Spannungsprüfer
Combi Check 1.2
Master Check 3.2
D
GB
F
NL
I
E
S
FIN
DK
N
Bedienungsanleitung
Operating instructions
Mode d’emploi
Gebruiksaanwijzing
Istruzioni per l’uso
Instrucciones de manejo
Bruksanvisning
Brugsanvisning
Käyttöohje
Bruksanvisning
C
Konformitätserklärung
Das Produkt erfüllt die
Niederspannungsrichtlinie
73/23/EWG und die EMVRichtlinie 89/336/EWG.
Funktionsgarantie
Dieses STEINEL-Produkt ist
mit größter Sorgfalt hergestellt,
funktions- und sicherheitsgeprüft nach geltenden Vorschriften und anschließend
einer Stichprobenkontrolle
unterzogen.
Die Garantiefrist beträgt
36 Monate und beginnt mit
dem Tag des Verkaufs an den
Verbraucher. Wir beseitigen
Mängel, die auf Material- oder
Fabrikationsfehlern beruhen,
die Garantieleistung erfolgt
durch Instandsetzung oder
Austausch mangelhafter Teile
nach unserer Wahl.
Eine Garantieleistung entfällt
für Schäden an Verschleißteilen, für Schäden und Mängel, die durch unsachgemäße
Behandlung oder Wartung
auftreten sowie für Bruch bei
Sturz.
Weitergehende Folgeschäden
an fremden Gegenständen
sind ausgeschlossen. Die
Garantie wird nur gewährt,
wenn das unzerlegte Gerät mit
Kassenbon oder Rechnung
(Kaufdatum und Händlerstempel), gut verpackt, an die
zutreffende Servicestation eingesandt oder in den ersten
6 Monaten dem Händler übergeben wird.
Reparaturservice:
Nach Ablauf der Garantiezeit
oder Mängeln ohne Garantieanspruch repariert unser
Werkservice. Bitte das
Produkt gut verpackt an die
nächste Servicestation
senden.
8
Zuschaltbare Prüfspitzenbeleuchtung
(nur Combi Check 1.2)
Die Prüfspitzenbeleuchtung
kann manuell durch Drücken
der Taste und einmaliges
Kurzschließen der Prüfspitzen
eingeschaltet werden. Die
Beleuchtung bleibt nur für
die Dauer der Tastenbetätigung eingeschaltet.
Combi Check 1.2
햲 Test probe guard
햳 Test probes
햴 Voltage indicator, LED
햵 Pushbutton
햶 Clip connector
햷 LED's for indicating
쎻
a
DC and AC voltage
쎻b polarity
쎻
c
continuity testing
쎻d phase testing
(Combi Check 1.2
only)
햸 Battery compartment
햹 Accoustic indicator, buz-
zer (Combi Check 1.2
only)
햺 Test probe light
(Combi Check 1.2 only)
Master Check 3.2
햲 Test probe guard
햳 Test probes
햴 Voltage indicator, LED
햵 Pushbutton
햶 Clip connector
햷 LED's for indicating
쎻
a
DC and AC voltage
쎻b polarity
쎻
c
continuity testing
햸 Battery compartment
Dear Customer
Congratulations on purchas-
ing your new STEINEL
Voltage Tester and thank you
for the confidence you have
shown in us. You have chosen a high-quality product
that has been manufactured,
tested and packed with the
greatest care. The step voltage tester is capable of the
following functions:
– DC and AC voltage indica-
tion
– Polarity indication
– Continuity testing with
pushbutton
– Voltage detection > 50 V
AC / 120 V DC even without batteries
– Automatic battery monitor-
ing
– Single-hand operation for
testing socket outlets using
clip connector for test probes
– Phase testing
(Combi Check 1.2 only)
– Visual and accoustic
indicator (Combi Check 1.2
only)
– Selectable test probe light
(Combi Check 1.2 only)
Description
Instructions for Use
GB
9
Technical Specifications
Battery and Function Test
Dimensions: (L x W x H) 230 x 55 x 34 mm
Rated voltage range: Combi Check 1.2: 6–690 V AC/DC
Master Check 3.2: 6–400 V AC/DC
Frequency range: 0–100 Hz;
AC display from f > 2 Hz
Voltage surge proof: Combi Check 1.2: 6 KV
Master Check 3.2: 4 KV
Input resistance: >
300 kOhm
Input current: Combi Check 1.2: Is < 2.5 mA at 690 V
Master Check 3.2: Is < 2.5 mA at 400 V
Continuity testing: Continuity < 500 kOhm
Single-pole phase testing:
Continuity at voltages
(Combi Check 1.2 only)
> 90 V AC (acoustic signal)
Temperature range: – 10 °C to + 55 °C
Battery life: approx. 1500 operations
Battery type: 2 x micro 1.5 V AAA Alkaline
(do not use rechargeable batteries)
Enclosure: IP 50
Approval: to EN 61243-3
= VDE 0682 Part 401
Weight: 135 g
Battery installation:
Open the battery compartment using a screwdriver or
a coin. With the rear side of
the unit facing up, turn the
catch clockwise through 45°
to unlock. Now pull the battery compartment out as far
as the stop. Install batteries
as indicated (do not use
rechargeable batteries). To
close the battery compartment, push the battery compartment as far as it will go
into the housing and lock the
compartment in place by
turning the catch anticlockwise through 45°.
