STEELMATE BT1011 Users Manual

RS1-G3

ONE BUTTON REMOTE START SYSTEM

OPERATING INSTRUCTIONS

CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP
Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating

your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote

Start connections, Flashing lights, and Brake Reset. For programming, the program button must be installed.

-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing
dealer i.e. Door Locks, Horn-Honk, Anti-Grind, etc. These features may also require additional parts and/or labor
fees. Consult with your installer beforehand to be sure of what is going to be installed with your particular system.

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV 08.15.2011

This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any changes or modifications not expressly
approved by manufacturer for compliance. Such modification
could void the user's authority to operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings…….……………..….…………………………………….…………….….…………2

Using the Remote Transmitter………………………………………………………………………….………....…….3

Status LED……………………………………………………………………………………………….……….……….4
Remote Engine Control…………….…..……………………………………………………………….…….……….4-7
Turbo Timer Mode……………………………….……………………………………...……………….……………..…8
Manual Transmission Mode……………………………….……………………………………...…………………..…9
Convenience and Safety Features……………………………….………………………………….…...………..10-11

Transmitter Programming….…………….…………………………………………….……………….…………....…12

No Factory Keyless Entry after Remote Start…………..…………………………………………………………….13
Remote Start Diagnostics……………………………………………………………………………………………….13
Battery Replacement.…………………………………….………………...……………………..…………….………14
2-Way Data Port…………………………………………………………………………………………………………15

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting
from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which
all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle
linkage, and all engine safety features, are in perfect working condition.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system
and its safety features. B) Check for proper operation of the system prior to accepting delivery of the vehicle from
the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper
operation of this system and its safety features. D) Always leave the doors and windows closed and locked to
protect against accidents and theft.

DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide
fumes.

2

USING THE REMOTE TRANSMITTER

REMOTE START BUTTON PRESS SELECTION (Option # 6):

The transmitter supplied with this system is a single button remote control.
To eliminate the possibility of accidentally starting the vehicle, there are (3) options for button press selection. This
option will allow you to change whether the Remote Starter is activated by a:

1. Double Button - ½ second presses.

2. *Single ½ second press (Default).

3. Press and Hold 2 seconds.

*Default = 1 single press*
Please consult your installer to change programmable options

3

STATUS LED

VEHICLE STATUS LED : Used for Remote Start Diagnostics – page 13 (Install optional)

The optional LED will remain solid when the system is in Valet Service mode. The remote start function WILL
NOT operate when in Valet Mode. See page # 10 for Valet Mode.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING - SUCCESSFUL START:

1) Press the remote start button for at least 1/2 second (*default). Parking lights flash once, return solid, and the
Ignition/Acc circuits turn on.

2) After a few seconds the Starter Motor engages. The parking lights and Acc circuits will turn off while cranking.

3) Engine Starts and Runs. Parking Lights and Acc turns back on, and the doors lock.

4) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be
turned off with remote transmitter by pressing and releasing the Start button.

SOLID

FLASH 1X

AFTER

IGN

4

THEN

SOLID

4

SEC.

STARTER

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING - UNSUCCESSFUL START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of
up to 4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to
help prevent damage to the starter from over cranking.

1) If engine starts on 2nd or 3rd attempt, see steps 3 & 4 of "Successful Start" on page 4.

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY

TURNING OFF A REMOTE STARTED ENGINE:

1) Engine is running in Remote Start (Parking lights ON).

2) Press and release the remote start button or double press (If option #6 is on).

3) Engine & parking lights OFF, Doors re-lock.

ENTERING YOUR REMOTE STARTED VEHICLE:

1) With engine running, Unlock system with remote (If equipped) or open door with key.

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.

4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is
now controlling your vehicle.

REMOTE START RUN TIME RESET:

The Remote Start Run Time is adjustable from 3 to 30 minutes (option # 20). Some local cities have a run time
limit for unattended vehicle. You can now reset the engine-run timer to allow for more running time after remote
start has already occurred using the remote control. After a successful remote start, press both the Lock &
Unlock buttons together for at least 2 seconds (requires 3 or 4 button remote). The parking lights will flash 3
times and internal engine timer will reset back to zero minutes.

5