STEELMATE LWCLLRCC User Manual
CLCC
BT Long Range
+
-
12.4
12.4
0
-7
00:00
Doors
Unlocked
12.4
User Guide
This button will send a START command to your vehicle
remote starter. The vehicles engine will start and run for the
preset time. The timer will begin to count down from the
preset runtime of the remote starter.
This button will send a STOP command to your vehicles
remote starter. The vehicle's engine will shut down and the
runtime status will change to 00:00:00 once the action has
been completed.
This button will LOCK and/or ARM your vehicle. Your
vehicle MUST be equipped with a power door lock system
for this feature to work. The door lock status will change
once this action is completed.
This button will UNLOCK and/or DISARM your vehicle.
Your vehicle MUST be equipped with a power door locking
system for this feature to work. The door unlock status will
change once this action is completed.
This icon will display the vehicle's battery voltages.
Displays the current temperature inside your vehicle.
read from the antenna.
This button will allow you to access the AUXILIARY
functions. Some of the functions could be Motorized Lift
Gate, Trunk Release, Power Sliding Doors, Rear Defrost,
ETC. See your retailer for more details.
CONFIGURATION MODE
DESCRIPTION
Press and release button. Secures
your vehicle by locking the doors
and arming the factory alarm
Press and release button 2 times
within 2 seconds. Provides the access
to your vehicle by unlocking the doors
and disarming the factory alarm
Press and hold the button for 3 second
(until a long chirp is heard) and
release. This will send the command to
start the engine
Press and hold the button for 3 second
until a long chirp is heard and release
Press and hold for 5 seconds until the
2 quick chirps
Command not received
Transmit command
Quick chirp.1 flash of the green LED
2 quick chirps, 2 flashes
of the green LED
1 short beep, 2 quick chirps, 2 flashes
of the green LED
1 long beep, 3 quick chirps, 3 flashes
of the green LED
1 long beep, 2 long chirps then
2 flashes of the green LED
1 long chirp
Blue LED blinks
x1
x2
3s
3s
5s
_
_
Quick
presses
COMMAND
Lock & Arm
Unlock & Disarm
Start
Extended
runtime
Stop
COMMAND
_
_
For more detailed instructions, please consult the HELP section of the CarLink App.
Micro USB battery
charging port
CLCC
BT Long Range
User Guide
Step 1: App & account setup
Ÿ Search on App Store or Google Play Store for “Car Link”.
Ÿ Download the Car Link smartphone app.
Ÿ Once completed, launch the Car Link app on your device.
Ÿ Click the "Create an Account", fill in the form and create your account.
Ÿ Once done, log into the app using your email address and new secure password.
Step 2: Add a system
Ÿ Click on the (+) sign in the bottom right corner of the Car Link app screen to add your system to your account.
Ÿ Scan the QR Code located on the antenna to add the device in the app.
Ÿ Your device is now linked.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and; (2) This device must
accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates—and can radiate—radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does not cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Ÿ Reorient or relocate the receiving antenna
Ÿ Increase the separation between the equipment and the receiver
Ÿ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Ÿ Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the use's authority to operate the equipment.
LoRa Radio:
Ÿ Operating frequency: 911.85MHz
BLE:
Ÿ Operating frequency: 2402~2480MHz
Battery:
Ÿ Type: Lithium Ion
Ÿ Capacity: 200mAh
Ÿ Voltage: 3.7V
Ÿ Charge Voltage: 5V USB
For terms and conditions, see them under the main menu in the app.
CARLINK CLCC User Guide 201119
Loading...