STEELMATE BT1011A User Manual
RS1-G5, RS3-G5, RS4-G5
RS7-G5
(2-Way Paging System)
REMOTE START SYSTEM
OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP
Technology by Crimestopper Security Products Inc. This booklet contains the information necessaryforoperating
your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
The RS1-G5, RS3-G5 & RS4-G5 system comes with (2) 1-way AM remotes
The RS7-G5 FM system comes with a 2-Way LCD Pager and a 1-Way FM remote.
OPTIONA
i.e. Door Locks, Trunk Pop, Dome LightIllumination,Horn-Honk,Anti-Grind,etc. Thesefeaturesmayalsorequire
additional parts and/or laborfees. Consult withyourinstallerbeforehandto be sureof what is going to beinstalled
with your particular system.
L Features a
REV 7.13.15
re to beconnectedonlyif desired or agreedupon by the customer and the installing dealer
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equi
pment.
TABLE OF CONTENTS
Operation Cautions & Warnings…….……………..….………………………………….…………….….…………2
Using the Remote Control (1, 4 and 5 button)….……………….……………………….………....………….....3-4
Using the 2-Way Pager……………………………………………….……………………….………....…………...5-6
Setting the Clock and Beep or Vibrate Selection…………………………………………………….……….….6-7
Status LED………………………………………………………………………………………………..……….….……8
Remote Engine Control…………….…..……………………………………………………………….…….…..…8-11
Turbo Timer Mode……………………………….……………………………………...……………….…………..….12
Manual Transmission Mode……………………………….……………………………………...…………………..13
Convenience and Safety Features……………………………….………………………………….…...……....14-15
Transmitter Programming….…………….…………………………………………….……………….…………16-17
2 Vehicle Operation.…………………………………….………………...…………………………………….………18
No Factory Keyless Entry after Remote Start…………..………………………………………………………….19
Remote Start Diagnostics……………………………………………………………………………………………..19
2-Way Data Port and Smart Phone Data Port………………………………………………………………………20
Remote Battery Replacement (1, 4 and 5 button remote)……...…………………..…………….………….21-23
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting
from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which
all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle
linkage, and all engine safety features, are in perfect working condition.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system
and its safety features. B) Check for proper operation of the system prior to accepting delivery of the vehicle from
the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper
operation of this system and its safety features. D) Always leave the doors and windows closed and locked to
protect against accidents and theft.
DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide
fumes
2
USING THE REMOTE CONTROL
VEH
RS1-G5 RS3-G5
RS1-G5: The transmitter supplied with this system is a single button remote control.
RS3-G5: The transmitter supplied with this system has 4 vertical buttons – Lock, Unlock, Vehicle Select and Start.
To eliminate the possibility of accidentally starting the vehicle, there are (3) choices for button press selection.
Option # 6 will allow you to change whether the Remote Starter is activated by a:
1. Double Press – 2 presses of Start button.
2. *Single ½ second press (Default).
3. Press and Hold Start button 2 seconds.
*Default = 1 single press Start*
Please consult your installer to change programmable options
3
USING THE 5 BUTTON REMOTE CONTROL
FM 1-WAY
VEH 1 = Green LED
VEH 2 = Red LED
AUX Outputs thru Data
AUX 1 = Trunk + Lock
AUX 2 = Trunk + Unlock
AUX 3 = Trunk + Start
AUX 4 = Lock + Start
(Requires Canbus Data Module)
ARM /
LOCK
TRUNK
VEH
AM 1-WAY
VEH 1 = Blue LED
VEH 2 = Red LED
DISARM /
UNLOCK
START
VEHICLE
SELECT
REMOTE VALET = LOCK + UNLOCK (4 seconds)
Option 27 has 3 choices for Remote Valet.
1. Double Press.
2. 4 Second Press (Default).
3. OFF (no Remote Valet).
NOTE: The VEH button can be used to keep remote control from accidentally operating your vehicle..
4
USING THE 2-WAY PAGER TRANSMITTER
Valet Mode
(Tools)
Transmit Signal
Ignition ON
Lock/Unlock
(Arm/Disarm)
Silent no beeps
CLOCK /
Run Count Down
LOCK / ARM
USB Charger
(Under Side Cover)
Note:
Some Icons on the LCD display only function
on the Combo Alarm with Remote Start
POWER OFF FUNCTION
To turn Power ON, press and hold unlock button 2 seconds.
