How it Works
STEELMATE
Loading...
BT4123
Users Manual
16 pgs533.59 Kb0

STEELMATE BT4123 Users Manual

PS03-G3 and PS04-G3
1 WAY REMOTE START SYSTEM
OPERATING INSTRUCTIONS
your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, and Brake Reset. For programming, the hood pin and program button are required.
-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing dealer i.e. Door Locks, Horn-Honk, Anti-Grind, etc. These features may also require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be installed with your particular system.
REV 06-2011
This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any changes or modifications not expressly approved by manufacturer for compliance. Such modification could void the user's authority to operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings…….……………..….…………………………………….…………….….…………2
Using the Remote Transmitter………………………………………………………………………….………....…….3
Status LED……………………………………………………………………………………………….……….……….4 Remote Engine Control…………….…..……………………………………………………………….…….……….4-7 Turbo Timer Mode……………………………….……………………………………...……………….…………….…8 Manual Transmission Mode……………………………….……………………………………...…………………..…9 Convenience and Safety Features……………………………….………………………………….…...……….…9-11
Transmitter Programming….…………….…………………………………………….……………….…………....…12
2 Vehicle Operation.…………………………………….………………...…………………………………….………13 No Factory Keyless Entry after Remote Start…………..…………………………………………………………….14 Remote Start Diagnostics……………………………………………………………………………………………….14 Battery Replacement.…………………………………….………………...……………………..…………….………15 2-Way Data Port…………………………………………………………………………………………………………16
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle linkage, and all engine safety features, are in perfect working condition.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its safety features. B) Check for proper operation of the system prior to accepting delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features. D) Always leave the doors and windows closed and locked to protect against accidents and theft.
DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.
2
USING THE REMOTE TRANSMITTER
VEH
VEH
For PS03-G3
The transmitter supplied with this system has 4 vertical buttons – Lock, Unlock, Start and Vehicle Select. The button configuration is Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate a second vehicle equipped with a PS03-G3 series system.
For PS04-G3
The transmitter supplied with this system has 5 vertical buttons – Lock, Unlock, Trunk Release, Start and Vehicle Select. The button configuration is Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate a second vehicle equipped with a PS04-G3 series system.
3
STATUS LED
STATUS LED: Used for Remote Start Diagnostics – page 14 (Optional, requires Installation of LED)
LED will flash when locking your doors with remote. LED will remain solid in Valet Service Mode.
REMOTE ENGINE CONTROL
REMOTE START & TRUNK POP – Button Press Selection (Option # 6):
To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for button press selection. This option will allow you to change whether the Remote starter and Trunk release activate by a:
1. Double button - ½ second presses.
2. *Single ½ second press (Default).
3. Press and Hold 2 seconds.
*Default = 1 single press & release*
REMOTE ENGINE STARTING – SUCCESSFUL START:
1) Press the remote start button for at least ½ second (*default). Parking lights flash once, return solid, and the Ignition/Acc circuits turn on.
SOLID
FLASH 1X
AFTER
IGN
3
PRESS START
2) After a few seconds the Starter Motor engages. The parking lights and Acc circuits will turn off while cranking.
3) Engine Starts and Runs. Parking Lights and ACC turns back on, and the doors lock.
4) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be turned off with remote transmitter by pressing and releasing the Start button.
THEN
SOLID
4
SEC.
STARTER
REMOTE ENGINE CONTROL
REMOTE ENGINE STARTING – UNSUCCESSFUL START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to 4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to help prevent damage to the starter from over cranking.
1) If engine starts on 2nd or 3rd attempt, see steps 3 & 4 of “Successful Start” on page 4.
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER ATTEMPTS WILL BE MADE AUTOMATICALLY
TURNING OFF A REMOTE STARTED ENGINE:
1) Engine is running in Remote Start (Parking lights ON).
2) Press and release the remote start button or double press (If option #6 is on).
3) Engine & parking lights OFF, Doors re-lock/re-arm.
ENTERING YOUR REMOTE STARTED VEHICLE:
1) With engine running, Unlock system with remote (If equipped) or open door with key.
2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is now controlling your vehicle.
REMOTE START RUN TIME RESET:
The Remote Start Run Time is adjustable from 3 to 30 minute (option # 20). Some local cities have a run time limit for unattended vehicle. You can now reset the engine-run timer to allow for more running time after remote start has already occurred using the remote control. After a successful remote start, press both the Lock & Unlock buttons together for at least 2 seconds. The parking lights will flash 3 times and internal engine timer will reset back to zero minutes.
LOCK with REMOTE START and After REMOTE START ABORT:
Option # 8 controls whether the system will automatically lock during and after a remote Start abort or time-out. This feature can be turned OFF. The default is Lock with Remote Start.
5
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use