Steele SP-PB113 Owner’s Manual
Owner's Manual
Owner's Hanua|
GENERAL SAFETY RULES
O" aW
..... _ Must R_nstructi0nMan uaL
SP-PBI 13 Fn.sERv=_:
I _ WaRNING! Read and understand all the instructi°ns bef°re attempting t° as- 1
semble or operate the toot. Failure to follow the instructions listed below could
result in electric shock, fire and/or serious personal injud/
SAVE THESE INSTRUCTIONS.
WORK AREA
1. KEEP YOUR WORK AREA CLEAN AND WELL LIT. Cluttered benches and dark
2. DO NOT OPERATE POWERTOOLS IN EXPLOSIVE ENVIRONMENTS, SUCH
3. KEEP BYSTANDERS, CHILDREN ANDWSITORS AWAYWHILE OPERATING
4. STORE IDLE TOOLS OUT OF THE REACH OF CHILDREN AND OTHER UN-
5. NEVER LEAVETHETOOL RUNNING UNATTENDED.TURNTHE POWER OFR
5. MAKE THE WORKSHOP CHILBPROOF - with padlocks, master switches, or by
ELECTRICAL SAFETY
1. BEFORE PLUGGING INTHETOOL, BE CERTAINTHE OUTLETVOLTAGE
2. GROUNDING TOOLS ARE EQUIPPED WITH THREE-PRONG PLUG (THE
3. AVOID BODY CONTACTWITH GROUNDED SURFACES SUCH AS PIPES,
4. DO NOT EXPOSE POWER TOOLS TO RAIN OR WET CONDITIONS. Water
5. DO NOT ABUSE THE CORD. Never use the cord to carry the loci or pull the plug
5. WHEN OPERATING A POWER TOOL OUTSIDE, USE AN OUTDOOR EXTEN-
Refer to them often and use them to instruct others
areas invite accidents DO NOT leave tools or pieces of wood on the saw while it
is in operation
AS INTHE PRESENCE OF FLAMMABLE LIQUIDS, GASES OR DUST. Power
tools create sparks, which could ignite dust or fumes
A POWER TOOL. Distractions could cause you to lose control.
TRAINED PERSONS. Tools are dangerous in the hands of untrained users
Don't leave the tool until it comes to a complete stop.
removing starter keys.
SUPPLIED iS COMPATIBLE WlTHTHE VOLTAGE MARKED ONTHE NAME-
PLATE WITHIN 10%. An outlet voltage incompatible with that specified on the
nameplate carl result in serious hazards and damage to the tool.
GROUNDING BLADE ISTHE LONGEST OFTHE 3 BLADES). This plug will fit
into a three-hole electrical receptacle• Do not modify the plug provided. If the plug
does not fit the outlet, have the proper outlet installed by a qualified electrician.
Check with a qualified electrician or service personnel if the grounding instruc-
tions are not completely understood, or if in doubt as to whether the tool is
properly grounded
RADIATORS, RANGES AND REFRIGERATORS. There is an increased risk of
electric shock if your body is grounded
entering a power tool will increase the risk of electric shock.
from an outlet. Keep the cord away from heat. oil. sharp edges or moving parts
Replace damaged cords immediately Damaged cords increase the risk of electric
shock
SION CORD MARKED "W-A" OR "W". These cords are rated for outdoor use
and reduce the risk of electric shock.
