Page 1
KEEP INSTRUCTIONS FOR FUTURE REFERENCE
PROFILE
Layback Stroller
series AX198
4000657
Page 2
11
To prolong the life of your nursery product keep it clean and do not leave it in the direct
sunlight for extended periods of time.
Removable fabric covers and trims may be cleaned using warm water with a household
soap or a mild detergent. Allow it to dry fully, preferably away from the direct sunlight.
HELPFUL HINTS
If the wheels squeak - use a silicon based spray or light oil ensuring it penetrates the
wheel and axle assembly.
When using your stroller at the beach - completely clean your stroller afterwards to
remove the sand and salt from the mechanisms and wheel assembly.
If there are compression marks on the tyres - use a domestic hair dryer to gently warm
the tyre and the compression marks should slowly disappear. (DO NOT OVERHEAT).
DO NOT DRY CLEAN, OR USE BLEACH.
Do not machine wash, tumble or spin dry, unless the care labeling on the product
permits these methods.
Non removable fabric covers and trims may be cleaned using a damp sponge with
soap or mild detergent. Allow it to dry completely before folding or storing it away.
In some climates the covers and trims may be affected by mould and mildew. To help
prevent this occurring, do not fold or store the product if it is damp or wet. Always
store the product in a well ventilated area.
Always check parts regularly for tightness of screws, nuts and other fasteners - tighten
if required. To maintain the safety of your nursery product, seek prompt repairs for bent,
torn, worn or broken parts. Use only those parts and accessories approved by Britax.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
CARE AND MAINTENANCE
www.britax.com.au
Page 3
03
A Hold the stroller by the handles and release the
storage latch.
B Hold the handles and allow the front legs to drop
towards the floor. Do not try to open the stroller by
forcing the handles apart.
C Push down on the lower locking bar until the
frame is fully opened and locked.
D Check that both the upper hinge and lower
locking bar are fully engaged.
2. TO ASSEMBLE THE FRONT SWIVEL WHEELS
A Take each front swivel wheel assembly and press it
onto each of the front legs.
B Check that each wheel is fully engaged and
secured by pulling against it.
1. TO OPEN THE STROLLER
A
B
A
C
A
Page 4
09
NOTE: Do not use the carrier with any other stroller.
Only use a Steelcraft stroller with the Unity
attachment bumper bar.
A Position the carrier over the stroller with the baby's
head end of the bassinet over the stroller bumper
bar.
B Lower the carrier and ensure that the latch slot
locates onto the bumper bar.
C Lower the foot end of the carrier until the latch
locks onto the bumper bar and rest foot end on the
seating area of the stroller.
D Raise and lock the stroller backrest to the middle
recline position. This is the recommended carrier
position for the baby.
E Fold the carrier handle down, and then check the
carrier is securely attached to the stroller bumper
bar by lifting the carrier before use.
NOTE: Do not lift the stroller by the carrier. It may
disengage.
2. INSATLLING THE UNITY™ CARRIER INTO THE STROLLER
Bumper Bar
Page 5
05
6. TO FIT THE BOOT COVER
A Place the boot cover over the leg rest.
Attach both the boot cover clips to the frame.
B Attach both the right hand and left hand boot cover
side attachments to the sides of the frame.
7. TO ADJUST THE LEG SUPPORT
A Lower the leg support by pressing up the release
latches located underneath on both sides of the leg
support. Then push the leg support down.
B Raise the leg support by lifting it until the release
latches lock into place.
8. TO ADJUST THE BACKREST
A Squeeze both the right hand and left hand latches
fully and pull them back towards the rear of the
stroller to the desired layback position.
B Lift the backrest to select a more upright seating
position.
DO NOT ADJUST THE BACKREST WHILE YOUR
CHILD IS IN THE STROLLER.
A
www.britax.com.au
Page 6
07
B1
B2
C
C
D
Storage
Latch
www.britax.com.au
11. TO FOLD THE STROLLER
A Remove the boot cover (if fitted), close the
canopy and place the backrest in the fully upright
position. Apply the brakes and lock the swivel
wheels.
B Lift the upper hinge lock (at the handles) and
the lower hinge lock (at the bottom).
C Depress and release the secondary lock and
push handles forward until the frame is fully
folded.
D Apply the storage latch. A carry handle is
supplied for ease of transport when stroller
is fully folded.
Loading...