Steelcraft Automotive 133800 User Manual

VIEWPOINT ALUMINUM RUNNING BOARD

1

Driver/Left Running Board

12

8mm x 22mm OD x 2mm Flat Washers

1

Passenger/Right Running Board

12

6mm x 20mm “T” bolts

2

Front Mounting Brackets

12

6mm Lock Washers

4

Center & Rear Mounting Brackets

12

6mm x 22mm OD x 2mm Flat Washers

12

8-1.25mm x 30mm Hex Bolts

12

6mm Hex Nuts

12

8mm Lock Washers

(4) Center & Rear
Mounting Brackets

Passenger/Right Side Running Board
Driver/Left Side Running Board

(2) Front
Mounting
Brackets

Front

Rear

Longer angle to front

2010-12 TOYOTA 4RUNNER

SR5 AND LIMITED MODELS (EXCL TRAIL EDITION)

PARTS LIST:

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting on the passenger side of the vehicle, remove the existing (2) factory bolts located by the front

tire opening securing the factory rocker panel bracket to the vehicle, (Figure 1). Select (1) Front
Mounting Bracket. Hold the Front Bracket over the rocker panel bracket and line up the (2) mounting
holes. Secure the brackets to the vehicle using the included longer (2) 8mm x 30mm Hex Bolts, (2)
8mm Lock Washers and (2) 8mm Flat Washers, (Figure 2). Do not tighten hardware at this time.

3. The center and rear brackets are identical. Select (1) Center/Rear Bracket and repeat the procedure as
described in Step 2 to install it in the center mounting location, (Figure 3). NOTE: Install (1) mounting
bracket at a time. Do not tighten hardware at this time.

4. Repeat Step 3 for rear Mounting Bracket installation.

5. Carefully unwrap the Running Board and select passenger side Board. Select (6) 6mm T-Bolts. Insert

(3) T-Bolts into each channel on the bottom of the Running Board, (Figure 4). Slide the T-Bolts forward
or back to line up with the (3) previously installed Mounting Brackets, (Figure 5). Hold the Running
Board up to the vehicle at a slight angle and gently push it into position against the rocker panel,
(Figure 6). Line up the T-Bolts with the slots in the Brackets.

6. Attach the Running Board to the Mounting Brackets with the included (6) 6mm Flat Washers, (6) 6mm
Lock Washers and (6) 6mm Hex Nuts, (Figures 7 & 8). Do not tighten at this time.

7. Level and adjust the Sidebar as desired and tighten all hardware. Repeat Steps 2 – 6 for the driver side
Running Board installation.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Page 1 of 3 9/17/12 Rev1(DP)

VIEWPOINT ALUMINUM RUNNING BOARD

(Fig 1) Passenger side front mount pictured

Fig 2

(Fig 3) Passenger side rear bracket location pictured

Install the Mounting Brackets
one at a time over the factory
rocker panel brackets

Remove factory hex bolts
Front

Rear

(Fig 4) Insert T-Bolts into channels
on bottom of Running Board

(2) 8mm x 30mm Hex Bolts
(2) 8mm Flat Washers
(2) 8mm Lock Washers

Front

2010-12 TOYOTA 4RUNNER

SR5 AND LIMITED MODELS (EXCL TRAIL EDITION)

To protect your investment, wax this product after installing. Regular waxing is recommended to add a

protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild
soap may be used also to clean the Running Board.

For gloss black finishes: Mild soap may be used to clean the Running Board Brackets.

Passenger Side Installation Pictured

Page 2 of 3 9/17/12 Rev1(DP)