STEINEL US Oneway COM2-24, US Quattro COM2-24, US Oneway DIM-24, DT Quattro COM2-24, DT Quattro COM1-24 User Manual
...
US Quattro COM1-24
US Quattro COM2-24
US Quattro DIM-24
DT Quattro COM1-24
DT Quattro COM2-24
DT Quattro DIM-24
US Quattro US Oneway
DT Quattro
US Hallway
US Oneway COM1-24
US Oneway COM2-24
US Oneway DIM-24
US Hallway COM1-24
US Hallway COM2-24
US Hallway DIM-24
Information
FR EN
- 2 -
Assembly / Installation / Dimensional Drawings
l
b
a
Load module
Sensor module
Mounts to a 4" Square box, 4" Octagon box or Round 3.0 Mud-Ring
120
US Quattro /
DT Quattro
US Oneway /
US Hallway
120
a
Mounts directly to
ceiling with quick
mount spring tabs
120
120
120
41
36
61
120
61
6
120
Ø min. 68 mm (2 11/16 in)
max. 76 mm (3 in)
120
26
- 3 -
US Quattro COM2-24 / DT Quattro COM2-24 / US Oneway COM2-24 / US Hallway COM2-24
Light level setting
See page 18
Occupancy time
delay setting
See page 18
HVAC
stay-'ON' time
See page 19
HVAC
switch-'ON' delay
See page 19
e f g
d
d
c
h
k
k
Reach setting
See page 19, 20
i
- 4 -
US Quattro DIM-24 / DT Quattro DIM-24 / US Oneway DIM-24 / US Hallway DIM-24
e f m
d
d
k
k
c
Light level setting
See page 18
Occupancy time
delay setting
See page 18
Stay 'ON' time DIM
before 'OFF'
See page 19
Reach setting
See page 19, 20
i
EN
- 5 -
US Quattro COM1-24 / DT Quattro COM1-24 / US Oneway COM1-24 / US Hallway COM1-24
Light level setting
See page 18
Occupancy time
delay setting
See page 18
Reach setting
See page 19, 20
e f i
d
d
c
k
k
EN
- 6 -
L
Disconnect the power supply
before attempting any work
on the sensor!
L
Before installation, make sure
that power has been switched
off at the breaker and check
that the circuit is dead with
a voltage tester.
L
Installing the sensor involves
work on the line voltage power
supply. This work must there
fore be carried out professionally in accordance with the
applicable Nation Electrical
Codes and electrical operating
conditions.
L
Control output DIM-24
(1-10 V) must only be used
for connecting electronic
ballasts with an electrically
isolated 10V dimming
control input.
System Components
a
Load module
b
Sensor module
c
Sensor control plate
d
Sensor DIP switch settings
(1) Normal / Test mode
(2) Manual 'ON' / Automatic
'ON' mode
(3) Momentary / Maintained
switch option
(4) 'ON' only / 'ON'&'OFF'
manual switching
(5) Constant light level DIM
control option
(6)(7)(8)
Trigger mode
(DT Quattro only)
e
Light level setting
f
Occupancy time
delay setting
Switching output 1
g
HVAC stay-'ON' time
Switching output 2
h
HVAC switch-'ON' delay
Switching output 2
i
Reach setting
10.1
COM1-24 Wiring
10.2
COM2-24 Wiring
10.3
COM2-24 Multiple Sensor
Wiring
10.4
DIM-24 Wiring
10.5
DIM-24 Multiple Sensor
Wiring
k
Locking mechanism
l
Assembly / Installation /
Dimensional Drawings
m
Stay 'ON' time DIM before
'OFF' option
n
Trigger mode options
Assembly/Installation (see chart on page 2)
For indoor use only.
Sensor and load modules come
preassembled and must be separated for access to the commissioning settings on the backside
of sensor module by opening the
locking tabs k on the sides.
Reconnect and seat the sensor
to the load module and secure
the locking tabs
k
for normal
operation.
Accessories:
- WGC Wire Guard Cage
- RC 3 Service Remote
- RC 4 User Remote
Operating Instructions
Installer:
This product has been manufactured and 100% quality tested.
Please read all of the instructions
before installation. This will help
you to be familiarized with all the
features and options available to
you with these devices.
This will also assist you to mini
mize installation time and provide
maximum energy savings and
trouble-free operation.
Safety Warnings
l
- 7 -
How it Works / Basic Function
The Control Pro DT Quattro and
Ultrasonic presence detector
product familiy is intended to
control lighting and HVAC in
commercial buildings, schools,
public building, etc.
Lighting is controlled in relation
to both the presence of motion
and ambient light levels. The HVAC
output on the (COM2-24) is
signaled in relation to only the
presence of motion.
Commissioning adjustments
are made by potentiometer or dip
switch settings on the sensor or by
the optional (RC3 service remote)
commissioning tool.
US Quattro COM1-24
DT Quattro COM1-24
US Oneway COM1-24
US Hallway COM1-24
1 switching output (COM1-24 Low
Voltage) operating in relation to
the detection of motion and
ambient light level.
Settings:
- Light level setting
- Occupancy time delay,
Pulse mode, IQ mode
US Quattro COM2-24
DT Quattro COM2-24
US Oneway COM2-24
US Hallway COM2-24
1 low voltage switching output
operating in relation to the
detection of motion and ambient
light level. An additional isolated
normally open and normally
closed set of dry contact closures
for signaling HVAC (heating/venti
lation/airconditioning) in relation
only to the presence of persons.
Settings:
- Light level setting
- Occupancy time delay,
Pulse mode, IQ mode
- HVAC stay-'ON' time
- HVAC switch-'ON' delay,
Auto-HVAC mode
US Quattro DIM-24
DT Quattro DIM-24
US Oneway DIM-24
US Hallway DIM-24
1 low voltage switching output
operating in relation to the
detection of motion and ambient
light level. An additional isolated
1-10 volt dimming output operat
ing in relation to the amount of
daylight present.
Settings:
- Light level setting
- Occupancy time delay, IQ mode
- Stay 'ON' time DIM before 'OFF'
- Constant light level DIM
control option
EN
Loading...