Status Instruments TTR200X, TTC200X, SEM1801XR, SEM1802XR, SEM1801XTC User Manual

D2598-01-01 CN5370 USBTTX CONFIG User Guid e

IMPORTANT - CE & SAFETY REQUIREMENTS

Product must be used inside a suitable safe area.

The product contains no serviceable parts, or internal adjustments. No attempt must be made to repair this product. Faulty units must be
returned to supplier for repair.

This product must be used by a qualified person.

ABSOLUTE MAXIMUM CONDITIONS ( To exceed may cause damage to the unit) :-

Ambient Temperature (0 to 40) °C Humidity (10 to 95) % RH (Non condensing)

USBTTX CONFIG USER GUIDE

ATEX APPROVED MODULE FOR TTR200X, TTC200X,
SEM1801XR, SEM1802XR, SEM1801XTC, SEM1802XTC

FOR USE IN SAFE AREA ONLY.

Every effort has been taken to ensure the accuracy of this document, however we do not accept responsibility for damage, injury, loss or
expense resulting from errors and omissions, and we reserve the right of amendment without notice.

Important - Please read this document before any installing.

1.1 The USBTTX ATEX approved module in conjunction with the USB-CONFIG-MKII configuration unit provides a USB powered
interface between a Windows computer and Status Instruments TTR200X, TTC200X, SEM1801XR, SEM1802XR, SEM1801XTC,

SEM1802XTC configurable temperature and process instruments.

2.1 Please inspect the packaging and instrument thoroughly for any signs of transit damage. If the instrument has been damaged,
please notify your supplier immediately

Status Instruments Ltd, Status Business Park, Gannaway Lane, Tewkesbury, Gloucestershire, UK, GL20 8FD
Web Page: www.status.co.uk email : [e-mail] Technical Support : [e-mail]
Tel : [phone] Fax: [phone]

1.0 DESCRIPTION

3.0 PRECAUTIONS

2.0 RECEIVING AND UNPACKING

1.2 Using a standard PC USB port the module enables the user to interrogate their equipment. The transmitter or any connections to it
must be located in the safe area. Including re-ranging and re-configuration using a Windows based interface.

3.1 Do not allow the two terminal/crocodile clip connections on the output of the USB-CONFIG-MKII to short together, the module
provides 24V DC across these terminals in order to power the unit under configuration. Whilst the USB Config is protected by a self­resetting circuit, certain models of PC are not protected against high current draw from their USB ports and damage could be caused
if the user is not careful.

3.2 Do not attempt to configure anything but approved configurable equipment; doing so could damage the USB Configuration
equipment as well as the host computer.

3.3 Connecting the USB configuration module to powered equipment incorrectly can permanently damage the USB configuration
equipment or the TTR200X, TTC200X, SEM1801XR, SEM1802XR, SEM1801XTC or SEM1802XTC.

3.4 Do not use the USB Configuration equipment as a power supply, and ensure that it is not (accidentally or intentionally) used to
power a process loop or any other instrument.

Configuration – Only to be performed in the safe area

EX

The TTR200X, TTC200X, SEM1801XR, SEM1802XR, SEM1801XTC, and SEM1802XTC can only be configured whilst connected to the
USBTTX and USB-CONFIG-MKII, powered by a Windows computer . This may only be performed in the safe area.

Note:- The instructions contained in this document superceed any information or documentation supplied with the USB-CONFIG­MKII module when it is used with the USBTTX.

D2598-01-01 CN5370 USBTTX CONFIG User Guid e

4.0 OPERATION

5.0 SPECIAL CONDITIONS FOR USE

4.1 To use your USB configuration equipment you will first need to install USB Speedlink software, which is available as a free
download from http://www.status.co.uk/software.html . You will also need a Status Instruments USB-CONFIG-MKII configuration
module.

4.2 Connect the USB-CONFIG-MKII module to a Windows computer using the integaral USB lead, connect the USB-CONFIG-MKII
module to the USBTTX ATEX unit with the jack plug and socket connection.

4.3 Use either the crocodile clips or the ferrule conectors to attach the USBTTX module via its jack plug connection to the (4 to 20) mA
loop connection pins on the TTR200X, TTC200X, SEM1801XR, SEM1802XR, SEM1801XTC or SEM1802XTC.

4.4 Connect the unit you wish to configure to the USBTTX module via the appropriate leads, refer to the instruments user guide for
the connection details.

4.5 The software will recognise when the USB-CONFIG-MKII module is attached. This may take a few minutes the first time the USB­CONFIG-MKII Module is attached while the software drivers are loaded.

4.6 In the USB Speedlink software select the type of instrument to be configured, the USB equipment will now communicate with the
instrument and present the correct screen for configuring the instrument.

4.7 Note:- For SEM1802XR and SEM1802XTC each channel will need to be connected to and configured individualy.

5.1 The USBTTX is only to be connected to a Windows personal computer or Windows laptop type computer via a Status Instruments
USB-CONFIG-MKII module

5.2 The USBTTX with USB-CONFIG-MKII and connected computer are only to be used in the safe area

6.0 MARKING

7.0 GENERAL INFORMATION

7.1 The ATEX USBTTX module is powered completely from the USB port on your computer via the Status Instruments USB-CONFIG­MKII; you do not require an external power supply for configuration. The USBTTX module will power the instrument connected to it
during the configuration process for configuration and can also take live readings and perform certain adjustments.

It is not recommended to leave the module plugged into a laptop computer for long periods of time when the laptop is running on
batteries as this will affect battery life adversely, especially if an instrument is left connected to the configurator.

7.2 If you have any questions regarding the configuration of Status Instruments equipment please contact your supplier.

7.3 Please see the Status Instruments website –

http://www.status.co.uk for a wide range of temperature and process equipment

with direct PC to instrument USB configuration, removing the need for a configuration module altogether.

AC

USB-CONFIG-MKII

Power Lead

USBTTX

-

+

TTR200X
TTC200X

CONNECTION OPTIONAL

AC

USB-CONFIG-MKII

Power Lead

USBTTX

-

+

CONNECTION OPTIONAL

SEM1801XR
SEM1802XR
SEM1801XTC
SEM1802XTC

RED WIRE

RED WIRE

BLACK WIRE

BLACK WIRE

5.3 Indoor use only. The temperature sensor must be located in the safe area when being used with the USBTTX Config. For use with
TTC200X, TTR200X, SEM1801XTC – SEM1802XTC and SEM1801XR- SEM1802XR temperature sensors certified under IECEx TRC

10.0008X & TRAC09ATEX11232X