GENERAL SAFETY RULES
PERSONAL SAFETY
1. STAY ALERT. Watch what you are doing and use common sense when operating
a power tool Do not use a tool while tired or under the influence of drugs, alcohol
or medication A lack of attention while operating power tools could result in seri-
ous personal injury,
2. DRESS PROPERLY. Do not wear loose clothing or jewelry, Keep your hair, cloth-
ing and gloves away from moving parts, Loose clothes, jewelry, or long hair could
get caught in moving parts. Roll long sleeves above the elbow. Rubber gloves and
non-skid footwear are recommended when working outdoors
3. AVOID ACCIDENTAL STARTING. Make sure the switch is "OFF" before plugging
in Carrying tools with your finger on the switch or plugging in tools that have the
switch "ON" invites accidents
4. REMOVE ADJUSTING KEYS OR WRENCHES BEFORE TURNING ON THE
TOOL. A wrench or a key that is left attached to a rotating part of the tool could
result in personal injury
5. DO NOT OVERREACH. Keep proper footing and balance at all times, Proper
footing and balance enables better control of the tool in unexpected situations,
0. DO NOT STAND ON TOOL OR ITS STAND. Serious injury may occur if the tool
is tipped or if the cutting tool is accidentally contacted Do not store materials on
or near the tool such that is necessary to stand on the tool or its stand to reach
them,
7. USE SAFETY EQUIPMENT. ALWAYSWEAR EYE PROTECTION. Dust masks,
safety shoes, hard hat or hearing protection must be used for appropriate condi-
tions Everyday eyeglasses only have impact resistant lenses, they are NOT
safety glasses, These safety glasses must conform to ANSI Z87,1 requirements,
NOTE: Approved glasses have Z87 printed or stamped on them
TOOL USE AND CARE
1. USE CLAMPS OR OTHER PRACTICAL MEASURES TO SECURE AND SUP-
PORT THE won K PIECE TO A STABLE PLATFORM. Holding the work piece by
hand or against your body is unstable and could lead to a loss of control.
2. DO NOT FORCE THE TOOL. Use the correct tool for your application The correct
tool will do the job better and safer at the rate for which it was designed. Do not
use the tool for purpose for which it was not intended.
3. DO NOT USE TOOL IF THE SWITCH DOES NOT TURN IT ON OR OFF. Any tool
that cannot be controlled with the switch is dangerous and must be repaired
4. DISCONNECTTHE PLUG FROM THE POWER SOURCE BEFORE MAKING
ANY ADJUSTMENTS, CHANGING ACCESSORIES OR STORING THE TOOL.
Such preventive safety measures reduce the risk of starting the tool accidentally
5. KEEP CUTTING TOOLS SHARP AND CLEAN. Properly maintained tools, with
sharp cutting edges, are less likely to bind and easier to control, When mounting
saw blades be certain that the arrow on the blade matches the direction of the ar-
row marked on the tool and that the teeth are also pointing in the same direction,
6. INSPECT THE GUARDS BEFORE USING A TOOL. KEEP GUARDS IN PLACE
and in working order, Never operate the tool with any guard or cover removed
Make sure all guards are operating properly before each use,
Owner's Hanua!
GENERAL SAFETY RULES
7. CHECK MOVING PARTS FOR BINDING OR ANY OTHER CONDmON THAT
MAY AFFECTTHE NORMAL OPERATION OR SAFETY FEATURES OFTHE
TOOL. if damaged, have the tool serviced bMore using the tool Many accidents
are caused by poorly maintained tools.
8. DO NOT ALTER OR MISUSE THE TOOL. Any alteration or modification is a
misuse and may result in serious personal injury,
9. THE USE OF ANY OTHER ACCESSORIES NOT SPEClRED IN THIS MANUAL
MAY CREATE A HAZARD. Accessories that may be suitable for one type of tool,
could create a risk of injury when used on an inappropriate tool
10. KEEPTHE TOOL AND ITS HANDLE DRY, CLEAN AND FREE FROM OIL
AND GREASE. Always use a clean cloth when cleaning Never use brake fluids.
gasoline, petroleum-based products, or any strong solvents to clean your tool
Following this rule will reduce the risk or loss of control and deterioration of the
plastic housing
11. INSPECT THE TOOL CORDS PERIODICALLY. If your cord is damaged, have
it repaired by a qualified service technician at an authorized service facility. Stay
constantly aware of the cord location and keep it well away from the rotating
blade,
12. MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION. When using
an exlension cord, be sure to use one heavy enough to carry the current your tool
will draw An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. A wire gauge size (AW G.) of at least 14 is recommend-
ed for an extension cord 25 feet or less in length. If in doubt, use the next heavier
gauge The smaller the gauge number, the heavier the cord
13.THE DUST GENERATED by certain woods and wood products can be injurious
to your health. Always operate machinery in well ventilated areas and provide for
proper dust removal. Use wood dust collection systems whenever possible
14. USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes
Never use blade washers or bolts that are defective or incorrect. The maximum
blade capacity of your saw is 10" (254 ram)
15. BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE.
16. AVOID CUTTING NAILS. Inspect for and remove all nails from lumber before
cutting
17. NEVER TOUCH THE BLADE or other moving parts during use
18. NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT
WITH THE WORKPIECE.