WAR NIN G: Voltage tester
must not be used with the
battery compartment open.
Function test/battery test
With the test probes shorted
and pushbutton pressed the
entire LED step display must
come on briefly, leaving only
the +6 V step indicator on.
An acoustic signal will also
sound. If the +6 V step indicator flashes during this test,
change the batteries at the
next opportunity possible.
The LED step display will
flash while conducting further
voltage/continuity checks to
remind you that the batteries
need changing.
11
Safety Instructions
ç
y
The voltage tester must
only be used within the
specified rated voltage
range. The provisions contained in DIN VDE 0105
Part 100 and EN 50110-1
regarding the use of voltage testers stipulate that
just before testing for isolation from supply, the
voltage tester must be
checked for proper working order. If the indicator
fails to operate during this
check, the voltage tester
must not be used.
y
Indication that the upper
limit for extra-low voltages
(ELV) has been exceeded
only serves as a warning
to the user and not as a
measurement reading.
y
Due to the high input
resistance, the capacitive
and inductive voltages
may be indicated.
y
When testing, hold the
voltage tester by its handles only. Do not touch the
test electrodes. Only perform 2-pole voltage tests.
y
Before using the voltage
tester in places where
noise levels are high,
first check whether the
accoustic test signal is
audible.
y
The LEDs start to glow at
80-85 % of designated
voltage.
y
Reliable indication is only
assured over a temperature range of –10 °C to
+55 °C.
y
The voltage tester must be
checked for proper working order shortly before
and after testing for isolation from supply. If this
check reveals any failure
of the tester to indicate
one or more steps or if the
voltage tester fails to show
that it is ready for operation, it must not be used.
y
The voltage tester and its
accessories must not be
dismantled by unauthorized persons.
y
The tester must be stored
in a dry and clean place.
y
The tester must not be
used in wet conditions
(e.g. condensation or rain)
(IP 50).
y
Within its maximum ON
duration, the device may
be exposed for up to 30
seconds to the maximum
rated voltage of the indicated range.
y
Indicator legibility may be
impaired in adverse light
conditions, e.g. in sunlight.
y
WAR NIN G: Voltage tester
must not be used with the
battery compartment open.
GB
10
Phase testing
(Combi Check 1.2 only)
WAR NIN G: Phase testing
cannot be performed in
unfavourable locations, e.g.
on ladders with wooden
rungs or in rooms with insulated floor coverings and in
AC voltage systems not
properly bonded to earth.
y
To perform the phase test,
contact the small test
probe with the phase
(> 90 V AC) of the AC
voltage system and touch
the phase tester contact
on the indicator handle
with your thumb. The 6 V
step indicator (+ and –)
will light up upon phase
contact and an acoustic
signal is also given.
13
Semiconductor testing
When the button is pressed
during polarity-dependent
continuity testing, the internal
test voltage source is
switched to the test probes.
