Steelcraft Automotive 170300 User Manual

ALUMINUM VIEWPOINT RUNNING BOARDS

(4) 12mm x 35mm
Hex Bolt Plates

(6) 12mm x 35mm Low
Profile Bolt Plate

1

Driver Side Running Board

4

12-1.75mm x 35mm Large Bolt Plates

1

Passenger Side Running Board

10

12mm Plastic Retainers

2

Front Bracket Arms

10

12mm x 32mm OD x 3mm Flat Washers

2

Front Inner Mounting Brackets

10

12mm Lock Washers

1

Passenger Side Front Outer Mounting Bracket

10

12mm Hex Nuts

1

Driver Side Front Outer Mounting Bracket

16

8mm x 25mm Hex Bolts

2

Center Bracket Arms

32

8mm x 22mm x 2mm Flat Washers

2

Center Mounting Bracket

16

8mm Lock Washers

1

Driver Side Rear Bracket Arm

16

8mm Hex Nuts

1

Passenger Side Rear Bracket Arm

12

6mm T-Bolts

1

Driver Side Rear Mounting Bracket

12

6mm x 22mm x 2mm Flat Washers

1

Passenger Side Rear Mounting Bracket

12

6mm Lock Washers

6

12-1.75mm x 35mm Low Profile Bolt Plates

12

6mm Hex Nuts

Passenger/Right Rear

Mounting Bracket

Passenger/Right Rear
Mounting Bracket Arm

(2) Center Mounting Brackets

(2) Center Bracket Arms

Passenger/Right Front Outer
Mounting Bracket

(2) Front Bracket Arms

(2) Front Inner
Mounting Brackets

Driver/Left Front Outer
Mounting Bracket

Driver/Left Rear
Mounting Bracket Arm

Driver/Left Rear
Mounting Bracket

Passenger/Right Running Board

Driver/Left Running Board

Front

2011-12 HYUNDAI SANTA FE

PARTS LIST:

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting at the front, passenger side of the vehicle, remove the plug in the back of the body panel above
the pinch weld and the rubber plug in the bottom of the inner frame channel, (Figures 1B & 2B).

IMPORTANT: Plugs may be covered with sealant or undercoating. Brackets must fit flush against sheet

metal. Scrape of any excess sealant or undercoating. Repeat this Step for all mounting locations.

Page 1 of 5 10/19/12(DP)

ALUMINUM VIEWPOINT RUNNING BOARDS

2011-12 HYUNDAI SANTA FE

3. Select (1) 12mm Low Profile Bolt Plate and (1) 12mm Plastic Retainer, (Figure 1A). Partially thread the

Retainer onto the Bolt Plate. Insert the Bolt Plate into the hole in the back side of the body panel.
Thread the Retainer down until it is tight against the sheet metal, (Figure 1B). IMPORTANT: The
Plastic Retainer is designed to hold the Bolt Plate in place and prevent it from falling into the frame
channel during Bracket installation. Attach the offset passenger side front Mounting Bracket to the Bolt
Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut, (Figures 2B & 3).
Snug but do not tighten hardware.

4. Select (1) 12mm Hex Head Bolt Plate and (1) 12mm Plastic Retainer, (Figure 2A). Insert the Bolt Plate
into the hole in the bottom of the frame channel as previously described, (Figure 2B). Next, attach (1)
Inner Front Mounting Bracket to the Bolt Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and
(1) 12mm Hex Nut, (Figure 3). Do not tighten hardware at this time.

5. Hold (1) long front Bracket Arm up in position between the (2) previously installed Brackets, (Figure 4).
Make sure the slots in the Arm line up with the inner and outer Mounting Brackets. Hold the inner
Bracket straight and tighten the Hex Nut on the inner Bracket only. Bolt the Bracket Arm to the inner
and outer Brackets with (4) 8mm x 25mm Hex bolts, (8) 8mm Flat Washers, (4) 8mm Lock Washers
and (4) 8mm Hex Nuts, (Figure 4). Snug but do not fully tighten hardware at this time.

6. Move to the center mounting location mid way down the side of the vehicle. Remove the rubber plug
on the back of the inner body panel as described in Step 2. Install (1) 12mm Low Profile Bolt Plate and
(1) 12mm Plastic Retainer, (Figure 5A). Insert the Bolt Plate into the hole in the back side of the body
panel as previously described. Attach (1) Center Mounting Bracket to the Bolt Plate with (1) 12mm Flat
Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut, (Figure 5B). Snug but do not tighten
hardware at this time.

7. Attach (1) Center Bracket Arm to the Center Bracket with (2) 8mm x 25mm Hex Bolts, (4) 8mm Flat
Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts, (Figure 6). Snug but do not fully tighten
hardware at this time.

8. Move toward the rear of the vehicle. Locate and remove the rubber plugs in the bottom of the frame
channel and the back of the inner body panel similar to as described in Step 2, (Figure 7).

9. Select (1) 12mm Low Profile Bolt Plate and (1) 12mm Plastic Retainer, (Figure 8A). Insert the Bolt
Plate into the narrow oval hole in the bottom of the frame channel, (Figure 8B). Next, insert (1) 12mm
Hex Head Bolt Plate and (1) 12mm Plastic Retainer into the hole in the back of the inner body panel as
previously described, (Figures 9A & 9B). Attach the passenger side rear mounting Bracket to the Bolt
Plates with (2) 12mm Flat Washers, (2) 12mm Lock Washers and (2) 12mm Hex Nuts, (Figure 10).
Snug but do not tighten hardware at this time.

10. Select the passenger side rear Bracket Arm. Bolt the Bracket Arm to the front facing side of the rear
Bracket with (2) 8mm x 25mm Hex bolts, (4) 8mm Flat Washers, (2) 8mm Lock Washers and (2) 8mm
Hex Nuts, (Figure 10). Snug but do not fully tighten hardware at this time.

11. Carefully unwrap the passenger side Running Board. From the front, slide (3) T-Bolts into each
channel in the bottom of the Running Board, (Figure 11). Slide the T-Bolts forward or back to line up
with the slots in the (3) Mounting Brackets. Hold the Running Board up to the vehicle at a slight angle
and gently push it into position against the rocker panel. Insert the T-Bolts through the slots in the
Brackets. NOTE: It may be necessary to loosen the Bracket hardware to insert the Running Board
between the Brackets and the body. Attach the Running Board to the Mounting Brackets with the
included (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 12). Do not
tighten hardware at this time.

12. Level and adjust the Running Board properly and tighten all hardware.

13. Repeat Steps 2 - 12 for driver side Running Board installation.

14. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be

used also to clean the Running Board.
For gloss black finishes: Mild soap may be used to clean the Running Board.

Page 2 of 5 10/19/12(DP)