19. DOUBLE CHECK ALL SETUPS. Make sure the blade is tight and not making
contact with the saw or workpiece before connecting to a power supply
Owner's Hanua!
ADDITIONAL SAFETY RULES FOR MITER SAWS
WARNING! Read and understand all the instructions before attempting to as-
semble or operate the toot. Failure to follow the instructions listed below could
result in electric shock, fire and/or serious personal injury,
SAVE THESE INSTRUCTIONS.
1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according
2. OBTAIN ADVICE FROMYOUR SUPERVISOR, instructor, or another qualified
3. FOLLOW ALL WIRING CODES and recommended electrical connections
4. ALWAYS KEEPTHE BLADE GUARD IN PLACE and in working order
5. USE CLAMPSTO SUPPORT THE WORKPIECE WHENEVER POSSIBLE. IF
6. DO NOT REACH IN BACK OFTHE SAW BLADE BEHINDTHE FENCEWITH
7. NEVER CROSSYOUR HAND OVER THE INTENDED LINE OF CUTTING. Sup-
8. ALWAYS DISCONNECTTHE POWER CORD FROMTHE POWER SOURCE
9. MITER SAWS ARE INTENDED TO CUT WOOD OR WOODLIKE PRODUCTS,
10. INSPECTYOUR WORKPIECE BEFORE CUTTING. If the workpiece is bowed
11. DO NOT USE THE SAW UNTIL THE TABLE IS CLEAR OF ALL TOOLS, WOOD
12. DO NOT FEED THE WORKPIECE INTO THE BLADE OR CUT "FREEHAND"
Refer to them often and use them to instruct others,
to the instructions
person if you are not familiar with the operation of this machine,
SUPPORTING THE WORKPIECE BY HAND, YOU MUST ALWAYS KEEPYOUR
HAND OUTSIDE OF THE "NO HAND" AREA AS MARKED WITH A SYMBOL
ON THE BASE. DO NOT USE THIS SAW TO CUT PIECES THAT ARE TOO
SMALL TO BE SECURELY CLAMPED. Your hand, if placed inside the "No
Hands" region, can easily slip or be pulled into the blade,
EITHER HAND FOR ANY REASON. The proximity of the spinning saw blade to
your hand may not be obvious and you may be seriously injured
porting the workpiece "cross handed" i,e holding the left side of the workpiece
with your right hand is very dangerous,
BEFORE MAKING ANY ADJUSTMENTS OR ATTACHING ANY ACCESSO-
RIES. You may unintentionally start the saw, leading to serious personal injury
THEY CANNOT BE USED WITH ABRASIVE CUTOFF WHEELS FOR CUTTING
FERROUS MATERIAL SUCH AS BARS, RODS, STUDS, ETC. HOWEVER
, IF CUTTING MATERIALS LIKE ALUMINUM OR OTHER NON-FERROUS
METALS, USE ONLY SAW BLADES SPECIFICALLY RECOMMENDED FOR
NON-FERROUS METAL CUTTING. Cutting ferrous materials causes excessive
sparking and will damage the lower guard and will overload the motor,
or warped, clamp it with the outside bowed face toward the fence, Always make
certain that there is no gap between the workpiece, fence and table along the line
of the cut, Bent or warped workpieces carl twist or lock and may cause binding on
the spinning saw blade while cutting, Also, make sure there are no nails or foreign
objects in the workpiece
SCRAPS, ETC. Small debris or loose pieces of wood or other objects that contact
the revolving blade can be thrown with high speed at the operator,
IN ANYWAY.THE WORKPIECE MUST BE STATIONARY AND CLAMPED OR
BRACED BYYOUR HAND. The saw blade must be fed through the workpiece
smoothly and at a rate which will not overload the saw's motor
Owner's Manual
ADDITIONAL SAFETY RULES FOR MITER SAWS
13. CUT ONLY ONE WORKPIECE AT A TIME. Multiple workpieces cannot be ad-
equately clamped or braced and may bind on the blade or shift during cutting.