The display handle represents the positive pole, and
the small handle the negative
pole. If continuity is given, the
+6 V diode illuminates. An
acoustic indication is also
given for Combi Check 1.2.
incorrect correct
Voltage testing
햲 Apply the test probes to
the potential points you
wish to test.
y
For DC voltage testing, the
test probe on the display
handle represents the
positive pole, and the
small test probe the negative pole.
y
The positive and the negative diode of the 6 V voltage step will light up
simultaneously for AC
voltage.
y
The entire LED step display will briefly light up at
the start of each voltage
test.
햳 The level of voltage pre-
sent is indicated by the
LED's lighting up as far as
the step level of voltage
present. An acoustic indication is also given for
Combi Check 1.2.
Continuity testing
햲 Before conducting a con-
tinuity test in electrical
systems, first switch off
external voltage sources
and, where applicable,
discharge capacitors.
햳 Short the test probes and
keep button pressed.
햴 Contact the test object
with the test probes.
Contact the test object
with the test probes. If
contact resistance is
< 500 kOhms, the +6 V
diode will light up.
An acoustic indication is also
given for Combi Check 1.2.
Impressed external voltages
will be indicated despite the
continuity test, and will not
harm the tester.
12
C
Declaration of Conformity
This product complies with
Low Voltage Directive
73/23/EEC and EMC
Directive 89/336/EEC.
Functional Warranty
This STEINEL product has
been manufactured with
great care, and its operation
and safety have been tested
in conformity with the current
regulations. Production is
also submitted to final random-sample testing.
The warranty period is
36 months, starting on the
date of sale to the user. We
undertake to remedy faults
caused by material or manufacturing defects. This warranty undertaking shall be
performed by the repair or
replacement of the defective
parts, at our own discretion.
This warranty shall not cover
damage to wearing parts or
damage and faults caused
by incorrect operation or
maintenance. Breakage due
to a fall is also not covered.
Further consequential damage to external items is excluded.
Claims under warranty shall
only be accepted if the product is sent fully assembled
and well packed complete
with sales slip or invoice
(date of purchase and dealer’s stamp) to the appropriate Service Centre or
handed in to the dealer
within the first 6 months.
Repair Service:
Our Customer Service
Department will repair faults
not covered by warranty or
after the warranty period.
Please send the product well
packed to your nearest
Service Centre.
14
Selectable test probe light
(Combi Check 1.2 only)
The test probe light can be
switched on manually by
pressing the button and
briefly shorting the test probes. The light only remains
on while the button is
pressed.
Combi Check 1.2
햲 Protection des pointes de
test
햳 Pointes de test
햴 Témoin de tension, DEL
햵 Poussoir
햶 Cran
햷 Diodes pour l’affichage
de:
쎻
a
tensions continues et
alternatives
쎻b polarité
쎻
c
test de continuité
쎻d test de phase (uni-
quement Combi
Check 1.2)
햸 Compartiment à piles
햹 Avertisseur sonore
pour signal acoustique
(uniquement Combi
Check 1.2)
햺 Éclairage des pointes de
test (uniquement Combi
Check 1.2)
Master Check 3.2
햲 Protection des pointes de
test
햳 Pointes de test
햴 Témoin de tension, DEL
햵 Poussoir
햶 Cran
햷 Diodes pour l’affichage
de:
쎻
a
tensions continues et
alternatives
쎻b polarité
쎻
c
test de continuité
햸 Compartiment à piles
Cher client,
Nous vous remercions de la
confiance que vous avez
témoignée à STEINEL en
achetant ce testeur de tension. Vous avez choisi un
article de très grande qualité,
fabriqué, testé et conditionné
avec le plus grand soin. Le
testeur de tension vous offre
les fonctions suivantes:
– affichage de tensions con-
tinues et alternatives,
– affichage de la polarité,
– test de continuité avec
poussoir,
– détection de tensions
> 50 V C.A./ 120 V C.C.
même sans piles,
– contrôle automatique des
piles,
– utilisation d’une seule main
pour les tests de prises de
courant par enclenchement
des pointes de test,
– test de phase (uniquement
Combi Check 1.2),)
– affichage visuel et signal
acoustique (uniquement
Combi Check 1.2),
– éclairage débrayable des
pointes de test (uniquement Combi Check 1.2).
Description de l’appareil
Mode d’emploi
F
15
Loading...