Status Pro R280 Instruction Manual

R280

Bluetooth Laser Receiver

Instruction Manual

Another fine solution by

R280

Instruction Manual – English

Laser Receiver R280
(BG 831500)

Software version V 1.00

We would like to congratulate you on the purchase of your Status Pro R310 Laser receiver.
Before initial usage you should carefully read the safety instructions as well as the user
guidelines contained in this manual. We wish you every success when using this
Measurement Instrument.
Please note: User Manuals can be amended when improvements or changes to the pro­duct range have been carried out. Use the link below to make sure you have the most up
to date version of your User Manual: www.statuspro.com.

2

Status Pro – R280 Instruction Manual

CONTENT

Content

1. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Class of Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Advice on batteries / rechargeable cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Instrument care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.6 Calibration and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.7 Liability exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 Button Panel of the R280 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2 LED Signals from the R280 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.3 R280 Monitor Control Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4. MEASUREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Setting up a laser plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Checking and calibrating the T330 Self-Levelling function . . . . . . . . . . . . . . . . . . . . 12

5. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

6. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7. PRODUCTS AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8. MEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1. Safety Instructions

1.1 Class of Laser

The laser light emitted from a Status Pro Laser has an Output Rating of < 1,0 mW.
The Laser is placed in the category „Class 2“ and is classified as safe for the use as
a measurement instrument. There are however a few safety aspects to be observed:

Status Pro – R280 Instruction Manual

3

R280

Caution!

• Do not stare into the laser beam.

• Do not point the laser beam at other people.

• Observe the local safety guidelines on Site and if in doubt consult

• Do not use the equipment in damp or moist locations.

• Ensure shading of the equipment against direct sunlight or heat

• Fluids or rain as well as extreme temperature conditions may

Note

Do not violently shake the Laser or other sensors and always
protect against falls. This can damage the structure or the optics
of the instrument resulting in false measurements.
Do not touch rotating parts when in use!

1.2 Standards

SAFETY INSTRUCTIONS

the Site safety Engineer.

sources.

damage the equipment.

All Status Pro Laser and Receiver Instruments are developed and manufactured
according to the following CE Standards:

• EN 55 011

• EN 55 022

• EN 61 000-4-2

• EN 61 000-4-3

• EN 60 335

1.3 Advice on batteries / rechargeable cells

If the equipment is being stored for a longer period of time or being powered using Mains,
then the batteries should be removed to prevent damage of the instrument through
leakage.

4

Status Pro – R280 Instruction Manual

SAFETY INSTRUCTIONS

When using rechargeable cells always observe the specific charging procedures for the
cells.

Rechargeable cells can be recharged around 1000times when treated correctly, but there
is no guarantee!

Caution!

Do not try to recharge normal batteries. Do not expose batteries
or rechargeable cells to fire or excess heat (Danger of explosion).
Do not mix batteries and rechargeable cells.
Always use batteries and cells of the same kind.
Do not mix old and new batteries or cells.

Note

Help to protect the environment! Empty batteries do not belong in
the household waste disposal system. Only deposit empty or
damaged cells at a collection point specially designed for this
purpose.

1.4 Instrument care

Your measurement instrument is designed for use in an industrial environment and can
withstand water splashes or light spray as well as dust. Clean the equipment using a soft
cotton cloth and a mild soap solution. Laser apertures as well as well as sensor areas
should only be cleaned using a soft, dry and dust-free cloth. Do not use paper towels to
clean glass surfaces as they could scratch. Avoid contact with grease, oil or oil-based
solutions when handling the equipment.

1.5 Maintenance

The mechanical components of your equipment are prone to natural wear and tear! If the
Instrument appears to have a technical defect, contact the Manufacturer. Do not try to

Status Pro – R280 Instruction Manual

5

R280

repair or open the sensor casing. Attempted repairs through unauthorised personnel
makes the guarantee null and void! Always store the equipment under dry conditions and
use the case for transportation.
To ensure trouble-free processing, simply fill in the form you will find using the following
link: www.statuspro.com/machine_geometry/service_support/calibration_repair

Advice

To be able to identify the equipment when seeking advice always
quote the serial number of the equipment. The Manufacturer does
not accept any responsibility for damage incurred through incorrect
maintenance carried out by non-authorised personnel.

1.5 Calibration and repair

To guarantee measurement accuracy, and reliable operation of your Status Pro
Measurement System, it is of utmost importance that the recommended Service Intervals
be adhered to. The System should be checked for serviceability, and re-calibrated by the
Status Pro workshops every 12 months.
Within the scope of the service checks, the complete system will also be examined for
possible wear or damage, as well as receiving any software updates. The date of the next
service check for your equipment is stamped on the Status Pro calibration sticker.
To ensure trouble-free processing of the service and calibration checks, simply fill in the
form you will find using the following link

www.statuspro.com/machine_geometry/service_support/calibration_repair.

SAFETY INSTRUCTIONS

1.6 Liability Exclusion

The Status Pro GmbH does not accept responsibility for damage incurred through incor­rect use or handling of the equipment. To ensure correct usage, a founded knowledge of
the equipment is essential. It is of the utmost importance that you read and understand
the Handbook!
No responsibility will be accepted for damage incurred through ignorance or disregarding
of the operating instructions.

6

Status Pro – R280 Instruction Manual

GETTING STARTED

2. Getting started

2.1 Power Supply

The R280 can only be powered using a Type BT 800071 re-chargeable cell. A completely
charged cell will provide enough energy for around 8 hours usage. A discharged cell can
be recharged in approximately 1,5 hours using the external charger (BT 800072) . Constant
operation is possible if a second cell is available (optional extra).
The battery pack (III) can be accessed by opening the rear cover (I) . To open the cover,
simply pull, using the two indentations(II), the cover is held in place with a magnet.

I

The battery is placed in the housing with the contacts
pointing to the middle of the sensor. The battery is placed
correctly when the rear cover closes without any resi­stance. Due to the shape of the housing it is normally
possible to fit the cell incorrectly.

Status Pro – R280 Instruction Manual

II

III

IV

7

R280

Please follow instructions below:

➜ Cell fitted correctly (Contacts deepest position in the housing)
➜ For use solely with cell type: BT 800071
➜ Remove cell before prolonged storage (Danger of corrosion)

2.2 Assembly

The R280 Laser receiver has two M8 threads (V) on the underside and two on the top side.
The threads enable correct fitting of the Magnet Adapter Typ BG 831510, usually used
when measuring objects. The Adapter consists of a switcheable magnet (VII) and a revol­veable column (VIII). The adapter can be fitted at either end of the sensor.

GETTING STARTED

IX

VIII

V

VII

VI

Adapter BG 831510

8

Status Pro – R280 Instruction Manual