Steelcraft SAVVI Instruction Book

www.britax.com.au

Series TK321

CONVERTIBLE SEAT STROLLER

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

C

O

V

E

R

T

S

T

O

B

A

S

S

I

N

E

T

Travel system compatible:

Suitable for use with Britax

Safe n Sound Unity baby capsule

(sold separately)

ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE
OF THIS STROLLER.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS
ESSENTIAL.

• USE GREAT CARE WHEN USING THE STROLLER ON STAIRS,
ESCALATORS, TRAVELATORS OR OTHER MOVING SURFACES.

• IT IS RECOMMENDED TO REMOVE THE CHILD FROM THE STROLLER
BEFORE GOING UP OR DOWN STAIRS OR ESCALATORS.

• DO NOT ALLOW CHILDREN TO STAND ON THE SEAT.

• DO NOT HANG BAGS OR GOODS FROM THE HANDLE AS THIS
COULD CAUSE THE STROLLER TO TIP OVER.

• DO NOT LEAVE THE STROLLER AND ITS ACCESSORIES NEAR AN
OPEN FIRE OR EXPOSED FLAME.

• DO NOT PLACE MORE THAN 12 KG IN THE BASKET, OR 1KG IN THE
CANOPY POCKET (IF SUPPLIED).

IMPORTANT NOTES:

IMPORTANT NOTES

02

WARNINGS: TO AVOID INJURY OR DEATH:

ALWAYS APPLY THE BRAKES WHENEVER THE PRAM/STROLLER
IS STATIONARY.

• DO NOT LEAVE CHILDREN UNATTENDED.

• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.

• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.

• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU
ADJUST THE PRAM/STROLLER.

• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED
FOR USE WITH THIS STROLLER BY BRITAX.

• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH
THIS STROLLER.

• THE MAXIMUM WEIGHT OF THE CHILD USING THIS STROLLER IN
THE BASSINET MODE IS NOT TO EXCEED 9KG. THE MAXIMUM
WEIGHT OF THE CHILD USING THIS STROLLER IN THE SEAT MODE IS
NOT TO EXCEED 20KG.

This CAUTION Symbol is shown at certain steps in
this Instruction Manual to highlight the danger
of being injured by moving parts.

CAUTION

WARNINGS

03

The SMART lifting technique

This technique can be used to pick up small light loads from low levels.

Size up the Load

• Assess the load (size, shape and weight).

• Assess whether the load needs to be moved;

• Where is it going to be placed” Check that there are no obstructions;

• Assess whether mechanical or human assistance is required.

Move the Load as close to the body as possible

• A load is heavier to lift or carry if it is not close to the body.

• The whole hand should be used to ensure a rm grip.

Always bend your knees

• Maintain balance.

• Keep feet apart and in a comfortable position.

• Minimise lower back bending.

• Bend knees preferable at as large an angle as possible but not at a right
angle - use a semi squat in preference to a full squat.

Raise the load with your legs

• Achieve the lift smoothly and without jerkiness.

• Maintain the normal curvature of the spine to allow the force of the
load to be distributed evenly from the spine to the pelvis.

Turn your feet in the direction that you want to move the load.

• Avoid unnecessary bending, twisting and reaching.

• Change direction by turning your feet and not your back.

• To set the load down, squat down, keep your head up and let your legs
do the work.

Remember to ‘THINK TALL’ chest lifted, shoulders relaxed, chin
tucked in and head level.

MANUAL HANDLING TECHNIQUES

04

A 1 x Frame B 1 x Convertible

bassinet/seat unit

C 1 x Canopy

D 1 x Arm Bar E 2 x Front Wheels F 2 x Rear wheels

PARTS LIST

05

G 1 x Bassinet liner

J 2 x Shoulder pads K 2 x CLICK N GO Receivers

H 1 x Boot cover I 1 x Rain cover

R

L

IMPORTANT NOTES:

PLEASE REFER TO PAGE 4 FOR SMART LIFTING TECHNIQUES.

• RELEASE THE STORAGE LATCH WITH DUE CARE AND OPEN THE FRAME.

• WHEN OPENING THE STROLLER, BE AWARE OF THE DANGER OF BEING
INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE
PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.

• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE
INJURED WHEN THE STROLLER IS BEING UNFOLDED, DUE CARE
SHOULD BE EXERCISED.

• KEEP CHILDREN CLEAR OF THE STROLLER WHEN UNFOLDING THE
STROLLER.

• OPEN THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE
YOUR HANDS.

STROLLER ASSEMBLY

OPENING THE STROLLER FRAME

OPENING THE STROLLER FRAME

06

A Lay the frame on a at surface

and slide the latches on both
handle tubes towards the
handle and then lift the handle
upwards.

B Continue to lift the handle
upwards until the frame is
fully open and locked.

CAUTION

A To attach the front wheels,
insert each front swivel wheel
assembly into the wheel
moulding and push in until you
hear a ‘click’ which indicates the
wheel is locked in. Pull on each
wheel to make sure it is
securely attached. Repeat the
process if not locked in.

ATTACHING THE FRONT & REAR WHEELS

STROLLER ASSEMBLY

07

B To attach the rear wheels, insert

each wheel axle into the
moulding and push in until you
hear a ‘click’ which indicates the
wheel is locked in. Pull on each
wheel to make sure it is securely
attached. Repeat the process if
not locked in.

STROLLER ASSEMBLY

IMPORTANT NOTE:

ATTACHING THE SEAT TO THE STROLLER FRAME

08

A Hold the stroller seat over the

frame. Align the stroller seat
connectors over the connection
sockets on the frame. Push down
on the seat until both stroller
seat connectors have locked into
the frame sockets.

ALWAYS REMOVE YOUR CHILD FROM THE STROLLER SEAT BEFORE
INSTALLING THE STROLLER SEAT TO THE FRAME.

PLEASE NOTE: The seat is reversible so it can be attached to the frame in

the forward facing position or the rearward facing position.

CAUTION

B Pull up on both sides of the

seat to ensure that it is locked
into place correctly.

09

WARNING: WHEN A CHILD IS IN THE STROLLER IT IS

RECOMMENDED THAT THE ARM BAR IS ATTACHED TO THE
STROLLER AT ALL TIMES.

STROLLER ASSEMBLY

ATTACHING THE ARM BAR

A Insert the arm bar mouldings into the

sockets on each side of the stroller
frame and push down on the arm bar
until a ‘click’ is heard which indicates
the arm bar has locked into the
sockets. To assist with putting a child
in the stroller, you can release the arm
bar on one side. Press the button on
the side of the arm bar moulding and
pull the arm bar up and out of the
socket.
Rotate the arm bar clear of the stroller.
Reattach the arm bar after fastening
the child in the harness.

B To remove the arm bar, press the
button on each side of the arm bar
moulding and pull arm bar up and
out of the sockets.

10

STROLLER ASSEMBLY

The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE
SUN. The canopy or hood on this product will not give your child total

protection from the harmful rays of the sun.

IMPORTANT NOTE:

A Place the canopy on the stroller frame

and push the clips on the sides of the
canopy onto the stroller frame until they
snap into place.

ATTACHING THE CANOPY

B Attach the canopy to the seat unit with

the zipper. There is peek a boo window
with magnetic closer and zipped open
mesh panel for better ventilation.