14. BE CERTAIN THE MITER SAW IS MOUNTED OR PLACED ON A LEVEL, FIRM
WORK SURFACE BEFORE USING. A level and firm work surface reduces the
risk of the miter saw becoming unstable,
15. PLAN YOUR WORK. Provide adequate support accessories such as tables, saw
horses, table extension, etc, for workpieces wider or longer than the table top,
Workpieces longer or wider than the miter saw table can tip if not securely sup-
ported, if the cutoff piece or workpiece tips it can lift the lower guard or be thrown
by the spinning blade,
16. DO NOT USE ANOTHER PERSON AS A SUBSTITUTE FOR ATABLE EXTEN-
SION OR AS ADDITIONAL SUPPORT. Unstable support for the workpiece can
cause the blade to bind or the workpiece to shift during the cutting operation
pulling you and the helper into the spinning blade
17.THE CUTOFF PIECE MUST NOT BE JAMMED AGAINST OR PRESSURED BY
ANY OTHER MEANS AGAINSTTHE SPINNING SAW BLADE. if confined, ie,
using length stops, it could get wedged against the blade and thrown violently
18. ALWAYS USE A CLAMP OR A FIXTURE DESIGNED TO PROPERLY SUP-
PORT ROUND MATERIAL SUCH AS DOWEL RODS, ORTUBING. Rods have a
tendency to roll while being cut, causing the blade to "bite" and pull the work with
your hand into the blade,
19.WHEN CUTTING IRREGULARLY SHAPED WORKPIECES, PLAN YOUR WORK
SO ITWILL NOT SLIP AND PINCH THE BLADE AND BE TORN FROM YOUR
HAND. A piece of molding, for example, must be lie flat or be held by a fixture or
jig that will not let it twist,, rock or slip while being cut,
20. LETTHE BLADE REACH FULL SPEED BEFORE CONTACTINGTHE WORK-
PIECE. This will help avoid thrown workpieces.
21. IF THE WORKPIECE OR BLADE BECOMES JAMMED OR BOGGED DOWN,
TURN THE MITER SAW "OFF" BY RELEASING SWITCH. Wait for all moving
parts to stop and unplug the miter saw, then work to free the jammed material
Continued sawing with a jammed workpiece could cause a loss of control or dam-
age to the miter saw.
22.THE BRAKING ACTION OFTHE SAW CAUSESTHE SAW HEAD TO JERK
DOWNWARD. Be ready for this reaction when making an incomplete cut or when
releasing the switch before the head is completely in the down position
23. AFTER FINISHING THE CUT, RELEASE THE SWITCH, HOLD THE SAW ARM
DOWN AND WAiT FOR BLADE TO STOP BEFORE REMOVING WORK OR
CUTOFF PIECE. Reaching with your hand under a coasting blade is dangerous
24. GUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly
and the workpiece is driven back towards the operator It can pull your hand into
the blade resulting in serious personal injury Stay out of the blade path and turn
the switch off immediately if the blade binds or stalls
25. AVOID KICKBACK (work thrown back toward you) by:
• Keeping the blade sharp and free of rust and pitch
• Never cut a workpiece that is twisted or warped, or does not have a straight
edge to guide along the fence
• Never saw a large workpiece that cannot be controlled
• Never saw a workpiece with loose knots or other flaws
8wner's Manual
ADI]IT|ONAL
Owner's Manua!
SAFETY RULES FOR MITER SAWS
26. NEVER altempt to free a stalled saw blade without first tulning the machine
"OFF".
27. NEVER PERFORM LAYOUT, assembly or set-up the workpiece on the table/work
area when the machine is running.
