Page 1
USER’S gUIdE
AWF/ACF SERIES
WALL/CEILING AEROCONVECTOR
REPLACEMENT COMPONENT LIST INCLUDED
G
E
I
R
S
-
T
E
É
I
R
F
E
I
D
T
R
Q
E
U
C
A
This unit
complies with
CSA and UL
É
T
I
L
A
U
Q
E
M
È
T
S
Y
S
L
I
T
standards
WARnIng
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this
product.
effective in your region.
The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
This unit must be
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this
.
IMPORTANT INSTRUCTIONS
, according to the
It corresponds to
required capacity to heat a room. If needed, refer to a specialist (industrial and commercial buildings) who will be able to calculate these heat losses and
and to increase your comfort, it is recommended to install several units instead of one. For example, 2 X 1000 W rather than 1 X 2000 W.
Y
S
Y
S
T
E
M
For further information or to consult this guide online, please visit our website at www.stelpro.com
INSAWFACF1115
Page 2
SPECIFICATIONS
WARnIng
indicated in the installation section.
When mounting the unit, make sure that the anchorage used can support the total weight of the unit with the mounting brackets.
When cutting or drilling into a wall or a ceiling, do not damage electrical wiring and other hidden utilities.
Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be
do not let bare skin touch hot surfaces. The unit must cool down for few minutes since it will stay warm for some time after shut-down. Extreme caution is
necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
This unit must be installed at least
at least
from surrounding walls and
heater and away from the side and rear.
Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which could
Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the unit
in accordance with these instructions.
The thermal protection activation indicates that the unit has been subjected to abnormal operating conditions. If the thermal protection remains activated or
damaged. (Refer to the limited warranty)
Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be
repair centre. (Refer to the limited warranty)
Make sure that all the electrical connections have been secured and made properly. Pull each wire to ensure it is not loose in the connector or the terminal
If an option must be added, make sure it has been approved by Stelpro. This way, it will ensure that it has been tested in accordance with our safety rules and
that an appropriate installation has been planned into the unit.
from surrounding walls and
and when using it. To avoid burns,
based on the amount of dirt accumulated on
SAVE THESE INSTRUCTIONS
instances, the instruction manual may not entirely match all the functions of the actual product. Therefore, the actual product and packaging, as well as the name
and illustration, may differ from the manual.
SPECIFICATIONS
UNIT TYPE WATTS VOLTS KG LB
SIMPLE AWF1502 1500 240 20
SIMPLE AWF2002 2000 240 20
SIMPLE 240 20
SIMPLE AWF4002 4000 240 20
SIMPLE AWF4802 4800 240 20
SIMPLE AWF1508 1500 208 20
SIMPLE AWF2008 2000 208 20
SIMPLE 208 20
SIMPLE AWF4008 4000 208 20
SIMPLE AWF4808 4800 208 20
SIMPLE AWF1507 1500 277 20
SIMPLE AWF2007 2000 277 20
SIMPLE 277 20
SIMPLE AWF4007 4000 277 20
SIMPLE AWF4807 4800 277 20
WITHOUT CONTROL
UNIT TYPE WATTS VOLTS KG LB
SIMPLE ACF1502 1500 240 20
SIMPLE ACF2002 2000 240 20
SIMPLE 240 20
SIMPLE ACF4002 4000 240 20
SIMPLE ACF1508 1500 208 20
SIMPLE ACF2008 2000 208 20
SIMPLE 208 20
SIMPLE ACF4008 4000 208 20
SIMPLE ACF1507 1500 277 20
SIMPLE ACF2007 2000 277 20
SIMPLE 277 20
SIMPLE ACF4007 4000 277 20
Add for white, for silica white, for silver or for stainless steel
Add for white, for silica white, for silver or for stainless steel
Several other models with control are available in higher voltages and wattages. For a complete model list, consult our online catalog at www.stelpro.com
2
WITHOUT CONTROL
INSAWFACF1115
Page 3
TECHNICAL DRAWINGS
SIMPLE UNIT
KO
192.4mm
TOP
16 3/8"
415.9mm
127mm
5"
22.2mm
47.8mm
1 1/2"
38.1mm
WALL OR
CEILING
23 1/8"
7 9/16"
587.4mm
7/8"
1 7/8"
WALL OR
TECHNICAL DRAWINGS
3 13/16"
96.3mm
CEILING
2"
51.5mm
K.O. 7/8
(22mm)
1 1/4"
32.5mm
h
K.O. 7/8
(22mm)
h
5"
127mm
14 3/16"
359.6mm
7 9/16"
192.4mm
20 7/16"
519.1mm
FRONT
DOUBLE UNIT
KO
7/8"
22.2mm
WALL OR CEILING
23 1/8"
587.4mm
TRIPLE UNIT
7 9/16"
192.4mm
WALL
5"
127mm
TYP.
11 5/8"
295.9mm
TOP
32 15/16"
836mm
FRONT
7/8"
22.2mm
KO
127mm
TOP
47 3/4"
1212.9mm
TYP.
