Steelkor AC-SP User Manual
SUGGESTED SPECIFICATIONS FOR CONVEYOR
MODEL AC-SP
Soiled Dish Accumulator Conveyor to be
Mfg Co., model ACSP, UL and ETL Listed, and NSF approved commercial kitchen conveyor.
Dual Conveyor Belts to be low friction acetal slats, 10" wide Slats joined with stainless steel pin
connectors. Belt to operate at a variable speed of 5 to 40 feet per minute.
Conveyor Bed to be constructed on #14 gauge, 300 series stainless steel with 3” high x 1-1/4” wide
rolled rim on exposed sides and 10” high x 2-1/2” wide splash along walls. Polish stainless steel to a #3
finish. Belt channel to be fully enclosed and fitted with full length UHMWP wears strips. Belt returned
via flanged non-friction PVC roller assemblies.
Drive Housing to be a welded stainless steel frame with hinged, lift off, double wall, #16 gauge
stainless steel access door exposing oversized, removable stainless steel scrap pan. Drive housing to be
supported by four 1-5/8" O.D., #16 gauge stainless steel legs and stainless steel adjustable bullet feet.
Drive Type to be 90-volt DC, ½ H.P. variable speed with 120volt-60 cycle service, internal torque
limit adjustment and ramp acceleration start. Controlled by one (1) on/off switch station and variable
speed control.
Drive end of conveyor furnished with concealed anti-jam Silver Saver switch plate to prevent foreign
material from jamming drive system.
Automatic Wash System to be provided with 1-1/2” drain and strainer at drive housing and fulllength, adjustable height, stainless steel drip pan. Wash system incorporates; mixing and check valves,
brass spray nozzles and an adjustable detergent injector. Hot water and detergent continuously rinse
and lubricate both sides of the belt.
SOUTHERN ENGINEERING SYSTEMS by Duke
Conveyor supported by 1-5/8” 16gauge stainless steel tubing Legs with welded stainless steel cross
rails. Leg frames fitted into enclosed, round stainless steel gussets welded to stainless steel channel
braces and fitted with stainless steel adjustable bullet feet.
Conveyor to be pre-wired and factory tested.
Conveyor to carry UL and ETL listing and shall be NSF approved.
All equipment built in an ISO
9001:2000 approved manufacturing facility
.
2305 N. Broadway
St. Louis, MO 63012
BY
"Your Sol utions Partner "
Fax 314-231-5074
www.dukemfg.com
5/07
Ph 314-231-1130
Optional Accessories
12” Slat-Pin Belt Sloped Rack Shelf – Wall Mount
Flanged Feet Sloped Rack Shelf – Cantilevered
SS Window Frame & Sill Flat Storage Shelf - Wall Mount
Removable Skirting Panels – SS Flat Storage Shelf - Cantilevered
Removable Skirting Panels - Laminate Stationary Under Shelf
Sight & Sound Barrier Removable Under Shelf
Security or Fire Door 3” High x 1-1/2” Channel Rim Sides
Prison Security Package 7/8” High x 1-1/4” Marine Edge
Additional Start-Stop Station 90 Degree Turn
Foot Switch (Momentary Stop) Special Turn
Hip Switch (Constant Stop) Pre-Rinse Sink
Limit Switch – Bed Mount Disposer Sink
Limit Switch – Splash Mount Scrapping Trough
Flush-Wash (Drip pan and Drains only.) Trough Wheels
Power Tray Discharge (Drive End) Recessed SS Roller Section
Tray Storage Platform (Tail End) Removable Skirting Panels
Other ____________________________ Pre-Rinse Spray – Splash Mount
____________________________ Pre-Rinse Spray – Bed Mount.
Design Option (Pick One)
32” Long Drive Housing (Standard)
40” Long Drive Housing (Optional)
COMMENTS/NOTES ____________________________________________________________
14GA SS FLAT STORAGE SHELF W/
ADJ 14GA SS SLEEVED BRACKETS
& 16GA SS TUBING SUPPORTS
14GA SS SLOPED RACK SHELF W/
ADJ 14GA SS SLEEVED BRACKETS
& 16GA SS TUBING SUPPORTS
31-1/4"
27-1/2"
10"
BELT BELT
2 1/2"
10"
ADJ SS DRIP PAN
16GA SS LEGS WITH
ADJ SS BULLET FEET
1 1/4"
2 1/2"
10"10"
10"
3"
2'-10" A.F.F.
BELTBELT
2'-10" A.F.F. 10"
REMOVABLE 16GA SS
ENCLOSURE PANELS
1 1/4"
3"
2'-10" A.F.F.
Loading...