Steelcraft Automotive 82200 User Manual
DOUBLE TUBE REAR BUMPER GUARD
1
Rear Bumper Guard
4
12-1.75mm x 35mm Hex Bolts
1
Driver/Left Frame Mounting Bracket
12
12mm x 24mm OD x 2.5mm Flat Washers
1
Passenger/Right Frame Mounting Bracket
8
12mm Nylon Lock Nuts
1
12mm Long Rod Bolt (passenger side)
2
12mm Plastic Retainers
1
12mm Short Rod Bolt (driver side)
Passenger/Right
Side Frame Bracket
Driver/Left Side
Frame Bracket
Short 12mm Rod Bolt
(Driver/Left Side)
Long 12mm Rod Bolt
(Passenger/Right Side)
Rear
07-12 JEEP WRANGLER J/K
PARTS LIST:
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
WARNING: ALLOW TIME FOR THE MUFFLER TO COMPLETELY COOL BEFORE
INSTALLING REAR BUMPER GUARD BRACKETS.
2. Start installation on the passenger side of the vehicle. Select the passenger side Mounting
Bracket. Temporarily hold the Bracket up in place on the crossmember to determine correct
hole locations for mounting hardware, (Figure 1).
3. Remove the factory hex bolt on back of crossmember, (Figure 1). Insert Long 12mm Rod Bolt
into the hole in the bottom of the crossmember and out the outer hole, (Figures 2A & 2B).
Hold the Bracket up in place over the threaded end of the Rod Bolt. Insert the factory hex bolt
through the tab on the Mounting Bracket and back into the crossmember. Secure the Bracket
to the Rod Bolt with (1) 12mm Flat Washer and (1) 12mm Nylon Lock Nut, (Figure 4). Do not
tighten hardware at this time. NOTE: 12mm Plastic Retainers have been provided to help hold
the Rod Bolt in place during Bracket installation. Thread the Retainer onto the Rod Bolt and
tight against the frame to hold Rod Bolt in place if needed.
4. Repeat Steps 2 - 3 for driver side Mounting Bracket installation, (Figures 3A & 3B).
5. Carefully unwrap the Bumper Guard. Bolt the Bumper Guard to the inside of the Brackets with
(4) 12mm Hex Bolts, (8) 12mm Flat Washers and (4) 12mm Nylon Lock Nuts, (Figure 4).
6. Level and adjust the Bumper Guard and Brackets and tighten all fasteners.
7. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Bumper Guard.
For gloss black finishes: Mild soap may be used to clean Bumper Guard.
Page 1 of 2 7/6/12 (DP)
DOUBLE TUBE REAR BUMPER GUARD
Remove factory
hex bolt
12mm Flat Washer
12mm Nylon Lock Nut
12mm Hex Bolts
12mm Flat Washers
12mm Nylon Lock Nuts
(Fig 1) Passenger side mounting location pictured
from below crossmember behind bumper
Insert Long Rod Bolt through this opening
in passenger side of crossmember
(Fig 2B) Use Long Rod Bolt for
passenger side installation
(Fig 2A) Use Long Rod Bolt for
passenger side installation
(Fig 3A) Use Short Rod Bolt
for driver side installation
(Fig 3B) Use Short Rod Bolt
for driver side installation
(Fig 4) Passenger side Bracket installation pictured
Factory
hex bolt
Front
Rear
Rear
Rear
07-12 JEEP WRANGLER J/K
Page 2 of 2 7/6/12 (DP)
Loading...