Steel-Line SD800 Installation And Operating Instructions Manual
SD800
Sectional Garage Door Opener
Installation and Operating Instructions
THIS MANUAL CONTAINS IMPORTANT SAFETY INFORMATION
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THIS MANUAL THOROUGHLY
SD800- Sectional Garage Door Opener
Page 1
Installation & Operating Instructions
User Information……………………………………………………………………………... 1
Important Safety Instructions……………………………………………………………. 2
Package Contents……………………………………………………………………………. 3
Rail Details………..……………………………………………………………………………. 3
Assembly & Installation……………………………………………………………………. 4-8
Interface………………………………………………………………………………………… 9
Programming Instructions………………………………………………………………… 10-13
Technical Specifications………………..…………………………………………………… 14
Troubleshooting………………………………………………………………………………. 15
Warranty……………………………………………………………………………………....... 16
User Information
Important Safety Notes:
A garage door is the largest automated moving object in most homes.
Care needs to be taken when using this system.
Like any other electrical appliance or machine it is important to familiarise yourself with the safety guidelines
which are applicable to automated garage doors. These are contained at the beginning and throughout this
booklet.
The following summary highlights some of these safety guidelines:
Only operate the garage door when in full view to ensure people, objects and pets remain away from the door
whilst it is moving.
Keep all controls away from children and do not allow them to play with the door.
Regularly check the door and have it maintained and serviced as per the manufacturers’ instructions.
Safety beams or an equivalent safety device are recommended for any automated door for additional safety.
Standard Operation of the Door:
When the programmed remote transmitter (handset) button is pressed it will start the door moving.
The next press of the button will stop the door.
The next press will start the door moving in the opposite direction.
Installation Details:
Installation Date:
Installed by:
Telephone Number:
Contents
SD800 – Sectional Garage Door Opener
Page 2
Installation & Operating Instructions
Important Safety Instructions
FAILURE TO COMPLY WITH THESE SAFETY RECOMMENDATIONS AND LOCAL
SAFETY REGULATIONS MAY RESULT IN SERIOUS INJURY, DEATH OR DAMAGE
TO PROPERTY.
PLEASE READ CAREFULLY AND ENSURE THAT ALL SAFETY RECOMMENDATIONS AND
REGULATIONS ARE CONSIDERED AND ADHERED TO.
This appliance is not intended for use by children or persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a
person responsible for their safety.
Do not wear watches, rings or loose clothing while installing or servicing a garage door opener. Ensure that
gloves, safety goggles and suitable protective clothing is worn where appropriate.
The opener must not be installed in a wet or damp space exposed to weather.
Keep garage door balanced. Do not let the opener compensate for a binding or sticking garage door. Binding,
sticking or unbalanced doors must be repaired before installing this opener.
To avoid serious personal injury from entanglement, remove all ropes, chains and locks connected to the garage
door before installing the door opener.
Installation and wiring must be in accordance with your local building and electrical codes.
Install the wireless remote control (transmitter) in a location where the garage door is visible, at a height of no
less than 1.5m and out of reach of children. Do not allow children to operate push buttons or transmitters.
Serious personal injury from a closing garage door may result from misuse of the opener.
Permanently fasten the Warning Labels in prominent places, adjacent to wall controls and on manual release
cord as a reminder of safe operating procedures.
Use the manual release only for the separation of the carriage from the drive and, if possible, only when the
door is in the closed position. Do not use the release cord or carriage to push the door up or pull it down.
Operation of the manual release can lead to uncontrolled movements of the door if springs are weak or
damaged, or if the door is unbalanced. The release handle should be installed at a height less than 1.8m from
the floor.
Ensure that the safety reverse system is tested every month. The garage door must reverse on contact with a
50mm high object placed on the floor. Adjust if necessary and repeat test. Failure to adjust properly may result
in serious personal injury from a closing garage door.
Disconnect electric power to the door opener before making repairs.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid hazard.
Frequently examine the door installation paying particular attention to the cables, springs and mountings for
signs of wear, damage or imbalance. Springs and hardware are under extreme tension and a fault can cause
serious personal injury. Do not use if repair or adjustment is needed.
Ensure that the opener is operated only when door is in full view, free of obstructions and the opener is
properly adjusted. No one should enter or leave the garage while the door is in motion.
Do not allow children to play near the door, or with door controls. Keep remotes away from children.
The door may operate unexpectedly, therefore do not allow anything to stay in the path of the door.
SAVE THESE INSTRUCTIONS- it is important for the safety of persons to follow all instructions.
SD800- Sectional Garage Door Opener
Page 3
Installation & Operating Instructions
Package Contents
Garage Door Opener:
Rail Details
One Piece Belt Rail
DOOR HEIGHT RAIL LENGTH CEILING FIXING POINT OVERALL LENGTH
Up to 2500mm
3300mm
300
0mm
333
0mm
10 13 12 11
9
8
7
4
6
5
3 2
1
(1
) SD800 opener/powerhead
(2) Hand transmitter (3)
(3) Door bracket
(4) Lintel/Ceiling bracket
(5) Curved door arm
(6) Straight arm
(7) Fixing bracket
(8) Hanging bracket (2)
(9) Rail bracket (2)
(10) Hardware bag
(11) Door safety label
(12) Manual release instruction card
(13) Installation & product manual
(14) Rail trolley assembly
14
SD800 – Sectional Garage Door Opener
Page 4
Installation & Operating Instructions
Assembly & Installation
STEP 1. RAIL & TROLLEY ASSEMBLY
Remove packing materials from the rail and remove trolley assembly parts from the bag. Insert steel keeper with
spring into the trolley carriage.
Using the four screws provided fix the trolley to the section already installed in the rail.
Using the split pin connect the keeper to the engagement lever. Tie manual release cord/knob to the release
lever on the trolley, ensuring that the manual release instruction card is attached.
SD800- Sectional Garage Door Opener
Page 5
Installation & Operating Instructions
STEP 2.
Attach straight arm (6) to the trolley assembly with the clevis pin (10) and R-clip (10).
Slide fixing bracket onto rail at the drive end.
STEP 3.
Adjust the belt tension by adjusting the nut located at the end of the rail assembly. Always ensure that the trolley
mechanism is disengaged before adjusting the belt tension. Turn clockwise to tighten and counterclockwise to
loosen. Tighten until you remove all of the slack in the belt. Do not overtighten but ensure belt is firm.
STEP 4.
Insert drive cog (10) onto powerhead (1) shaft. Align rail and powerhead and slide rail over drive shaft. Secure the
rail over the opener using the two rail brackets (9) and the hex flange nuts.
STEP 5.
Install the lintel/ceiling bracket (4). You can attach the lintel bracket either to the lintel above the door (head) or
the ceiling. With the door closed, mark the centerline of the door extended onto lintel wall above door with a
vertical line. Open door to highest point and draw an intersecting horizontal line on lintel wall at least 50mm above
high point to allow for clearance for top edge of the door. Fix lintel bracket into position using the screws provided.
PARTS REQUIRED
(6)
(10)
(10)
PARTS REQUIRED
(1) (9)
(10)
PARTS REQUIRED
(4)
Loading...