To turn Power OFF, press and hold unlock button 5 seconds.
LCD SCREEN ICONS
Battery Life
Hood Open
Sensor Warning
(Small Hammer)
Sensor Trigger
(Big Hammer)
Door Open
Trunk Open
Remote Started
UNLOCK / DISARM
5
SIDE BUTTONS
TRUNK
RELEASE
VEHICLE
SELECT
REMOTE
START
AUX Outputs thru Data
AUX 1 = Trunk + Lock
AUX 2 = Trunk + Unlock
AUX 3 = Trunk + Start
AUX 4 = Lock + Start
This remote can control up to 4 AUX
functions thru data depending on the
vehicle and data module. This is typically
used for operating left and right sliding
doors. (Requires Canbus Data Module)
USING THE 2-WAY PAGER TRANSMITTER
The 2-Way LCD Pager remote transceiver is used to send and receive information from the vehicle. The
Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your
range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed to
page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels of
electronic interference. Handle the pager/remote with care. The LCD display and/or the electronics may be
damaged if subjected to abuse.
BATTERY CHARGING
The 2-Way LCD remote has a battery charge indicator on top right corner of display. The battery voltage affects the
distance of the remote control. The system comes with a standard Mini USB charging cable that plugs into the side
of remote control. To access to USB plug, slide the cover to the left shown below.
SETTING THE CLOCK (2-WAY- LCD REMOTE)
1. Press VEH Button on the side of the remote control 5 times.
2. The remote will beep and the AM or PM display will begin flashing.
3. Press the Trunk Button to go to the next item – AM - PM - Hour- Minutes.
4. Press the Lock Button to Increase time.
5. Press the Unlock Button to decrease time.
6. Press the Start Button to Disable or Enable Beep and Vibration. See next page.
7. Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
6
USB Charging Port
REMOTE BEEP & VIBRATE SELECTION
The LCD pager remote BEEPS and VIBRATES when it receives a signal from the vehicle. The Beeps and
Vibration are selectable (on/off). To enter program mode,
1. Press VEH Button on the side of the remote control 5 times.
2. The remote will beep and the AM or PM display will begin flashing.
3. Press the Start button to choose the mode of “Beep ON/OFF & Vibrate ON/OFF”.
4. Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
Mode 1: Beep ON & Vibrate ON. Remote Start Run Time Reminder Beep ON & Vibrate ON.
Mode 2: Beep ON & Vibrate OFF. Remote Start Run Time Reminder Beep ON & Vibrate OFF.
Mode 3: Beep OFF & Vibrate ON. Remote Start Run Time Reminder Beep OFF & Vibrate ON.
Mode 4: Beep OFF & Vibrate OFF. Remote Start Run Time Reminder Beep OFF & Vibrate OFF.
Mode 5: Beep ON & Vibrate OFF. Remote Start Run Time Reminder Beep OFF & Vibrate OFF.
Mode 6: Beep OFF & Vibrate ON. Remote Start Run Time Reminder Beep OFF & Vibrate OFF.
7
STATUS LED
LED Operation: (Optional, requires Installation of LED)
LED will flash when locking your doors with remote.
LED will remain solid in Valet Service Mode.
REMOTE ENGINE CONTROL
REMOTE START Button Press Selection (Option # 6):
To eliminate the possibility of accidentally starting the vehicle, there are (3) options for button press selection. This
option allows you to change whether the Remote starter is activated by a:
4. Double button - ½ second presses.
5. *Single ½ second press (Default).
6. Press and Hold 2 seconds.
*Default = 1 single press*
REMOTE ENGINE STARTING - SUCCESSFUL START:
1) Press the remote start button for at least 1/2 second (*default). Parking lights flash once, return solid, and the
Ignition/Acc circuits turn on.
SOLID
FLASH 1X
AFTER
IGN
3
PRESS START
2) After a few seconds the Starter Motor engages. The parking lights and Acc circuits will turn off while cranking.
3) Engine Starts and Runs. Parking Lights and Acc turns back on, and the doors lock.
4) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be
turned off with remote transmitter by pressing and releasing the Start button.
Note: When the vehicle remote starts, the 2-Way Pager will display the engine run in place of the Clock.
THEN
SOLID
8
SEC.
STARTER
Loading...