Steamist TC-110 Installation And Operating Instructions Manual

Steambath Control

Model: TC-110

®

C

Installation and Operating Instructions

LISTED 995C

WARNING: Elderly persons, pregnant women, or those suffering from heart disease, high blood
pressure, diabetes, or who are otherwise not in good health, do not use this device unless

!

directed to do so by a physician. Also, do not use steambath while under the influence of alcohol.

IMPORTANT: The TC-110 Control will only function with one of the following Steamist Generator models:
SM-46, SM-79, SM-4, SM-5, SM-7, SM-8, SM-11, SM-12, and SM-15. (It will not work with Models:
System-18, System-24, & System-30 unless used in cunjuction with a Steamist thermostatic controller, such
as Model# TC-135 or DSC-425).

Control Features

NOTE: This control may be installed inside or outside the

steam room for operation of the system.

Start/Stop Key Pad: Press key pad and generator will

1.
begin producing steam in minutes. The generator will
remain on for 30 minutes when used with the model
SM-46, SM-79 SM-4, SM-5, SM-7, or SM-8 steam
generators and 60 minutes for larger generators.

1

START

STOP

2

Pressing the key pad a second time will stop the
Steam Generator.

Start/Stop Light: Indicates the Steam Generator is

2.
activated.

US

TC-110

Timer and Start/Stop Switch

Installation Instructions

1. Pre-Installation - Control Location

a)

The TC-110 control may be installed inside or
outside the steam room. For convenience the
recommended height from the floor is four feet.
Provide a 1” hole in the wall at this location (see
Figure 1).

IMPORTANT: Multi-conductor cable must be
installed so that the end will not be buried inside the
wall. The unit will not operate unless the control is
installed.

2. Electrical Rough-in

a)

Remove the multi-conductor cable from the control
packing box. Carefully route the multi-conductor
control cable from the Steambath Generator to the
TC-110 located either inside or outside the
steamroom (see Figure 2). Route multi-conductor
cable though a ¾” conduit to protect the cable from
damage and to facilitate replacement if necessary.

Cleaning Instructions: Use a damp cloth and mild soap.
Do NOT use abrasive cleaners which might scratch the
surface or the base of the control.

IMPORTANT: Run the
Control Cable through a
¾” conduit.

1“ Hole

located four feet

from the floor

Double-sided

Adhesive Pad

Figure 1

TC-110 Timer and

Start/Stop Switch

07/07

- 1 -

Pub. No. 526-D

3. Control and Cable Installation

a)

Locate the previously installed cable and black
plastic strain relief clamp which is in the control
packing box. Locate the knock-out on the steam
generator for the control cable (see Figure 2).

b)

Place strain relief around cable about seven inches
from the end and insert into the hole. Remove the
protective covering labeled, “Remove before
installation,” from the modular jack found on the PC

c)

board.
If a second control will be installed, plug the splitter
into the modular jack, this will allow two cables to be
plugged into the PC board.

.
A

.

0

S

.

.

2

Z

5

U

O

1

.

3

N

L

R

.

I

F

o

A

E

N

2

E

/

D

1

L

m

t

A

e

C

t

e

I

M

N

S

I

L

I

C

O

N

E

IMPORTANT: The Steamist supplied splitter must
be used. Locally purchased telephone splitters will
NOT work and void the warranty.

d)

Remove the protective cap from the
multi-conductor cable plug. Connect the cable to
the modular jack located on the printed circuit board

e)

of the Steam Generator.

f)

Close and secure generator cover.
Plug cable into receptacle on the back of the
TC-110 control. The receptacle is keyed for proper
installation.

WARNING: Test the control for operation before
continuing on to the next step.

¾“ Conduit

Multi-conductor

Control Cable

To Control

(25 feet)

Figure 3

g)

Peel adhesive liner from back of the control. Apply
the control to the wall. Press firmly and hold for a
few seconds.

h)

After the control is in place, apply silicone
(supplied) around the control to form a water tight
seal (see Figure 3).

IMPORTANT: If the TC-110 is mounted on the
inside of the shower, the adhesive backing on the
control will NOT seal it to the wall. It is the
responsibility of the installer to seal this control to
the wall using the silicone sealant provided.
Warranty is voided if the control is not completely
sealed to the wall.

Optional Splitter

for two controls

Modular Jack

Figure 2

Cable Installation

on Steam Generator

07/07

Printed

Circuit Board

Knock-outs for

Strain Relief

Clamps

Protective Covering

“Remove Before

Installation”

Pub. No. 526-D- 2 -