WPS-350-BUL-A-GR
WPS-350-BUL-A-WH
BULLET
CAMERA
INSTALLATION MANUAL
Review manual thoroughly before installation.
Retain for future reference.
WPS-350-BUL-A Installation Manual
CONTENTS
Safety Instructions ......................................................................................3
Features.......................................................................................................4
Package Contents ....................................................................................4
Installation Instructions ............................................................................... 7
Troubleshooting ..........................................................................................10
Dimensions .................................................................................................. 12
2
WPS-350-BUL-A Installation Manual
SAFETY INSTRUCTIONS
This information is provided to ensure your safety and to prevent physical
or nancial loss. Please read this document carefully before installing and
operating the camera.
1. Handle with care.
This camera is not designed to resist heavy impact. Use caution when
handling to avoid damage to sensitive internal components.
2. Do not install the camera under extreme temperatures.
This camera only operates under temperature conditions between
14˚F ~ 140˚F.
3. Do not mount the camera directly facing bright light sources.
Exposing the camera to strong light over long periods of time will damage
the camera’s sensor.
4. Do not supply voltage other than 12VDC.
Higher voltages will damage the camera’s electronic components.
5. Do not install the camera in environments with extreme humidity.
Installing camera in environments with extreme humidity may cause moisture
to condense on the surface of the lens or dome cover, which can affect
picture quality.
© 2013 Wirepath Surveillance
3
WPS-350-BUL-A Installation Manual
FEATURES
• 1/3” Sony Super-HAD II CCD
The Sony Super HAD II CCD is ideal for low lux illumination, resulting in a clear
and crisp image.
• Varifocal Auto-Iris Lens
This camera features a varifocal lens with a focal length of 4-9mm. The autoiris function intuitively manages the amount of light passing through the lens
for consistent image brightness..
• Weatherproof Housing
The IP66-rated weatherproof housing makes this camera ideal for
outdoor surveillance.
• Video Test Port
Adjust angle, zoom, and focus at the camera for fast and easy installation.
• External Zoom and Focus Adjustments
Adjust the camera without the need to remove the lens cap for quick
adjustments.
PACKAGE CONTENTS
(1) WPS-350-BUL-A
(1) DC Plug
(1) BNC Test Adapter
(3) Screws
(3) Wall Fasteners
(1) 3mm Allen key
(1) Foam gasket
(1) Installation Manual
(1) Spare Silica Pack in Vacuum sealed bag
NOTE: A POWER SUPPLY IS NOT INCLUDED WITH THIS CAMERA.
The PS-12DC-1A or WPS-PS multiple output power supplies are recommended.
4
WPS-350-BUL-A Installation Manual
OPTIONAL ACCESSORIES
Wirepath Surveillance offers a wide range of accessories that provide power
to the cameras, allow for various mounting options, and make connection to
the head end quick and easy.
MOUNTS
• WPS-MNT-FLUSH-BUL
Use when the camera needs to be attached to a ush mount junction box.
POWER SUPPLIES
Local Power Supplies
• PS-12DC-1A
12 Volt 1 Amp Power Supply for Cameras & IR Systems.
Remote Power Supplies
Use these remote power supplies to power all the cameras in the system from
a remote location.
• WPS-PS9-12VDC-10A
9 Output Power Supply - 12V DC, 10A - PTC Fuses
• WPS-PS18-12VDC-18A
18 Output Power Supply - 12V DC, 18A - PTC Fuses
© 2013 Wirepath Surveillance
5
WPS-350-BUL-A Installation Manual
WIRING ACCESSORIES
In addition to mounts and power supplies, Wirepath offers a full line of
accessories to easily send power, audio, and video over 2 conductors of
Cat5 wiring back to the head end.
Visit www.snapav.com for a complete listing of accessories.
• WPS-BAL-V-PIGTAIL
Mini Passive Video Balun with Pigtail
and Screw Terminals
• WPS-BAL-V-MINI
Mini Passive Video Balun with Pigtail
and Screw Terminals
• WPS-BAL-V-COMBO
Mini Passive Video Balun with Screw
Terminals Combo Pack
Contains: 1 WPS-BAL-V-PIGTAIL and 1
WPS-BAL-V-MINI
• WPS-BAL-VP
Passive Video and Power Balun
with RJ45
• WPS-BAL-VPA
Passive Video, Power, Audio Balun
with RJ45
• WPS-ACC-PWR-F & WPS-ACC-PWR-M
DC Power Plug with Screw Terminals
available in Male and Female
version 10packs.
• WPS-ACC-PWR-1X2
DC Power Splitter Cable - 1 Female
to 2 Male Connectors
• WPS-ACC-PWR-1X4
DC Power Splitter Cable - 1 Female
to 4 Male Connectors
• WPS-ACC-MIC
Mini Microphone 12V DC Amplied
• WPS-ACC-GND-ISO
Ground Loop Isolator Male to
Female BNCs
6
WPS-350-BUL-A Installation Manual
A
B
C
INSTALLATION INSTRUCTIONS
1. Prepare Camera for Mounting
Prior to mounting to the Camera, we recommend that the position and
angles be preset in order to speed installation. These settings can be ne-
tuned once the Camera is mounted.
A. Adjust Camera Rotation
B. Adjust Swivel of Camera
C. Adjust Camera Angle
2. Connect the Camera to the System
Recommended Cabling:
- Video RG59 or RG6
- Power Cat5e/6 or 18/2
A. Connect the BNC video output to the video in of a DVR or monitor.
B. Connect the DC Power In to a 12V DC 1A power supply using the included
WPS-ACC-PWR DC power adapter on the wire. The power supply can be
located at the head end of system if you prewire a power wire.