BACKSIDE
1 9/16"
40.2mm
1 1/2"
38.1mm
3 13/16"
96.3mm
WALL OR CEILING
h
2"
51.5mm
32.5mm
K.O. 7/8
(22mm)
1 1/4"
TYP.
KO 7/8"
22.2mm
11 5/8"
30 13/16"
295.9mm
782.5mm
5"
127mm
TYP.
7 9/16"
192.4mm
20 7/16"
519.1mm
h
SIDE
5"
10 9/16"
269mm
TYP.
1 1/2"
38.1mm
1 9/16"
40.2mm
WALL
3 13/16"
96.3mm
2"
51.5mm
BACK
KO
7/8"
22.2mm
45 5/16"
1151.6mm
10 9/16"
269mm
TYP.
5"
127mm
TYP.
7 9/16"
192.4mm
23 1/8"
587.4mm
FRONT
h
h
SIDE
1 1/4"
32.5mm
TYP.
K.O. 7/8
(22mm)
20 7/16"
519.1mm
BACK
INSAWFACF1115
Page 4
SURFACE
OUVERTURE AU PLAFOND
(pour unité simple)
14 1/4" x 20 5/8"
362mm x 524mm
FLAP
SCREW
SCREW
INSTALLATION
INSTALLATION & OPERATION
adjacent surfaces. Moreover, make sure objects or pieces of furniture such as,
but not limited to, blankets, towels, beds, laundry baskets, clothing, papers,
others, so make sure those near the unit can withstand heat.
surface of the wall or ceiling.
6"
153mm
MIN.
WALL
14 1/2 (368mm) SINGLE
31 1/8 (791mm) DOUBLE
7 1/8"
181mm
MIN.
WALL
WALL
1 1/2"
38mm
20 11/16"
525mm
WARNINGS
1. Recessed and surface installation of AWF units (wall mounting) must
and 2). For ACF units (ceiling mounting), the minimum distance from the
2. Triple units must meet a minimum distance of 12 inches (305 mm) from
surrounding walls and 8 inches (203 mm)
Recessed structure requirement on outside walls for AWF (wall mounting)
and ACF (ceiling mounting) units is the same as for a window structure
(refer to the applicable building codes effective in your area).
4. For surface installation, put a wooden plate at the back of the gypsum in
Use the same dimensions for ceiling application (ACF).
13 1/8"
3 13/16"
96mm
20 7/16"
519mm
333mm
MIN.
WALL
20 11/16"
525mm
45 7/8 (1165mm) TRIPLE
FLOOR
FIG. 1
FRONT
SURFACE INSTALLATION
12"
305mm
12"
305mm
6"
152mm
MIN.
FLOOR
FIG. 2
OPENING
FIG. 5
7 3/8"
187mm
MIN.
6"
152mm
FRAME
INLET
1 3/8"
34mm
FLOOR
FIG. 3
OPENING
TRIPLE UNIT
SCREW
SCREW
SCREW
SCREW
FIG. 6FIG. 4
9 3/8"
238mm
MIN.
FLAP
SCREW
SCREW
FIG. 7
4
INSAWFACF1115
Page 5
1 1/2”
[38 mm]
COUVERCLE ET BOÎTIER DE
SURFACE
INSTALLATION, MAINTENANCE & TROUBLESHOOTING
1 1/2”
FIG. 8
SEE PREVIOUS PAGE FOR WARNINGS
SURFACE INSTALLATION
1. Make sure you use the proper sleeve surface depending on the device
(triple units).
2.
screws.
4. Open the KO to be used and insert the wire with connector.
5. Place the frame against the wall, level and tighten with four (4) wood screws
Replace the inlet, make the required electrical connections. Insert the
OPERATION
[38 mm]
5 5/16”
[135 mm]
WITH FRONT COVER
RECESSED INSTALLATION
1. The opening in the wall must be made in accordance with acceptable
2.
screws.
4. Open the KO to be used and insert the wire with connector.
5.
wood screws (not included) in the left and the right studs, through holes
Replace the inlet, make the required electrical connections and replace
the grille.
MAINTENANCE
Use a soft rag for dusting. When cleaning, use only a damp rag and nonabrasive dish soap. If you use a cleaning product, always wipe the product
used in a very dusty location, use a vacuum brush to remove dust and
other foreign objects from the grilles. If needed, vacuum out the dust inside
the unit. Note that cigarette smoke could yellow the discharge grille and
that the best way to prevent it is to clean the unit on a regular basis.
TROUBLESHOOTING
The circuit breaker is in the OFF position or removed fuse
The unit does not work
The unit runs continuously
The enclosure is extremely hot
The desired ambient temperature can never be reached
Overheating
The unit cycles under control of the thermal protection
(overheat indicator)
The breaker trips when the heater is turned on
N.B. If you do not solve the problem after checking these points, cut off the power supply at the main electrical panel and contact our customer service (see the
“Limited warranty” section to obtain the phone numbers).
