Staub Electronics SM-LP-F-M User Manual
Part 1a – Mounting the Wall Plate (Drywall)
Important! For safety, this mount must be secured to two adjacent wood studs at least 16” apart.
2. Place the wall plate against the wall and level it using the bubble guide.
3. Mark the two locations (one per stud) on the wall where the mount will be secured. Be sure to use the
center of each stud.
4. Remove the wall plate and drill a 1/4“ (6 mm) pilot hole at each location using an electric drill.
Lag Bolt Washers (R) provided (Fig. 1).
6. Do not over-tighten the bolts and do not release the wall plate until all screws are secure.
Part 1b – Mounting the Wall Plate (Concrete)
1. Place the wall plate against the wall and level it using the bubble guide.
3. Place the wall plate aside and drill a hole at each location using a 3/8” (10 mm) masonry bit. Remove
any excess dust from the holes.
4. Insert one Concrete Anchor (P) into each hole. A hammer can be used to lightly tap the anchors into
place if necessary.
Lag Bolt Washers (R) provided (Fig. 2).
6. Do not over-tighten the screws and do not release the wall plate until all screws are secure.
Universal Fixed Wall Mount
SM-LP-F-M
Installation Instructions
Part 3 – Final Installation and Adjustment
1. With the help of another person, carefully lift your display and place it on the wall plate (Fig. 5). Do not
release the display until the mounting arms have securely hooked onto the mount.
2. Important! Insert the safety bar at the bottom of the mount to avoid having the display accidentally
display (Fig. 6).
backs...
For displays with curved
or recessed backs...
Bag # (Ref ) Item (Qty)
(A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4)
1
(D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4)
2
(G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4)
3
(J) M8x16 Bolt (x4)
(K) M8x40 Bolt (x4)
4
(M) Small Spacer (x4)
5
(P) Concrete
Anchor (x3)
(Q) M8 x 63
Lag Bolt (x3)
6
(L) M8 Lock Washer (x4)
(C) M4 Lock Washer (x4)
(F) M5 Lock Washer (x4)
(I) M6 Lock Washer (x4)
(N) Large Spacer (x4) (O) M6 Washer (x4)
(R) Lag Bolt
Washer (x3)
Fig. 4 - Use a longer bolt and
spacer for displays with curved
or recessed backs. Do not use
the M6 Washer (O) if you are
using the M8 Bolts (J or K).
Fig. 5 - Carefully hook the display onto
the wall plate.
Fig. 6 - A small padlock can be used to
help prevent theft of your display.
Warnings
1. Make sure these instructions are read and completely understood before attempting installation. If
you are unsure of any part of this installation, contact a professional installer for assistance.
2. The wall or mounting surface must be capable of supporting the combined weight of the mount
and the display; otherwise the structure must be reinforced.
3. Safety gear and proper tools must be used. A minimum of two people are required for this
installation. Failure to use safety gear and/or attempting this installation alone can result in property
damage, serious injury, or death.
4. Follow all instructions and recommendations regarding adequate ventilation and suitable locations
for mounting your display. Consult the owner‘s manual for your display for more information.
5. This mount is equipped with a safety device that must be used whenever the mount holds a display.
Not using the safety device can cause property damage, serious injury, or death.
Tools Required
Phillips Head Screwdriver
Ratchet or Driver with 1/2” (13 mm) Socket
Portable or Electric Drill
1/4“ (6 mm) Drill Bit and Stud Finder for Drywall Installation
3/8” (10 mm) Masonry Bit for Concrete Installation
Hardware Kit
Part 2 – Attaching the Arms to the Display
Important! Use extra care during this part of the installation. If
possible, avoid placing your display facedown as it may damage the
viewing surface.
NOTE: Your mount comes with a selection of bolt diameters and
lengths to accommodate a wide variety of display models. Not all of
the hardware in the kit will be used.
1. Determine the correct length of bolt to use with your display by
A.
bolts (A, D, G, or J) from the hardware kit.
B. If your display has a curved or recessed back, you will use one
of the longer bolts (B, E, H, or K) along with a spacer (M or N).
2. Determine the correct diameter of bolt to use by carefully trying
one bolt each from Bags 1 - 4 of the hardware kit. Do not force
any of the bolts – if you feel resistance stop immediately and try
a smaller diameter bolt.
3. Attach the arms to the back of your display using the bolts identi-
(C, F, I, or L) (see Fig. 3 and 4).
A. If you are using the M4, M5, or M6 bolts (Bags 1, 2, and 3
respectively), you will also need to use the M6 Washers (O).
B. If you are using one of the longer bolts on a display with a
curved or recessed back, you will also use a Spacer (M or N).
Use the Smaller Spacer (M) for M4 and M5 bolts and the Large
Spacer (N) for M6 and M8 bolts.
4. Make sure all screws are secure, but do not over-tighten them.
(Q) M8 x 63 Lag Bolt
(R) Lag Bolt Washer
Fig. 2 - Attach the wall plate to the wall (concrete).
Fig. 1 - Attach the wall plate to the wall (drywall).
(Q) M8 x 63 Lag Bolt
(R) Lag Bolt Washer
Fig. 3 - Attach the arms to the back
of your display.
(Q) M8 x 63 Lag Bolt
(R) Lag Bolt Washer
(R) Lag Bolt Washer
(R) Lag Bolt Washer
(Q) M8 x 63 Lag Bolt
(Q) M8 x 63 Lag Bolt
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes
parts and labor repairs on all components found to be defective in material
or workmanship under normal conditions of use. This warranty shall not apply
repaired under this warranty must be returned to Snap AV or a designated service
For Technical Support call 1.866.838.5052
Lifetime
CAUTION: This wall mount is intended for use
only with the maximum weight of 88 lbs
engineered by
Loading...