28. ALWAYS TURN THE MACHINE "OFF", disconnect the machine from the power
source, and clean the table/work area before leaving the machine. LOCKTHE
SWITCH IN THE "OFF" POSITION to prevent unauthorized use.
29. DO NOT ALLOW FAMILIARITY GAINED FROM FREQUENT USE OF YOUR
MITER SAW TO BECOME COMMONPLACE. Always remember that a careless
fraction of a second is sufficient to inflict severe injury.
30.THINK SAFETY! SAFETY IS A COMBINATION OF OPERATOR'S COMMON
SENSE, KNOWLEDGE OF THE SAFETY AND OPERATING INSTRUCTIONS
AND ALERTNESS AT ALL TIMES WHENTHE MITER SAW IS BEING USED.
WARNING! SOME DUST CREATED BY POWER SANDING, SAWING, GRIND-
ING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals
known to cause cancer, birth detects or other [ep[oductive harm Some examples o
these chemicals me:
* Leadh'omlead-basedpaints,
Cl7stalline silica h'otT} bricks and cement and other masonl 7 products, and
° At_enicandchromiumfromchemically-treatedlumbet:
Your risk h'om these exposures varies, depending on how often you do this type of work,
To reduce your exposure to these chemicals: work in a weft ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
31. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERAT-
ING THE TOOL. Learn the tool's application and limitations as well as the specific
hazards that accompany it.
32. SAFETY RULES FOR LASER LIGHTS
The laser guide used in the tool is Class I with a maximum output of <1row and a
wavelength of 650rim.The laser guide does not normally present an optical hazard,
although staring at the beam may cause flash blindness.
CAUTION.The use of optical in struments with this laser product will increase the
chance of eye damage.
Do not stare into the laser beam.
The laser shall be used and maintained in accordance with the manufacturer's instructions.
Never aim the beam at any person or an object other thanthe work piece.
Always ensure the laser beam is aimed at a sturdy work piece without a reflective surface,
i.e. wood or rough coated surfaces are acceptable.Bright shiny reflective sheet or the like
is not suitable for laser use as the reflective surface could direct the beam back at the
operator.
ELECTRICAL
O_rner's Manual
POWER CONNECTIONS
The saw has a precision-buift electric motor. It should be connected to a power
supply that is 120 volts, 60 Hz, AC only (normal household current). Do not
operate this tool on direct current (DC). A substantial voltage drop will cause a
loss of power and motor will overheat. Before connecting the motor to the power
line, make sure the switch is in the "OFF" position and be sure that the electric
current is of the same characteristics as indicated on the machine. All line con-
nections should make good contact. Running on low voltage will damage the
motor. If your tool does not operate when plugged into an outlet, double-check
the power supply.
WARNING! Do not expose the machine to rain or operate the machine in
damp locations.
SPEED AND WIRING
The no-load speed of this tool is approximately 4500 rpm. This speed is not con-
stant and decreases under a load or with lower voltage. For voltage, the wiring
in a shop is as important as the motor's horsepower rating. A line intended oniy
for lights cannot properly carry a power tool motor. Wire that is hea W enough for
a short distance will be too light for a greater distance. A line that can support
one power tool may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
WARNING! This machine must be grounded while in use to protect the opera-]
tor from electric shock.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This machine
is equipped with an electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching outlet that is prop-
erly installed and grounded in accordance with a_l _oca_ codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper
outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can resuft in risk of
electric shock.
Check with a qualified electrician or service personnel if the grounding instruc-
tions are not completeiy understood, or if in doubt as to whether the machine is
properly grounded.
J
%
J
O_ner'-_ Manual
ELECTRICAL
Repair or replace damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet like the one shown in
figure 1. It also has a grounding pin like the one shown.
2. Grounded, cord-connected machines intended for use on a supply circuit
having a nominal rating less than 150 volts:
If the machine is intended for use on a circuit that has an outlet that looks like
the one illustrated in Fig. 2, the machine will have a grounding plug. A tempo-
rary adapter, which looks like the adapter illustrated in Fig. 2, may be used to
connect this plug to a matching 2-conductor receptacle as shown in Fig. 2 if a
properly grounded outlet is not available. The temporary adapter should be used
only until a properly grounded outlet can be installed by a qualified electrician.
