JP1.
***：BL_EN can be selected by JP3.
DIMM1: DDR3 Memory SO-DIMM Socket
FAN1: CPU FAN Wafer
6 GND
7 BL_EN***
(not used for Rail-PC-System !!)
Pin Signal
1
2
3
1 GND
2 +12V*
3 FAN_RPM
*：PWM Fan control supported.
FP1: Front Panel 1 Pin Header
RSTBTN
HLED
+
+
7
-
+
21
SPKR
8
-
Note：Internal Buzzer is enabled when Pin6-8 is shorted.
Pin Signal Pin Signal
1 Reset Button + 2 Speaker +
3 Reset Button - 4 NC
5 HDD LED + 6 Internal Speaker7 HDD LED - 8 Speaker -
FP2: Front Panel 2 Pin Header
Pin Signal Pin Signal
1 Power LED + 2 Power Button +
3 NC 4 Power Button 5 Power LED - 6 SMBALERT#
7 BATLOW# 8 SMBus Data
9 GND 10 SMBus Clock
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
LVDS1: Primary 24-bit, 2-channel LVDS Panel Connector
(not used for Rail-PC-System !!)
Pin Signal Name Pin Signal Name
1 LVDS_A0- 16 LVDS_B1+
2 LVDS_A0+ 17 GND
3 LVDS_A1- 18 LVDS_B24 LVDS_A1+ 19 LVDS_B2+
5 LVDS_A2- 20 LVDSBCLK6 LVDS_A2+ 21 LVDS_BCLK+
7 GND 22 LVDS_B3-/NC
8 LVDS_ACLK- 23 LVDS_B3+/NC
9 LVDS_ACLK+ 24 GND
10 LVDS_A3-/NC 25 DDC_DATA
11 LVDS_A3+/NC 26 VDDEN
12 LVDS_B0- 27 DDC_CLK
13 LVDS_B0+ 28 +3.3V / +5V *
*：Panel Power can be selected by JP1.
14 GND 29 +3.3V / +5V *
15 LVDS_B1- 30 +3.3V / +5V *
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
mPCIE1: Mini-PCIE Express v1.2 Socket / mSATA
Signal Pin Pin Signal
WAKE# 1 2 +3.3VSB
Reserved 3 4 Ground
Reserved 5 6 +1.5V
CLKREQ# 7 8 NC
Ground 9 10 NC
REFCLK- 11 12 NC
REFCLK+ 13 14 NC
Ground 15 16 NC
Reserved 17 18 Ground
Reserved 19 20 W_Disable#
Ground 21 22 PERST#
PERn0 23 24 +3.3VSB
PERp0 25 26 Ground
Ground 27 28 +1.5V
Ground 29 30 SMB_CLK
PETn0 31 32 SMB_DATA
PETp0 33 34 Ground
Ground 35 36 USB_DGround 37 38 USB_D+
+3.3VSB 39 40 Ground
+3.3VSB 41 42 LED_WWAN#
Ground 43 44 LED_WLAN#
Reserved 45 46 LED_WPAN#
Reserved 47 48 +1.5V
Reserved 49 50 Ground
Reserved 51 52 +3.3VSB
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
mPCIE2: Mini-PCIE Express v1.2 Socket
Signal Pin Pin Signal
WAKE# 1 2 +3.3VSB
Reserved 3 4 Ground
Reserved 5 6 +1.5V
CLKREQ# 7 8 UIM_PWR*
Ground 9 10 UIM_DATA*
REFCLK- 11 12 UIM_CLK*
REFCLK+ 13 14 UIM_RESET*
Ground 15 16 UIM_VPP*
Reserved 17 18 Ground
Reserved 19 20 W_Disable#
Ground 21 22 PERST#
PERn0 23 24 +3.3VSB
PERp0 25 26 Ground
Ground 27 28 +1.5V
Ground 29 30 SMB_CLK
PETn0 31 32 SMB_DATA
PETp0 33 34 Ground
Ground 35 36 USB_DGround 37 38 USB_D+
+3.3VSB 39 40 Ground
+3.3VSB 41 42 LED_WWAN#
Ground 43 44 LED_WLAN#
Reserved 45 46 LED_WPAN#
Reserved 47 48 +1.5V
Reserved 49 50 Ground
Reserved 51 52 +3.3VSB
*：These pins are connected to CN17 directly.
SATA1: Serial ATA Port 0 Connector
SATA2: Serial ATA Port 1 Connector
Pin Signal Name
1 GND
2 TX+
3 TX4 GND
5 RX6 RX+
7 GND
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Rail-PC-5101
Box PC with Intel® Haswell i5-4300U
24V-to-12VDC – Converter
(Internal usage only)
24VDC Input 12VDC Output
24V
DC
in
Phoenix Contact PSC 1,5/ 3-M
12VDC out
Molex 43650-0403
Pin Signal
1 GND
2 SHLD
3 VCC
Pin Signal
1 +12V
2 GND
3 GND
4 +12V
s&t embedded GmbH – Gutenbergstr. 2 – 85737 Ismaning - Germany
Phone: +49 89 370058 – 0 Fax: +49 89 37000 689
Mail to: info@snt-embedded.de
www.snt-embedded.de V1.1
Loading...