Staub Electronics SM-F-L User Manual
Step 3: Hang television on to the Wall Plate
a. Carefully lift the television to hook the arms over the
top lip of the wall plate. Allow the lower portion of the
arms to swivel in under the bottom lip of the wall plate.
Do not release the television until it is completely
connected to the wall plate.
ADJUSTMENTS:
SM-F-L / SM-T-L
Strong™ Universal Fixed and Tilt Mount
for Large Displays
Adjust Horizontal Level and Tilt
Forward Tilt Adjustment (SM-T-L)
a. Turn Tilt Adjustment Lever (ratchet) clockwise to tighten grip;
counter-clockwise to loosen grip.
b. Pull Tilt Adjustment Lever (ratchet) away from arm and then
turn Clockwise/counter-clockwise to desired location. Let
the Tilt Adjustment Lever (ratchet) sit in place.
c. Repeat steps A & B as needed to loosen/tighten the tilt.
Horizontal Adjustment
a. If display is not horizontally level when mounted, Tilt
Adjustment Screws are included at the top of each arm
for micro-adjustments (see photo to the right). Use provided
Long Allen Key (X) to raise or lower the screw, which will in
turn raise or lower the mount.
Note: Due to display weight, it may be easier to lift panel
slightly when adjusting the screw. Caution should be taken
to avoid any slips or drops to avoid damage and/or injuries.
Locking
Tilt Adjustment Lever
(Ratchet)
±5° Horizontal
Adjustment
Tilt Adjustment
Screw
a. To lock the arms to the wall bracket, twist the locking tabs
until the edge catches behind the bracket. The Allen Key (X)
can be used as a tool to help with this step. Padlock is
optional (not included).
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective
Lifetime
in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modied or
disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notication
and an assigned return authorization number (RA).
For Technical Support call 1.866.838.5052
Locking
Tab
INSTRUCTION MANUAL
NS
WARNINGS:
• Installation by a qualied professional is highly recommended for this product.
• Do not begin installation until you have thoroughly read and understand these instructions.
• This mount supports displays from 36” to 60”, VESA 700x500, and a maximum load of 165 lbs (75 kg).
• Ensure the mounting wall will safely support four times the combined weight of the Mount
and display panel.
• Under no circumstances should this product be mounted to metal studs.
• The manufacturer does not accept responsibility for incorrect installation.
CAUTION:
This wall mount is intended
SPECIFICATIONS:
• Maximum Load: 165 lbs. (75 kg)
• Display Size: 36” to 60”
• Forward Tilt Range: - 8° /+ 13°
• Horizontal Tilt Range: +5°
BOX CONTENTS:
• Wall Plate (1)
• Arm left (1)
• Arm right (1)
PACKAGE CONTENTS:
Wall Plate
Arms
(With SM-T-L)
(X) Allen Key (x1)
Arms
(With SM-F-L)
TOOLS REQUIRED:
• Power Drill
• 5/16” and 1/4” Drill Bit
• Phillips Head Screw Driver
• Level
• Socket Wrench
with 7/16” Socket head
HARDWARE KIT
Pkg 1
(A) M4x12 Bolt (x4)
Pkg 2
(E) M5x12 Bolt (x4)
Pkg 3
(I) M6x12 Bolt (x4)
Pkg 4
(M) M8x16 Bolt (x4)
Pkg 5
(Q) Small Spacer (x4)
Pkg 6
(U) Concrete
Anchor (x6)
(B) M4x20 Bolt (x4)
(F) M5x20 Bolt (x4)
(J) M6x20 Bolt (x4)
(N) M8x25 Bolt (x4)
(R) Large Spacer (x4)
(Q) M10x80
(V) M8x63
Lag Bolt (x4)
Flange Bolt (x6)
(C) M4x30 Bolt (x4)
(G) M5x30 Bolt (x4)
(K) M6x35 Bolt (x4)
(O) M8x40 Bolt (x4)
(S) M8x18x10 Spacer (x4)
for use only with the
maximum weight of
165 lbs (75kg).
(D) M4 Lock Washer (x4)
(H) M5 Lock Washer (x4)
(L) M6 Lock Washer (x4)
(P) M8 Lock Washer (x4)
(T) M6 Washer (x4)
(W) Lag Bolt
Washer (x6)
INSTALLATION:
Step 1: Mounting the Wall Bracket Assembly
For Mounting on a Stud Wall
a. Pre-drill holes into two wood studs using a 1/4” drill bit.
Be sure to drill into the center of the studs at least
2-1/2” deep. The use of a stud nder is highly
recommended.
b. Insert four ange bolts (V) into holes through the Wall
Plate and tighten down.
WARNING: Tighten bolts so that wall plate is rmly
attached, but do not overtighten. Overtightening
can damage the bolts, greatly reducing their
holding strength.
For Mounting on a Concrete Wall
a. Pre-drill holes into concrete using 5/16” drill bits to a
depth of 2 1/2”. Insert concrete wall anchors (U)
and tap in-with hammer, if necessary (Figures 2 & 3).
WARNING: When installing wall arm assembly on
cinder block, verify rst that you have a minimum
of 1-3/8” of concrete thickness to be used for the
concrete anchors. Do not drill into mortar joints! Be
sure to mount in a solid part of the block, generally
1”minimum from the side of the block. Cinder block
must meet ASTM C-90 specications. It is suggested that
a standard electric drill on slow setting is used to drill the
hole instead of a hammer drill to avoid breaking out the
back of the hole when entering a void or cavity.
Concrete must be 2000 psi density minimum.
Lighter density concrete may not hold concrete
anchor.
Make sure that the supporting surface will safely
support the combined load of the equipment and
all attached hardware and components.
b. Insert four ange bolts (V) into the wall anchors
through the Wall Plate. Tighten all bolts.
WARNING: Tighten bolts so that wall plate is rmly
attached, but do not overtighten. Overtightening
can damage the bolts, greatly reducing their
holding strength.
Step 2: Mount Arms to television
a. Determine the diameter of the screw (parts A through
P) your TV requires by carefully trying to hand-thread
one into the threaded insert on the rear of the TV. If
there is any resistance, stop immediately.
b. Spacers are commonly needed on televisions with
curved backs or recessed screw inserts. The screw
will thread through the appropriate washer (D, H, L,
or P), any spacer needed (Q, R, or S) and the arms
into the TV.
c. Ensure the arms are installed at side to television
and are square to each other after all screws have
been installed (Figure 4).
Figure 1
Cutaway View
Correct
plaster/
drywall
concrete
Figure 2
Drill holes and
insert anchors.
Place wall arm
assembly plate
over anchor and
secure with
ange bolt.
Tighten all
ange bolts.
TIP: To assist in
installation, the
wall bracket features
a screw slot for
temporary hanging
of the bracket.
Incorrect
plaster/
drywall
concrete
Concrete
Wall
Wall Arm
Flange Bolt
Figure 3
Figure 4
Loading...