The green-colored metal ear", extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box. Whenever the
adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Cana-
dian Electric Code.
I_ ARNmNG! In all cases, make certain the receptacle in question is properly I
grounded. To prevent possible electrical hazards, have a qualified electrician
check the receptacle if you are not sure.
GROUNDEDOUTLETBOX
J
ELECTRICAL
8wner's Manual
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condi-
tion and is a 3-wire extension cord which has a 3-prong ground type plug and
matching receptacle which will accept the machine's plug. When using an exten-
sion cord. be sure to use one heavy enough to carry the current of the machine.
An undersized cord will cause a drop in line voltage, resulting in loss of power
and causing the motor to overheat. Use the chart provided below to determine
the minimum wire size required in an extension cord. Only round jacketed cords
listed by Underwriter's Laboratories (UL) shouid be used. If in doubt, use the
next heavier gauge. The smailer the gauge number, the heavier the cord.
**Ampere rating (on too} faceplate)
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16
50' 16 16 16 14
100' 16 16 14 12
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension cord that is designed for
outside use. This is indicated by the letters "WA" on the cord's jacket.
Before using an extension cord, inspect it for ioose or exposed wires and cut or
worn insulation.
WARNING! Keep the extension cord clear of the working area. Position the "_
cord so that it will not get caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so can result in serious per-
sonal injury.
WARNING! Check extension cords before each use. If damaged replace im-
mediately Never use tool with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious injury
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0
7.1q2.0 12.1-16.0
14 14
14 12
10
J
GROUNDING
PIN COVER OF GROUNDED
I-I_'g.1 OUTLETBOX
UNPACKING AN1) CLEANINS
This product requires assembly.
1. Remove the packing materials from around your tool. Do not discard the
packing material until you have carefully inspected and satisfactorily oper-
ated the tool.
2. Separate and remove all loose parts from the shipping container(s). Check
parts against the list of loose parts.
3. Carefully lift the tool from the carton by using the carrying handle and place it
on a firm, level work surface.
4. Remove the protective oil that is applied to all unpainted metal surfaces.This
coating may be removed with a soft cloth moistened with kerosene or WD-
40 ® (do not use acetone, gasoline or lacquer thinner for this purpose).
5. After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
6. Inspect the tool carefully to make sure no breakage or damage occurred
during shipping.
7. The saw is factory set for accurate cutting. After assembling it, check for
accuracy. If shipping has influenced the settings, refer to specific procedures
explained in this manual.
8. When boxed or during storage and transportation the saw head is locked
in the down position. To release the head apply downward pressure to the
handle and pull out the lock pin and allow the head to rise gently to its upper
position.
Fig. 2
8wner's Manual
b(ITER SAW PARTS
Before attempting to use this product, familiarize yourself with a_l operating
features and safety ru_es.
Upper Blade Guard Main Handle
Dust Extraction Port
Extension Bar
Owner's Manual
. Motor
Lower Blade Guard
;aw Blade
Base
I_lb WARNING! If anyparts are missing do not operate this tool until the missing I
I_ WARNING, Befo ..... ingth ..... Lockthemiterlockknobin45°position.)
parts are replaced. Failure to do so could result in serious personal injury.
ure to comply could result in accidental starting and serious personal injury.
_ WARNING[ Do not connect to power supply until assembly is complete. Fail-
Lock bevel lock lever. Pull the head assembly completely toward you and
tighten the slide rail lock knob. Lock head assembly in the down position.
Never carry the tool by the slide rails, this may cause blade damage.
Never carry the tool by the cord or head assembly power switch handle. Dam-
age to insulation could cause an electric shock. Damage to wire connections
could cause a fire.
J
Bench Mounting Holes
Carbon Brush C_ ust Bag
Table Lock Pin
Rotating Table
Loading...