Important Note! Be sure that the polarity and the voltage of the power supply
connection is correct before attempting to power the camera. Backward
polarity or any more than a 12 volt DC power supply will damage the camera.
The power supply used must be rated to 1 amp per output minimum.
DC Plug
© 2013 Wirepath Surveillance
7
WPS-350-BUL-A Installation Manual
3. Mount the Camera
A. Mounting directly to a wall or eve:
A.1 - Use the Camera base as a template to mark the screw locations.
A.2 - Predrill holes in the marked locations.
A.3 - Connect the wires from the wall to the Cameras Pigtail and insert
them into wall.
A.4 - Position the Camera base over the marked holes from step 3-A.1.
A.5 - Secure the Camera with the provided screws.
B. Mounting to a Single gang Junction Box
We recommend the use of the WPS-MNT-FLUSH-BUL Flush Mount plate when
mounting to a single gang junction box. This plate is available in gray or
white to match the color of the Camera being used. Follow the instructions
in the WPS-MNT-FLUSH-BUL manual for using this mounting method and then
proceed to step 4.
8
WPS-350-BUL-A Installation Manual
4. Fine-Tuning Camera Adjustments
The Camera is equipped with a BNC Test Port that allows for local Analog
Video output for adjusting positioning, zoom, and focus.
The camera is supplied with a BNC Test Adapter that allows for viewing the
output of the camera on a monitor or the WPS-CCTV-TESTER (not included).
Use this connection to adjust the camera directly from the installed location.
Adjust Zoom
Adjust Focus
BNC Test Adapter
Connection
A. Remove the plate located at the rear of the Cameras just before the
Cameras base to access the BNC Test Adapter connection.
B. Connect the BNC Test Adapter to the Camera.
C. Connect the BNC on the adapter to a monitor or WPS-CCTV-TESTER video in.
D. Adjust the Cameras Rotation, Swivel, and Angle as dened in step 1 and
secure the set screws using the supplied 3mm Allen key.
E. Adjust the Cameras Zoom (closest to the lens) using the supplied 3mm
Allen key.
F. Adjust the Cameras Focus (furthest from the lens) using the supplied 3mm
Allen key.
G. Once the Zoom and Focus are adjusted, disconnect the BNC Test
Adapter and replace the plate removed in step 4-A.
© 2013 Wirepath Surveillance
9
WPS-350-BUL-A Installation Manual
TROUBLESHOOTING
If you have trouble operating the camera, rst refer to the following guidelines.
If the problem persists, contact Technical Support at 866.838.5052.
Nothing appears on the display
• Check if the power for camera and monitor is ON.
• Check if the VIDEO cable is connected to the camera BNC video
output jack.
• Check if the VIDEO cable is connected to the monitor VIDEO input jack.
Image appears dim on the display
• Check the monitor contrast setting.
• Check the monitor brightness setting.
• Check the lens. If necessary, clean with a soft, clean cloth.
• Check if the camera is facing towards a bright light. If so, change the
camera position.
• If a device exists between the camera and screen, conrm the signal
accepted by the screen is strong enough – 75 Ohm.
Image appears blurry on the display
• Check the focus of the lens.
• Check the lens. If necessary, clean with a soft, clean cloth.
The camera is not working properly and the camera housing is hot
• Check if camera is connected to the correct power source.
Condensation Appears on Camera Lens Cover
• Check the color of the beads in the Silica pack under the lens cover.
• If the blue crystals have turned pink indicating that the pack has
absorbed moisture, replace the pack with the spare provided with the
camera.
Camera Power Cycles Intermittently
• Check voltage at camera for proper voltage level.
• Connect camera locally with a different power supply to test.
10
SPECIFICATIONS
Image Sensor 1/3” Color Sony Super HAD II
Resolution (TVLs) 550
Effective Pixels NTSC:768(H)x494(V)
Gamma 0.45
S/N Ratio 48dB (AGC Off, Weight On)
Sync Mode Internal
Scanning System 2:1 Interlace
Lens 4 - 9 mm
IR Range 65 ft.
IR LED Count 24
Minimum Illumination 0.01 Lux color, 0 Lux IR on
Auto Gain Control Yes
WPS-350-BUL-A Installation Manual
Back Light Compensation Yes
White Balance Yes
Weather Rating IP66
Operating Temperature 14°F - 140°F
Operating Humidity 30% - 80% RH
Power Source 12 VDC (500 mA)
Power Consumption 3.5W- 290mA
Dimensions 8.39” (L) x 3.82” (H)
Weight 1.70 lb. (770g)
© 2013 Wirepath Surveillance
with sun shade and bracket fully extended
11
WPS-350-BUL-A Installation Manual
DIMENSIONS
3.24in.
1in.
9.07in.
8.39in.
3.73in.
0.6in.
Ø 3.06in.
12
WPS-350-BUL-A Installation Manual
WARRANTY
5-Year Limited Warranty
This camera has a 5-Year Limited Warranty. The warranty includes parts
and labor repairs on all components found to be defective in material or
workmanship under normal conditions of use. This warranty shall not apply to
products which have been abused, modied, disassembled or improperly
installed. Products to be repaired under this warranty must be returned to
Wirepath™ Surveillance or a designated service center with prior notication
and an assigned return authorization number (RA).
CONTACTING TECHNICAL SUPPORT
Phone: (866) 838-5052
Email: Techsupport@snapav.com
© 2013 Wirepath Surveillance
13
130221-1445
© 2013 Wirepath Surveillance
Loading...