Staub Electronics SM-PROJ-M-BLK User Manual
ADJUSTMENTS
To change the tilt of your projector, use Allen Key (D) to rst loosen the
Allen Screws on the Mount Base (M). Tilt the projector into the desired
position and re-tighten the screws.
To change the direction your projector faces, rst loosen the set screw
with the Allen Key (E). Turn the projector to the desired direction and
re-tighten the set screw.
WARNING: When adjusting the direction, only turn the mount
enough to reach the desired direction. DO NOT CONTINUALLY
TURN THE PROJECTOR IN A COUNTER-CLOCKWISE DIRECTION! This
can cause the mount to come apart and may cause damage and/or injury.
Lifetime
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes
parts and labor repairs on all components found to be defective in material
or workmanship under normal conditions of use. This warranty shall not apply
to products which have been abused, modied or disassembled. Products to be
repaired under this warranty must be returned to Snap AV or a designated service
center with prior notication and an assigned return authorization number (RA).
SM-PROJ-M-BLK
Strong™ Universal Projector Mount
for Medium Size Projectors (Black)
For Technical Support call 1.866.838.5052
engineered by
10405 Granite Street Charlotte, NC 28273 | 1.866.424.4489
INSTRUCTION MANUAL
ASSEMBLY INSTRUCTIONS
SPECIFICATIONS
• Maximum load: 30 lbs.
• Tilt range: +/- 70°
• Horizontal rotation: 360°
WARNINGS
1. Make sure these instructions are read and thoroughly understood
before attempting installation. If you are unsure of any part of the
installation process, contact a professional installer for assistance.
2. The wall or mounting surface must be capable of supporting the
combined weight of the mount and the display; otherwise the
structure must be reinforced.
3. Safety gear and proper tools must be used. Failure to do so can result
in property damage and/or serious injury.
4. Follow all instructions and recommendations regarding adequate
ventilation and suitable locations for mounting your display. Consult
the owner‘s manual for your display for more information.
PACKAGE CONTENTS
(A) Wood screw x2
(B) Concrete Anchor x2
(F) M4 x 16 Screw x4
(G) M4 x 30 Screw x4
BOX CONTENTS
• Wall mount
• Instruction manual
• Hardware kit
(K) M6 x 30 Screw x4
(L) Washer x4
(O) Mount Arm x4
(P) 6mm Spacer x4
TOOLS REQUIRED
• Phillips Head Screw Driver
• Electric or Portable Drill
• 3/16” (5 mm) Drill Bit and Stud Finder for Drywall Installation
• 5/16” (8 mm) Masonry Bit for Concrete Installation
INSTALLATION
Step 1 - Installing The Ceiling Plate
Attach the Ceiling Plate (N) to the ceiling
using the Wood Screws (A). If you are installing
into a concrete ceiling, also use the Concrete
Anchors (B).
Step 2 - Installing the Mount Body
Screw the Mount Body (Q) onto the Ceiling
Plate (N) by turning it clockwise. Tighten the
set screw(s) using the Allen Key (E).
Step 3 - Attaching the Mount Arms to the Mount Base
Secure the Mount Arms (O) to the Mount Base (M)
using the Arm Screws (C) and Washers (L). Leave
the Arm Screws (C) loose so that you can adjust
them when attaching the projector.
Step 4 - Attaching the Mount Arm Assembly to the Projector
Attach your projector to the Mount Arms (O) using the
correct screw from the hardware kit (F, G, H, I, J, or K).
If none of these screws t, check with the manufacturer
of your projector for the proper size. Depending on
the surface of the projector, you may want to use
spacers (P) between arm and projector. Once
attached, make sure all screws are tight.
(E)
(M)
(D)
(N)
(A)(A)
(N)
(Q)
(C)
(L)
(O)
(Q)
(M)
(C) Arm Screw x4
(D) 6mm Allen Key x2
(E) 3mm Allen Key
CAUTION: This wall mount is intended for
use only with the maximum weight of 30 lbs
(H) M5 x 16 Screw x4
(I) M5 x 30 Screw x4
(J) M6 x 16 Screw x4
(M) Mount Base x1
(N) Ceiling Plate x1
(Q) Mount Body x1
Step 5 - Attaching the Projector to the Mount Body
Carefully hook the Mount Base (M) with your projector
attached to the Mount Body (Q). Tighten the Allen
Screws on all four sides of the Mount Base (M) with
Allen Key (D) to prevent the projector from being
knocked o the Mount Body (Q).
Installation is now complete.
Hint: Using both Allen Keys (D), one on each side,
will help with consistent tightening.
(Q)
Tilt Adjustment Screws
Swivel
Screw
Loading...