Activated thermal protection
Faulty connections
Burned fuse link
Heat losses higher than the unit capacity
Blocked air vents
One or more elements are defective
Voltage lower than that written on the nameplate
Heat losses higher than the unit capacity
Blocked air vents
Faulty connections
Voltage higher than that written on the nameplate
5
INSAWFACF1115
Page 6
REPLACEMENT COMPONENT LIST
REPLACEMENT COMPONENT LIST
1 AWF/ACF
2 AWF/ACF THERMOSTAT BUTTON, WHITE
2 AWF/ACF BOUT-010 THERMOSTAT BUTTON, BLACK
2 AWF/ACF BOUT-011 THERMOSTAT BUTTON, WHITE
AWF/ACF
AWF/ACF
AWF/ACF CONT-5002 CONTACTOR 2P/24V/50A RESISTIVE
AWF/ACF
AWF/ACF
AWF/ACF
4 AWF/ACF ELF-WF1502 ELEMENT ASSEMBLY WF1502
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF ELF-WF1507 ELEMENT ASSEMBLY WF1507
4 AWF/ACF ELF-WF2002 ELEMENT ASSEMBLY WF2002
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF ELF-WF2007 ELEMENT ASSEMBLY WF2007
4 AWF/ACF ELF-WF2008 ELEMENT ASSEMBLY WF2008
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF ELF-WF4002 ELEMENT ASSEMBLY WF4002
4 AWF/ACF
4 AWF/ACF
4 AWF/ACF ELF-WF4007 ELEMENT ASSEMBLY WF4007
4 AWF/ACF ELF-WF4008 ELEMENT ASSEMBLY WF4008
4 AWF/ACF ELF-WF4802 ELEMENT ASSEMBLY WF4802
4 AWF/ACF
4 AWF/ACF ELF-WF4805 ELEMENT ASSEMBLY WF4805
4 AWF/ACF
4 AWF/ACF ELF-WF4807 ELEMENT ASSEMBLY WF4807
4 AWF/ACF ELF-WF4808 ELEMENT ASSEMBLY WF4808
5 AWF/ACF
AWF/ACF THERMAL PROTECTION 1500-2000W
AWF/ACF PROT-007
7
AWF/ACF ST-017
7 AWF/ACF ST-007
7 AWF/ACF
8 AWF/ACF TRANSFORMER 208-240/24/40VA CL.2
8 AWF/ACF TRF700025 TRANSFORMER 277/24/25VA
8 AWF/ACF TRF720025 TRANSFORMER 277/240/25VA
8 AWF/ACF
8 AWF/ACF
8 AWF/ACF TRANSFORMER 240-480/12-24/25VA
8 AWF/ACF TRF520025 TRANSFORMER 480/240/25VA
8 AWF/ACF
8 AWF/ACF
8 AWF/ACF TRF720100 TRANSFORMER 277/240/100VA
8 AWF/ACF TRF520100 TRANSFORMER 480/240/100VA
8 AWF/ACF
AWF* GRILLE WF-1
AWF* GRILLE WF-2
AWF*
ACF* GRILLE CF-1
ACF* GRILLE CF-2
ACF*
10 AWF/ACF
11 AWF/ACF FS-005
11 AWF/ACF FS-024
12 ACF FLK-AWF01
12 AWF FLK-AWF02 FUSE-LINK KIT 1500W-2000W
12 AWF/ACF
AWF/ACF SWI-027
AWF/ACF SWI-028
AWF/ACF
THERMOSTAT SP 120 TO 277V-22A,
THERMOSTAT SP 120 TO 277V-25A,
1500W-2000W (ACF)
Add for white, for silica white, for silver or for stainless steel
8
3
8
11
10
5
7
1
9
2
6
4
13
12
INSAWFACF1115
Page 7
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY
against defects in workmanship and/or materials for the following periods from the date of purchase:
purchaser; it is non-transferable and cannot be extended.
If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1) your
provide the
examine the product itself or any part of it before honoring the warranty. Stelpro reserves the right to
price or
carried out by persons authorized by Stelpro.
Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department at:
. Stelpro reserves the right to examine or to ask one of its representatives to
a defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and
(electricians and distributors - French), (electricians and distributors - English), or
(consumers). The authorization number must be clearly written on the parcel or it will be refused.
This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims
Stelpro’s liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever,
whether based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions
relating thereto. Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages,
services, shutdowns, slowdowns, or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro
This warranty does not cover any damages or failures resulting from: 1) a faulty installation or improper storage; 2) an abusive or abnormal use, lack
disaster or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage,
negligence of the user or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.
The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price,
replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty
period. This warranty will be considered null and void and Stelpro will have the right to refuse any claims if
corrosion or discoloration caused by excessive heat, chemical cleaning products and abrasive agents. It does not cover any damage that occurred
during the shipping.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations
may have other rights which vary from state to state or from province to province.
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
, Stelpro warrants its products and their components
. This warranty applies only to the original
and
the entire unit, its purchase
. Any parts
without
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
7
INSAWFACF1115
Loading...